Weiser SmartCode 5 Touchpad Electronic Lever GED1450 User Manual

64465001
Rev 01
GED1450

Parts in the box

ENGLISH

Installation and User Guide

Required tools

Ruler4 AA Batt eries

Additional Tools (depending on application)

Hammer Wood block

Prepare the door and check dimensions

1

Phillips head screwdriver

Weiser

1-800-501-9471

www.weiserlock.com

Latch

AA2A3

Strike

C

Keys Spindle

F2E

Exterior
Assembly

Mounting
Plate

SmartKey
Too l

Levers

Y1

Interior
Assembly

F

G

K

Fasteners

26298

N

L

M

P

Z

22044

H

T

27526 64156

UV

Y2

If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.weiserlock.com/doorprep.

Measure to conirm that the hole in

A

the door is 21/8" (54 mm).

See

note

below*

21/8"

54 mm

*If you are installing this lever below
an existing lock or you plan to install a
lock above this lever, make sure that the
distance between holes is at least 61/2"
(165 mm).

Measure to conirm that the backset is

B C D

either 23/8" or 23/4" (60 or 70 mm).

23/8" or 23/4"

60 or 70 mm

backset

Measure to conirm that the hole in
the door edge is 1" (25 mm).

1"

25 mm

Measure to conirm that the door
is between 13/8" and 13/4" (35 mm
and 44 mm) thick.

13/8" – 13/4"

35 – 44 mm

Install the latch and strike

2

Hold the latch in front of the door hole, with the latch

A C

face lush against the door edge.

lush

A

Are the latch holes centered in the door hole?

B

YES NO

or

No adjustment is required.
Proceed to next step.

Move the pin to
extend the latch.

Adjust the latch face (if needed).

For square corners

Proceed to step 2D.

For round corners

1. Remove square corner faceplate.

A

2. Install round corner faceplate.

A2

For doors without chiseled edge

Ensure A2
snaps into

place.

actual

size

Is the door edge chiseled?

D

NP

YES NO

chiseled

slant of latch

bolt faces
door frame

or

not
chiseled

slant of latch

bolt faces
door frame

N (2x)

wood block

1. Remove plates.

A

Install strike on the door frame.

E

A

C

2. Install drive -in collar.

A3

1 / 4

P (2x)

door frame

Install the exterior keypad, mounting plate, and spindle

3

actual

size

T

Install exterior keypad.

A

cable goes
over latch

Route cable through mounting plate.

B

F

G

Install interior assembly

4

A B

a

Remove battery cover. Connec t cable.

M

b

Remove
battery
pack.

K

Secure mounting plate with

C

supplied screws.

keep parallel to

edge of door

D

Install spindle.

rounded edge
faces latch

T (2x)

tighten

screws

evenly

F2

latch

actual

size

U

Install interior assembly onto mounting plate.Remove battery cover and battery pack from interior assembly.

a

c

Install levers

5

Install interior lever.

A

Install 4 AA batteries into bat tery pack.

4x

Ensure correct polarity.

For best results, use
new, non-rechargeable
Alkaline batteries only.

Do not install

battery pack

into interior

assembly yet.

Secure interior lever.

B

b

Install
battery
pack.

L

Ensure tight cable connection.

c

Push interior assembly onto

K

Install exterior lever.

C

mounting plate.

Push excess
cable back into
the door as you
install L.

Tur nb ut ton
may need to
be turned to
install L.

L

Secure exterior lever.

D

d

Secure with
screws.

U (2x)

Lever handle
faces away
from the latch.

Y1 or Y2 Y1 or Y2

Test latch operation

6

Close door, test latch operation and make adjustments as needed:

The small bolt of the latch should not enter the strike
hole. If it enters the strike hole , reposition strike.

Tighten pre­installed set
screw.

Lever handle

faces away

from the latch.

Z Z

If latch is loose in the strike, adjust the strike tab so it
grips the latch bolt better when the door is closed.

Tighten pre­installed set
screw.

small bolt in

strike hole

small bolt NOT

in strike hole

tab

2 / 4

Add user codes (8 max)

7

Programming Timeout

If no button is pressed for ive se conds, the system will time
out and you will need to restart the procedure.

Make sure the door is open. Press

A B C

the Program button the number of
times that corresponds to the user
code position being programmed.

Example: If
programming
the third code,
press the button
three times.

What lights and sounds does the lock produce?

D

Enter user code. A total of 8 user
codes may be programmed.

