weiserlock Halo Installation Manual

67611001
Rev 01
GED2500

Parts List

Mounting
Plate

Adapter
Ring

Exterior Assembly

Interior Assembly

ENGLISH

Installation and User Guide

Required tools

Ruler

Additional Tools (depending on application)

Hammer Wood block Chisel

Prepare the door and check dimensions

1

Make sure your door is compatible. If you have a standard deadbolt mounted

A

separately from the handle below it, your door is compatible.

Compatible Not Compatible

Phillips head screwdriver

Weiser

1-800-501-9471

www.weiserlock.com

Not CompatibleNot Compatible

Batteries

Latch A

Latch B

Keys

For Latch / Strike

Strike

46780

03809

If drilling a new door, use the supplied template and the complete

door drilling instructions available at weiserlock.com/doorprep

B

For Lock

SmartKey

Too l

49191 64109 68611

Remove your existing deadbolt
from your door.

48654

Rim
Lock

Measure to conirm that the hole in the door is either

C D E F

21/8" (54 mm) or 11/2" (38 mm).

21/8"

54 mm

or

11/2"

38 mm

Install the latch and strike

2

Is the door edge chiseled?

A B

Note: Add itional door
prepara tion may be
require d for doors with
11/2" ( 38 mm) holes .
Consul t the deadbolt
drilling instructions at
weiserlock.com/doorprep

Latch / Strike

Measure to conirm that the backset is
either 23/8" or 23/4" (60 or 70 mm).

For

Bag

Mortise
Lock

backset

23/8" o r 23/4"

60 or 70 mm

(2x) (2x)

(2x) (2x)

03809

face lush against the door edge.

Integrated
Interior

Measure to conirm that the hole
in the door edge is 1" ( 25 mm).

actual size

46780

1"

25 mm

D

Which latch are you installing?Hold the latch in front of the door hole, with the latch

Measure to conirm that the door is between
13/8" and 2 " (35 mm and 51 mm) thick.

13/8 " –2"

35 – 51 mm

actual size

YES

chiseled

Use latch “A”. If the
latch bolt is not already
extended, extend the
latch bolt as shown.

A

or

Use latch “B”. If the
latch bolt is not already
extended, extend the
latch bolt as shown.

NO

not
chiseled

B

A

Is the D-shaped hole centered in the door hole?

C

YES

or

D-shaped hole D-shaped hole

No adjustment is required.
Proceed to next step.

Rotate latch face as
shown to extend latch.

A

B

NO

Latch “A” Latch “B”

UP is

on top.

A

03809*

(2x)

*Use longer
screws if
holes are
worn out.

Install the strike on the door frame.

E

Make sure the hole in the door frame is drilled a

minimum of 1" (25 mm) deep.

or

B

or

or

UP is

on top.

wood
block

1 / 4

Longer screws
install closest to

B

the door jamb.

46780

(4x)

door frame

Install the exterior keypad

3

For

Lock

Bag

48654

(2x)

actual size

What is the diameter of the hole in the door?

A

Diameter is 21/8"

Diameter is 11/2"

(54 mm)

or

21/8"

54 mm

Adapter Ring is required
for installation. Install on
Exterior Assembly.

Locate the screws for step 3D and keep them within reach.

B

48654

(2x)

38 mm

Adapter Ring is not
needed for installation
and may be discarded.

(38 mm)

11/2"

Install the exterior keypad and mounting plate.

D

a

The cable goes
underneath the latch.

c

Keep parallel to the

edge of the door.

b

Support the exterior
assembly during mounting
plate installation.

G

Route the cable
through the center
hole, then push it into
the bottom hole.

d

Remove the mounting plate from the interior assembly.

C

Tighten screws
eve nly. DO NOT over
tighten screws.

Install the interior assembly

4

Ensure the turnpiece shaft is pointing up, and remove the interior cover and

A B

battery pack from the interior assembly.

a

Remove the interior
cover from the
interior assembly.

b

Make sure turn
piece shaft is
rotated as shown.

48654

(2x)

Install the interior assembly onto the mounting plate.

a

Insert the key and
test the latch. If the
latch does not
extend or
retract
smoothly, adjust
the screws.

Remove the key
when inished,
and make sure
the latch bolt is
fully extended.

For

Lock

Bag

(2x)

49191

actual size

b

c

If the turnpiece shaft is pointing
down, place the cover back onto
the interior assembly and rotate the
turnpiece until you hear it click. You
may need to apply some force.
Once the turnpiece shaft is correctly
oriented, remove the cover again.

Incorrect:

If turnpiece shaft is not oriented
correctly, put the cover back on and
rotate the turnpiece as shown in step C .

d

Do not install

batteries

until step 5.

Ensure tight cable
connection.

c

align

Lay the excess cable
lat inside the bottom of
the interior housing.

d

49191

(2x)

bottom

hole

Ensure you are u sing

the correc t screws.

Using inco rrect

screws will d amage

the produc t.

2 / 4