Page 1
IIE
E--
SW5--E
E
C
C
O
O--
F
F
L
L
AT
The IE-SW5-ECO-FLAT switching hub is designed for the Industrial Automation
environment.
Like all Ethernet switches from Weidmüller, it features non-blocking (full wirespeed) operation. It divides an Ethernet network into five collision domains "bridging" data links to create larger network diameters than possible with
repeating hubs.
Each port automatically negotiates its data rate to 10 Mbps or 100 Mbps - controlling data flow with the PAUSE function in full-duplex links or with the backpressure method in half-duplex links.
Port assignments are learned by reading Ethernet frames and logging the
source addresses to a table. Throughput is improved by restricting traffic to
those ports party to a data exchange - while other data is simultaneously
exchanged on other ports.
Store-and-forward operation is implemented and broadcast, multicast, or unicast transmissions are received by all ports.
The IE-SW5-ECO-FLAT has five Auto-MDIX ports for attaching local devices.
In addition to a power LED, each port has one LED showing link/activity/rate
and one showing duplex status.
The unit operates from a wide range of low-voltage AC or DC power.
The IE-SW5-ECO-FLAT is provided with a writable label for easy identification
of the remote device attached to each cable.
Weidmüller t
INSTALLATIONGUIDE
Industrial Ethernet 10/100 Mbps Mini-Switch
Page 2
Compliance
CEFCC, part 15, Class A
EN50081-2
EN50082-2
SPECIFICATIONS
Electrical Functional
INPUT DC AC Compliance: ANSI/IEEE 802.3
Voltage: 10-36 V8-24 V Data Rates: 10 /100 Mbps
Power: 5 W 5 VA Signaling: 10BaseT and 100BaseTX
Frequency N/A 47-63Hz
Connectors: Shielded RJ-45
Temperature Segment Length: 100 m (max)
Operating Temperature: 0°C to +60°C LED- Indicators
Storage Temperature: -40 C to +85°C
Power green
Mounting Activityt/ Link green or yellow
Duplex green
DIN-rail TS-35
Pin Funktion
1 TD+
2 TD-
3 RD+
6 RD-
RJ45 Connector Pin Assignment
(All other pins are unused.)
DIMENSIONAL DRAWING
Page 3
POWER OPTIONS
Power Considerations
Voltage in the range of 10-36 VDC or 8-24 VAC must deliver current commensurate with 5-watt
power consumption. The recommended size for solid power conductors is 16-22 AWG; for stranded conductors, use 16-18 AWG. Ground is directly connected to zero volts and the chassis is
isolated from zero volts. Input connections are reverse-polarity protected.
Network Connections
The switch employs Auto-MDIX technology so that either straight-through or crossover cables can
be used to connect to network interface adapters or to another hub.
LED Indicators
The "PWR" LED glows solid green when the switch is properly powered. To aid in troubleshooting, each port has two LEDs. The Port 1 LED labeled "L" glows solid if a link exists, flashes to
show activity and shows data rate by color: green for 100 Mbps and yellow or 10 Mbps. The LED
labeled "D" glows solid green if full-duplex is on or is unlit when that port is operating in halfduplex mode. The LEDs of Ports 2-5 are unlabeled but work the same.
Page 4
WARRANTY FOR THIS PRODUCT
Weidmueller Interface GmbH & Co KG warrants this product to the original purchaser for five
year from the product’s shipping date. If a Weidmueller product fails to operate in compliance
with its specification during this period, Weidmueller will, at its option, repair or replace the product at no charge. The customer is, however, responsible for shipping the product; Weidmueller
assumes no responsibility for the product until it is received. This warranty does not cover repair
of products that have been damaged by abuse, accident, disaster, misuse,or incorrect installation. Weidmuellers limited warranty covers products only as delivered. User modification may void
the warranty if the modification damages the product, in which case this warranty does not cover
repair or replacement.
This warranty in no way warrants suitability of the product for any specific application.
Manufacturer:
Weidmüller Interface GmbH & Co. KG
Klingenbergstrasse 16
32758 Detmold
Germany
DECLARATION OF CONFORMITITY
EMC Directive 89/336/EEC as amended by 92/31/EEC & 93/68/EEC; General Product
Safety Directive 92/59/EEC
EN 55022:1995 (CISPR22: 1993), Class A; EN 50082-2:1995, EMC - Part 2: Industrial
Environment
Loading...