Weider WESY59931 Owner’s Manual

Model No. WESY5993 Serial No.

Write the serial number inthe space above for future reference.

Serial Number Decal (under seat)

QUESTIONS?

As a manufacturer, we are com- mitted to providing complete

customer satisfaction. If you have questions, or if a pert is

damaged or missing, PLEASE CONTACT OUR CUSTOMER

SERVICE DEPARTMENT DIRECTLY.

byWEIDER

CALLTOLL-FREE:

1-877-992-5999

Mon,-Fri., 6 a.m._ p.m. MST

ON THE WEB: www.weiderservice.com

_LCAUTION

USER'S MANUAL

Read all precautions and instruc- tions inthis manual before

using this equipment. Save this manual for future reference.

www.weiderfitness.com

new products, prizes,

fitness tips, and much more!

TABLE OF CONTENTS

WARNING DECAL PLACEMENT ............................................................. 2

IMPORTANT PRECAUTIONS ................................................................ 3

BEFORE YOU BEGIN ...................................................................... 4

ASSEMBLY ............................................................................... 5

ADJUSTMENTS .......................................................................... 13

CABLE DIAGRAM ......................................................................... 16

EXERCISE GUIDELINES .................................................................. 17

ORDERING REPLACEMENT PARTS .................................................. Back Cover

LIMITED WARRANTY .............................................................. Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of

this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin-

ning assembly.

WARNING DECAL PLACEMENT

The decals shown here have been

placed on the resistance system. If a decal is missing or illegible, call the toll=free telephone number on the front

cover of this manual and order a free

replacement decal. Apply the decal in the location shown.

hands and

ngers clear of

area.

Read user's manual and follow all warnings

and operating instructions prior to use.

I isuse of this product may result in serious injury. I

Do not allow children on or around machine. Replace label if damaged, illegible, or removed. J

MAX by WELDER is a trademark of ICON IP, Inc.

iMPORTANT PRECAUTIONS

kWARNING: Toreducetheriskofseriousinjury,readthefo.owingimportantpreoautions

before using the resistance system.

1. Read all instructions in this manual and all 12. When adding resistance, both ends of the warnings on the resistance system before resistance bars must rest under the two "U'- using the resistance system. Use the resist- channels. Add and remove resistance bars ante system only as described in this manual, from the "U'-channels one resistance bar at

a time.

2. It is the responsibility of the owner to ensure that all users of the resistance system are 13. Keep clear of the area around the "U'-chan-

adequately informed of all precautions, nels while the resistance system is in use.

Do not add or remove resistance bars from

3. The resistance system is intended for home the "U'-channels while the end of the long use only. Do not use the resistance system in cable is pulled out. any commercial, rental, or institutional setting.

14. Always adjust the resistance bar assembly to

4. Keep the resistance system indoors, away the horizontal position and make sure the from moisture and dust. Place the resistance fulcrum knob is secure before using the

system on a level surface, with a mat resistance system. beneath it to protect the floor or carpet. Make sure that there is enough clearance around 15. Make sure the rings on the resistance bars the resistance system to mount, dismount, are pushed against the tray before using the

and use the resistance system, resistance system.

5. Inspect and properly tighten all parts regular- 16. If you purchase the optional fat bar, always

ly. Replace any worn parts immediately, disconnect it from the short cables when per-

forming an exercise that does not require it.

6. Keep children under 12 and pets away from

the resistance system at all times. 17. Make sure the storage knob is in place and

fully tightened each time the resistance sys-

7. Keep hands and feet away from moving parts, tern is used.

8. Always wear athletic shoes for foot protec- 18. Pull on the low pulley cable only while sitting lion while exercising, on the bench or standing on the base plate.

Pull on the high pulley cables only while sit-

9. The top frame is not designed to be used for ling on the bench, with the seat in one of the pull-up exercises. Do not hang on the top three positions closest to the upright base,

frame, or while standing on the base plate.

19.

