Welch Vacuum 2585B-50 User Manual

WELCH-

OWNER’S MANUAL FOR

DRY VACUUM PUMP MODELS

2585B-01, 2585B-50, 2585B-55 & 2585Z-50

I

L

MV

A

C

Not recommended for pumping acid, base or

organic vapors or gases.

Be sure to properly identify intake and discharge

before using pump. See section 2.5

Welch-Ilmvac
5621 W. Howard Street
Niles, IL 60714
Phone: [phone] (Technical Support)
Fax: [phone]
E-Mail: [e-mail]
Web-Page: www.welchvacuum.com

Warning

Warning

Part No. 642799B

Printed in USA

INSTRUCTION

WARNING AND CAUTION

PLEASE READ BEFORE OPERATION

While reading your manual, please pay close attention to areas labeled:

WARNING AND CAUTION.

The description of each is found below.

WARNING

Warnings are given where failure to observe instruction could result

in injury or death to people.

CAUTION

Cautions are found where failure to observe the instruction could result

in damage to the equipment, associated equipment and process.

These units confi rm to the SI International system of units of measurement.

The following symbols (with recommendation of IEC1010 ) of warning will be found on the pump.

Caution - refer to accompanying documents

Caution - risk of electrical shock

Caution - hot surface

WARNING

Motor includes a self resetting thermal cutout and the pump could

restart without actuation under fault condition.

2

TABLE OF CONTENTS

Section 01 - Installation

1.01 Unpacking

1.02 Pump Mounting

1.03 Pump Location / Environmental Conditions

1.04 Exhaust Provisions

1.05 Electric Power

1.06 Vacuum Connections

1.07 Vacuum Gauges

1.08 Vacuum Pump Oil

Section 02 - Pump Features & Principles of Operation

2.01 General Description

2.02 Principles of Vacuum Pump Operation

2.03 Effects of Continued Pressure Reduction

2.04 Ultimate Pressure

2.05 Pump Mechanism Description

2.06 Intake Anti-Suckback Protection

2.07 Pump Lubrication

2.08 Exhaust Filter

2.09 Gas Ballast Valve

2.10 UNIBARBTM Intake Fitting

Section 03 - Specifi cations

3.01 Specifi cation Chart

Section 04 - Motor Power Specifi cations / Features

4.01 Motor Specifi cation Chart

4.02 Changing the Voltage Settings for Global Motor Option on “A”-Models

4.03 Changing the Voltage Settings for Global Motor Option on “C”-Models

4.04 Changing the Voltage Settings on “A”-Models

4.05 Other Electrical Confi gurations

4.06 Explosion Proof Pumps

Section 05 - Operation

5.01 Starting Procedure

5.02 High Pressure Operation

5.03 Shutdown Procedures

3

Section 1: SAFETY INFORMATION

I.10 CAUTION: To prevent injury.
I.11 Never operate this product if it has a damaged cord or plug. If it is not working properly, has

been dropped, damaged or has fallen into water, please return the product to a Welch service
center for examination and repair.

I.12 Keep the cord away from the heated surfaces.
I.13 Never block any air openings or place it on a soft surface where the openings may be blocked.

The air openings are for ventilation of the motor inside the housing. Keep all air openings free
of lint, dirt and other foreign objects.
I.14 The PTFE pump is thermally protected and can automatically restart when the protector resets.
Always disconnect power source before servicing.

I.15 Wear safety glasses or goggles when operating this product.
I.16 Use only in well ventilated areas. The motor is fan cooled enclosed in a shell.

WARNING

Do not operate the pumps in an atmosphere containing

I.17 All electrical products generate heat. To avoid serious burns never touch unit during or

immediately after operation.

I.18 Be sure to properly identify intake and discharge before using pump. See Section II-5.

I.20 CAUTION: To reduce risk of electrical shock....

I.21 Do not disassemble. Disassembly or attempted repairs if accomplished incorrectly can create

electrical shock hazard. Refer servicing to qualifi ed service agencies only:
Call [phone] Ext. 1
I.22 Unit is supplied with a three pronged plug. Be sure to connect pump to a properly grounded
outlet only.

I.23 WARNING: To reduce risk of electrocution.
I.24 Do not use this product in or near area where it can fall or be pulled into water or other liquids.
I.25 Do not reach for this product if it has fallen into liquid. Unplug immediately.
I.26 Never operate this product outdoors in the rain or in a wet area.
I.27 DANGER: To reduce risk of explosion or fi re…
I.28 Do not use this pump near explosive atmospheres or where aerosol (spray) products are being

used.

I.29 Do not use this product near fl ames.

Never block the exhaust port. If the exhaust is blocked, pressure

will build-up in the pump with the potential of the pump head

bursting and causing possible injury to personnel in the area.

fl ammable or explosive gases/vapors.

WARNING

WARNING

Failure to observe the above safety precautions could result

in severe bodily injury, including death in extreme cases.

4

Section 2: INSTALLATION

2.10 Introduction

tem now in your possession, but as a helpful reference and guide to prevent many problems which can
occur if used improperly.

2.11 Unpacking

Carefully remove the Dry Vacuum System from the shipping carton. Preserve all paperwork for future
reference. If damage has occurred from shipment a claim must be fi led with the carrier immediately;
preserve the shipping carton for inspection by the carrier. If you are required to communicate with your
dealer or Welch Vacuum be sure to include your order numbers for quick identifi cation. Do not return
the system to the factory without fi rst calling for a returned goods number. Call [phone]

2.12 System Mounting

Rubber feet are attached to the pump. Rubber feet are excellent for applications involving a

semi-fl exible surface such as a bench top; they help to isolate noise and eliminate creeping.

2.13 System Location and Enviromental Condition

The Dry Vacuum System should be located preferably in a clean, dry and well ventilated area. Please

be sure not to block the ventilation ports located on the metal shell. The pump should be placed where
the surrounding temperature remains between 10°C and 40°C (50°F and 104°F). Always check to in-
sure the location chosen is protected from direct or indirect moisture contact. The pump should
be located as closely to its system in order to utilize it most effi ciently. The pump is rated
for indoor use only.
Maximum altitude 2000 meters. Operating temperature range 5°C to 40°C. Maximum relative humidity
of 80% for temp. up to 31°C decreasing to 50% at 40°C. Rated for ±10% of supply voltage.
Pollution Degree2, Installation Category II.

2.14 Inlet and Outlet Provisions

A inlet hose barb which accepts ¼” I.D. hose makes it easy to connect the system to your concentrator,

rotary evaporator or gel dryer. Since the vacuum system operates in the viscous fl ow regime, the small
diameter of the hose will generate minimal conductance loss. For best results, Welch recommends the
length of the tubing between the pump and the apparatus be kept as short as possible. Hose clamps
should be used to hold the hose in place.
The hose barb in the outlet port of the pump accepts ¼” ID hose. A vent line can be attached to the
outlet hose barb which allows gases and vapors pumped through the pump to be piped to a fume hood.
Be sure to call Welch technical service prior to start-up at [phone] if you have any questions.

This manual has been compiled not only for the care and maintenance of the Welch Dry Vacuum Sys

WARNING

Don’t operate this pump in an atmosphere

containing fl ammable or explosive gases or vapors.

WARNING

The motor is thermally protected and will automatically

restart unexpectedly when the overload device resets.

WARNING

Never Block The Outer Port. If the outlet is blocked, pressure will

build up in the pump which can lead to the pump head bursting

creating the potential of serious injury.

remove plug from outer port.

5