Welch Allyn Medical Diagnostic Equipment 3470, 5770 User Manual

Disclaimer

Welch Allyn reserves the right to make changes in specifications and
other information contained in this document without prior notice, and the
reader should in all cases consult Welch Allyn to determine whether any
such changes have been made. The information in this publication does
not represent a commitment on the part of Welch Allyn.

Welch Allyn shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of this
material.

This document contains proprietary information which is protected by
copyright. All rights are reserved. No part of this document may be
photocopied, reproduced, or translated into another language without the
prior written consent of Welch Allyn, Incorporated.

 1999 Welch Allyn, Inc. All rights reserved.

The CE mark on the product indicates that the system has been tested to and
conforms with the provisions noted within the 89/336/EEC Electromagnetic
Compatibility Directive and the 73/23/EEC Low Voltage Directive.

Welch Allyn shall not be liable for use of our product with equipment
(i.e., power supplies, personal computers, etc.) that is not CE marked and
does not comply with the Low Voltage Directive.

C.S.A. Statement

This product must be used with a certified Class 2 power
supply or be powered by a certified SEL V (Safety Extra Low
Voltage) output.

RF Approvals This product complies with the following:

Safety Approvals

U.S.A. FCC Part 15.249 Certified
Australia C–TIC
Canada RSS 210 Certified
Europe ETS 300 328 Certified
Mexico NOM–EM–121–SCT1–1994 Certified
Singapore Type Approval for Spread Spectrum System

U.S.A. UL Listed, C22.2 No. 950 / UL 1950
Australia conforms to AS/NZS

Canada 3548cUL Listed
Europe TÜV Rheinland GS Licensed, EN 60950

Mexico NYCE Certified, NOM 19

(IEC 950) (Scanner and Base only, not on battery)

TABLE OF CONTENTS

Cordless Scanner Quick Start Guide

Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

About the Battery Pack 2. . . . . . . . . . . . . . . . . . . . .

Charging Your Battery Pack 3. . . . . . . . . . . . . . . . .

Associating the Cordless Scanner to a Base 4. .

Obtaining Factory Service 5. . . . . . . . . . . . . . . . . .

Technical Support 6. . . . . . . . . . . . . . . . . . . . . . . . .

Limited Warranty 6. . . . . . . . . . . . . . . . . . . . . . . . . .

Limited Warranty Durations 6. . . . . . . . . . . . . . . . .

Sample Bar Codes (back cover)

Cordless Quick Start Guide

i

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

FCC Class B Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio or television technician for help.

Caution: Any changes or modifications made to this device that are not
expressly approved by Welch Allyn, Inc. may void the user’s authority to
operate the equipment.

Note: To maintain compliance with FCC Rules and Regulations, cables

connected to this device must be
wire(s) have been grounded (tied) to the connector shell.

Canadian Notice

This equipment does not exceed the Class B limits for radio noise emissions as
described in the Radio Interference Regulations of the Canadian Department of
Communications.

Le present appareil numerique n’emet pas de bruits radioelectriques depassant
les limites applicables aux appareils numeriques de la classe B prescrites dans
le Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada.

shielded

cables, in which the cable shield

CDRH Laser Safety Statement

This product complies with US DHHS 21 CFR J Part 1040.10. This product is a
CLASS II LASER PRODUCT with a maximum output of 1.0 mW at 670
nanometers and continuous wave.

EN 60825–1 Laser Safety Statement

This product is classified as a CLASS 2 LASER PRODUCT with a maximum
output of 9.0 mW at 670 nanometers per EN 60825–1:1994, Issue 2, June 1997.

ii

Cordless Quick Start Guide