10. The resistance system is designed to sup- port a maximum user weight of 300 pounds.

11. The resistance system is designed to be used with the included resistance, and the MAX PACK. Do not use the resistance sys- tem with any other type of resistance.

Make sure that the cables remain on the pul- leys at all times. If the cables bind as you are exercising, slop immediately and make sure that the cables are on the pulleys. Replace all cables at least every two years

20. if you feel pain or dizziness while exercising, stop immediately and begin cooling down.

.LWARNING: Beforebeginningthisoranyexerciseprogram,consu,yourphysician.This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

BEFORE YOU BEGIN

Thank you for selecting the innovative MAX by WELDER" LEGEND resistance system. The resistance system offers a selection of stations designed to devel- op every major muscle group of the body. Whether your goal is to tone your body, build dramatic muscle size and strength, or improve your cardiovascular system,

the resistance system will help you to achieve the spe-

cific results you want.

For your benefit, read this manual carefully before using the resistance system. If you have questions after reading this manual, see the front cover of this

ASSEMBLED DIMENSIONS: Height: 82 in. / 208 cm

Width: 66 in. / 168cm Depth: 80 in. / 203 cm

Fulcrum Knob

manual. To help us assist you, please note the product model number and serial number before calling. The

model number is WESY5993.3. The serial number can be found on a decal attached to the resistance system

(see the front cover of this manual).

To avoid a registration fee for any service needed under warranty, you must register the resistance system at www.weiderservice.com/registration.

Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.

Top Frame

Lat Tower

High Pulley

Resistance

Bars

Upright

Storage Knob

Backrest

Seat Knob

Leg Lever

J"-Channel

Foot Plate

Low Pulley Base Plate

Seat

ASSEMBLY

Make Things Easier for Yourself

• Tighten all parts as you assemble them, unless instructed to do otherwise.

This manual is designed to ensure that the resist- ance system can be assembled successfully by most people. However, it is important to realize

that the versatile resistance system has many

parts and that the assembly process will take time. Most people find that by setting aside plenty of time, assembly will go smoothly.

Before beginning assembly, carefully read the following information and instructions:

o Assembly requires two persons.

Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.

For help identifying small parts, use the PART IDENTiFICATiON CHART. Note: Some small

parts may have been pre-attached for shipping. If a part is not in the parts bag, check to see if it

has been pre-attached.

, As you assemble the resistance system, make

sure all parts are oriented as shown in the draw- ings.

The included Allen wrench and the follow- ing tools (not included) are required for assem=

bly:

Two adjustable wrenches One rubber mallet One standard screwdriver

, One Phillips screwdriver

Lubricant, such as grease or petroleum jelly, and soapy water.

Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

Beforebeg nn ogassembly,makesurethat

you have read and understand the informa-

tion in the box above. ..........................................

Press two 50mm Square Inner Caps (98) into the Base (1).

Attach two Plastic Feet (53) and two Large Plastic Feet (102) to the Base (1) with four M4 x 16mm Screws (62).

Attach the Upright (3) to the Base (1) with two M10 x 66mm Carriage Bolts (83), two M10 x 72mm Bolts (64), and four M10 Nylon Locknuts (76) as shown. Note: This step will be easier to complete if the Upright and Base are tipped

on their sides.

,_----102

k---62

Attach a Wheel (31) to the outside of the Base (1) with an M10 x 108mm Bolt (81), three M10 Washers (75), and an M10 Nylon Locknut (76). Do not overtighten the Locknut; the Wheel must be able to turn easily.

Attach the other Wheel (not shown) in the same manner.

Press a 38mm x 64mm Inner Cap (41) into each end of the Cross Tube (11).

Orient the Cross Tube (11) as shown, with the welded tubes at the bottom. Attach the Foot Plate

(23) and the Cross Tube to the Upright (3) with

two M10 x 140mm Carriage Bolts (73), two M10

Washers (75), and two M10 Nuts (47). Do not insert a bolt into the top hole in the Foot Plate

yet.

