WAVESERIES
Signal Conditioners DC/DC CCC LP
without additional Voltage Supply
Type Cat. No.
Screw-type connection
1-channel WAS5 CCC LP 8444950000
2-channel WAS5 CCC LP 8463580000
Tension clamp connection
1-channel WAZ5 CCC LP 8444960000
2-channel WAZ5 CCC LP 8463590000
Read these instructions before using the product
and retain for future information.
9
1 General instructions
The WAVESERIES signal conditioner DC/DC CCC LP without additional voltage supply should only be installed by qualified staff
and should only be powered up following professional installation.
2 Application
The WAVESERIES signal conditioner DC/DC CCC LP without additional voltage supply are suitable for connection to 2-wire sensors. The signal is galvanically isolated and equally emitted as a 2wire signal. The voltage supply for input/output is generated from
the input-circuit.
3 Mounting and dismounting
Warning!! Mounting and dismounting may only be carried out
10
when the power supply has be disconnected. Failure
to observe will lead to considerable damage!
3.1 Mounting onto TS 35 DIN rails
(s. Fig. 1)
3.2 Pluggable electronic components for range alteration
(depending on model)
(s. Fig. 2)
1. Remove connector, (depending on model either screw-type or
tension clamp).
2. Press locking clips on both sides of the enclosure.
3. Pull out the circuit board.
Warning!! The circuit board can only be inserted in one position.
The connectors have been coded by the manufacturer, ensuring that they cannot be reversed.
3.3 Labelling possibilities
(s. Fig. 3)
WS 10 connector markers can be used to label module.
11
4 Electrical connection
(s. Fig. 4)
Example: 1-channel WAS5 CCC LP, Cat. No. 8444950000
(s. Fig. 5)
Example: 2-channel WAS5 CCC LP, Cat. No. 8463580000
5 Dimensions
(s. Fig. 6)
6 Notes on CE labelling of WAVESERIES modules
WAVESERIES modules, that carry CE-labelling, fulfil the requirements of the EU-Guidelines 89/336/EU "electromagnetic compatibility" and the therein listed harmonised European Norms (EN).
The declarations of conformity are, in accordance with the abovementioned EU-Guideline, Article 10, held at the following address
for the relevant authorities:
12
Weidmüller Interface GmbH & Co.
Postfach 3030
D-32720 Detmold
7 Technical data
Input
Input signal 0 ... 20 mA (4 ... 20 mA)
Input voltage, max. 18 V
Input current, max. 50 mA
Operating current < 100 µA
Voltage drop approx. 3 V at R
= 20 mA
at I
in
= 0 Ω
L
approx. 13 V at RL = 500 Ω
at I
= 20 mA
in
Output
Output signal 0 ... 20 mA (4 ... 20 mA)
Load resistance ≤ 500 Ω
Accuracy by Tu = 23 °C < 0.1 % from end value
Influence of the load resistance < 0.1 % from measurement per
100 Ω load resistance
Temperature coefficient 50 ppm/K from measured value
Response time 4.5 ms by 500 Ω burden
Remaining ripple < 20 mV
eff
Chopper frequency approx. 170 kHz
13
Coordination of Insulation according to EN 50178, 04.98
(Safe Distance)
Rated Voltage 300 V
Rated surge Voltage 6 kV
Overvoltage category III
Contamination class 2
Clearance and
creepage distances ≥ 5.5 mm
Isolation voltage
Voltage endurance
Input/output 4 kV
Input/output/to mounting rail 4 kV
/1 s
eff
/1 min
eff
Connection data
Connection BLZ/SL
Insulating stripping length 8 ± 0.5 mm
Solid core 0.5 ... 2.5 mm
Flexible core 0.5 ... 2.5 mm
With ferrules 0.5 ... 1.5 mm
2
2
2
14
EMC specification according to EN 55011,
class B, group 1
according to EN 50081-1
according to EN 50082-2
General
Operating temperature
mounted on DIN rails
without clearance -25 ... +70 °C
Storage temperature -40 ... +80 °C
Approvals CE, CSA, UL
15
8 Accessories
Terminal connector, 3-pole for screw-type connection
BLZ 5.08/3 SN OR
- orange 1526560000
- black 1526510000
Terminal connector, 3-pole for tension clamp connection
BLZF 5.08/3
- orange 1707470000
- black 1707700000
Connector markers
WS 10/5 Multicard for plotter labelling 1635010000
WS 10/5 blank 1060860000
In the interest of protecting the environment, return any spare
operating instructions to your local stockist for re-use.
Printed on chlorine-free bleached paper.
16
Loading...