Operating Instructions
Nameplate
The nameplate is located on the
back of the handheld remote
control (see Fig. Changing the
Battery).
Approved Use
The WeiTronic Remoto 1M hand-
held remote control is solely
designed for the purposes of
controlling sun protection systems such as lamella outdoor
blinds, roller blinds, and jointed
arm and vertical awnings.
Technical Specifications
Nominal voltage 3V DC
Battery type Coin cell 2430
Protection class IP 20
Ambient temperature –10°C to 55°C
Radio frequency 868.3 MHz
Dimensions 118 x 53 x 21 mm
Weight 80 g
Selecting the Operating Mode
• Manual operation: manual commands
such as , , are selected by pressing
the relevant button.
• Automatic operation: manual commands plus automatic sun control.
• To change the operating mode, press
the Select button (8) (for longer than
1 second.
• Changing from manual to automatic
operation will cause the products to
retract.
Transmission Check
The channel display doubles up as the
transmission check. Should a radio signal
be received, this will be signalised by
flashing. Should the battery performance
run down, the brightness of the display
will dim and the frequency range will
drop. If the control lamp stop flashing
when a button is pressed, the battery will
need to be replaced.
Automatic Wind Control
When there is a risk of high winds, the sun
protection system will retract and remain
shut down for approx. 15 minutes. Should
the or button be pressed during the
shutdown period, the product will move
very slightly to signal that the system is
still shut down. Please note: The automatic
wind control cannot be deactivated.
Lux and Tempura
Jointed arm awnings are also available as
extras with lighting (Lux) and heating
systems (Tempura).
• To activate these options, press the or
button (for less than 1 second).
• Hold the or button down to dim
the lighting.
• Press the button to switch off either
the lighting or the heating.
Handheld Remote Control
WeiTronic Remoto 1M
㛯㛯㛯
www.weinor.com
(1) Channel display
(2) Operating mode display:
Manual
Automatic
(3) Up On/Brighten*
(4) Stop Off*
(5) Down On/Dim*
(6) Rocker button Up
Brighten*
(7) Rocker button Down
Dim*
(8) Selection button for
operating mode
* Lux, Tempura
Operating Instructions
Power Setting (for Lux and Tempura)
A power setting is an arbitrary brightness
or heating setting. After programming,
this can be activated by pressing the or
button twice. Power settings can be
reprogrammed at any time.
How to programme the power setting
1. Set the level to maximum or minimum.
2. Hold down the or button for as
long as it takes to reach the desired
setting.
3. As soon as the desired setting is
reached, press the button as well.
4. The setting will stop and the power setting is programmed.
Cleaning
• Only ever clean the device using a dry
cloth.
• Never use any detergents as these can
damage the plastic.
Declaration of Conformity
weinor hereby certifies that the weinor
Remoto 1M handheld remote control is in
compliance with the material requirements and all other relevant provisions of
the Guideline R&TTE 1999/5/EC.
Area of Application
This device has been certified for use in
Switzerland and within the European
Union.
Using a suitable screwdriver, open the
back of the handheld remote control.
Remove the old battery and insert the new
battery (coin cell 2430) making sure that
the symbols match (“+” can be seen at the
top). Dispose of the old battery in an environmentally-friendly manner.
Replace the back plate and screw it down
onto the handheld remote control using a
screwdriver.
Changing the Battery
Troubleshooting
Error Cause Remedy
• The drive isn’t running; the trans- • The battery is low or • Insert a new battery
mission check display doesn’t flash has been inserted or the same battery
when a button is pressed. in the wrong way.
in the correct manner.
• The drive is running; the trans- • The battery is low. • Insert a new battery.
mission check display does not
run when a button is pressed.
• The drive isn’t running; the • The receiver is outside • Reduce the distance
transmission check display flashes the frequency range. to the receiver.
when a button is pressed.
• The desired drive isn’t • No mains supply • Connect the mains
running. (230 V). (230 V).
• The circuit breaker • Switch on the circuit
has been triggered. breaker.
㛯㛯㛯
㛯㛯㛯
weinor GmbH & Co. KG
Mathias-Brüggen Straße 110
50829 Cologne
Hotline: +49(0)221/5 97 09-214
Fax: +49(0)221/5 97 09-898
Subject to change without notice
www.weinor.com
Should you have any further queries, please contact your weinor specialist.
Translation of original instruction manual
Loading...