Each user code must be

a unique code between

4 and 8 digits.

One green lash with one beep* Three red lashes with three beeps* Two beeps*

or or

green

1x 3x

red

Press Lock button once.

2x

Program ming was succes sful.

*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.

Mastercode

For enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming
and Troubleshooting Guide on the SmartCode 5 Lever page at w ww.weiserlock.com.

Test the lock (review normal operation)

8

Conirm that the code(s) added in previous step can unlock the door.

Locking the Door Unlocking the Door

Press Lock button once. Enter user co de.

Program ming was unsucce ssful.

Make sure th e user code is not a d uplicate and that i t is

betwee n 4 and 8 digits duri ng your next attem pt.

Program ming time out.

Make sure no t to pause for more tha n 5

seconds during programming.

Tip: You can press the
Lock button before
entering your user
code to light up the
keypad at night.

Re-key the lock (if needed) and install the battery cover

9

Re-key the lock (if needed). Install the battery cover.

A B

a a

IMPORTANT:
Remove battery
pack before
re-keying.

K

Re-key the lock to work with your

b b

existing key. See the supplied
SmartKey Re-key instructions
for more information.

c

Reinstall
battery
pack.

K

actual

size

V

M

V (2x)

H

3 / 4

Reference Guide

SmartCode at a Glance

Exterior

Keypad

SmartKey

tool hole

Lock
button

Keyway

Switches and Status LED colors

Interior (cover removed)

Back

panel

Program

button

Status

LED

Switches

Tur np ie ce

System Alerts

Alert Reason Solution

Keypad lashes red 1 time
with 1 beep*

Keypad lashes red 3 times
with 3 beeps*

Keypad lashes red 10
times with 10 beeps*

Lock beeps 2 times.

Keypad lashes red 3 times.

Keypad lashes red 6 times
with 6 beeps*.

Keypad lashes red 15 times
with 15 beeps*

*Beep ing sound will only b e heard if switch #3 is on.

Door jammed while
attempting to lock.

Unsuccessful programming.

One incorrect code entered. Re-enter code.

No user code programmed. Program at least one user code.

Low battery. Replace batteries.

Programming timeout.

Three incorrect codes entered
within one minute.

Manually re-lock door. If needed,
reposition strike.

Attempt programming procedure
again.

Attempt programming procedure
again, making sure not to pause for
more than 5 seconds.

Re-enter code after 60 second keypad
lockout.

Deleting a user code

Switches

O

On

1 2 3 4

Switch Function

Door lock status LED blinks every 6

1

seconds

Lock automatically re-locks door 30

2

seconds after unlocking. Disabled if no
codes are programmed.

3 Audio

4 Not used.

assembly when battery replacement is required.

Lock
above
lever

Battery
pack

Status

LED

Color Lock Status

Green Unlocked

Amber Locked

Red Low battery

In order to de lete a user code, you must override the code by adding a di erent user code in the s ame
position. For example, if you want to delete the third code, add a di erent user code in position three .

Test the old user code to make sure it can no longer unlock the door.

If you cannot remember the user code position, you may wish to perform a factory reset to delete all
codes associated with the lock .

Tr ou bl es h oo t in g

A complete Programming and Troubleshooting Guide is available on

the SmartCode 5 Lever page at www.weiserlock.com.

Factory ResetBattery Replacement

A factory re set will delete all codes associated with the lock.If another lock is installed above the lever, remove the interior

1 Remove

battery pack.

2 Press and HOLD the Program

button while reinserting
the battery pack.

Keep holding the but ton for 30

seconds until the lo ck beeps
and the status LED lashes red.

Status
LED

Interior
assembly

Important Safeguards

1. Read all instructions in their entirety.

2. Familiarize yourself with all warning and caution statements.

3. Remind all family members of safety precautions.

4. Protect your user codes and mastercode.

5. Dispose of used batteries according to local laws and regulations.

CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel

can change the user codes, you must restrict access to the back panel and routinely
check the user codes to ensure they have not been altered without your knowledge.
The use of a mastercode can help protect your system’s settings.

WARNING: This Manufacturer advises that no lock can provide complete security

by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualiied locksmith or other security professional.

Mounting
plate

3 Press the Program button

once more. When the LED
lashe s green an d you
hear one beep, the lock
has been reset.

4 Add user codes to your lock.

4 / 4

© 2016 Spectrum Brands, Inc.