Press two 57ram Round Outer Caps (27) onto the ends of the Front Leg (6).

Orient the Bench Rail (5) as shown. Slide the Rail Bracket (105) into the indicated end of the Bench Rail, and align the holes in the Bracket with the

holes in the Bench Rail.

Orient the Front Leg (6) as shown. Attach the Front Leg to the Bench Rail (5) with the Rail Bracket (105), four M8 x 25mm Button Screws (46), and four M8 Split Washers (52).

75 47

Welded

Tube

See the inset drawing. Snap the Seat Knob (45) into the Seat Carriage (12) and attach it with two M6 x 16ram Screws (82) and two M6 Black Nylon Locknuts (69), Make sure the slot in the Knob is aligned with the slot in the Seat Carriage.

Orient the Seat (13) and Seat Backing (9) as shown. Attach the Seat and Seat Backing to the Seat Carriage (12) with four M6 x 16mm Screws (82).

Round

End

82 45 69

Pull the Seat Knob (45, not shown) out as far as it will go, and slide the Seat Carriage (12) onto

the Bench Rail (5). Engage the Seat Knob into the third hole from the end of the Bench Rail.

See the inset drawing. Attach a Hook (104) to

the bottom of the Bench Rail (5).

Third

Hole

Press the two Rail Inner Caps (99), with the wide ends on the top or bottom (as indicated), into the ends of the Bench Rail (5). Attach the Caps with

four M4 x 16mm Screws (62).

Locate the Leg Lever Cable (32), which has three ends connected in the middle with a bracket.

Route the end of the Cable with the eyebolt under a "V"-pulley (92). Attach the "V"-pulley to the Front Leg (6) with an M10 x 107mm Bolt (97) and an M10 Nylon Locknut (76). Slide the other two ends of the Cable onto the Hook (104).

Attach the Bench Rail (5) to the Upright (3) with an M10 x 132mm Bolt (66), a 19mm Spacer (17), a 22mm Spacer (106), and an M10 Nylon Locknut (76). Fully tighten the Storage Knob (30) into the Upright and Rail.

Wide

Eyebolt

62 12

92 32

99 Wide

97 ,End

1O4

Attach the Lat Tower (4) to the Upright (3) with four M10 x 25mm Button Head Screws (87) and four M10 Split Washers (103).

Attach the Name Plate (89) to the Lat Tower (4)

with two M4 x 16mm Screws (62).

103 87

103

Press two 38mm Round Inner Caps (38) into the

ends of the Top Frame (10).

Attach two Eyebolts (34) to the Top Frame (10)

with two M8 Washers (59) and two M8 Nylon

Locknuts (65). Do not overtighten the Locknuts; the Eyebolts must be able to rotate freely,

Attach the Top Frame (10) to the Lat Tower (4)

with two M10 x 65mm Button Head Screws (70), two M10 Washers (75), and the Top Frame Cover

(93). Make sure that the Eyebolts (34) are ori-

ented as shown in the inset drawing. If they

are not, turn the Top Frame around and reat- tach it.

¢/ 59

10. Attach the two 10-pound Short Caps (20) to the 10-pound Center Resistance Bar (44) with two M4 x 12mm Flat Head Screws (85).

Using ten M4 x 12mm Flat Head Screws (85), attach the two 10-pound Caps (101) to the 10- pound Removable Resistance Bar (67), the two 20-pound Caps (88) to the 20-pound Removable Resistance Bar (36), the four 80-pound Caps (100) to the two 80-pound Resistance Bars (95), and the two 40-pound Caps (79) to the 40-pound Resistance Bar (96).

11.

Locate the Fulcrum (18) on the Lat Tower (4) (see

the inset drawing). Slide the Tray (35) onto the

rods on the Fulcrum. Make sure the Tray is ori- ented as shown in the drawing.

Set the Resistance Bars into the Tray (35) in the

following order: the 10-pound Removable

Resistance Bar (67), the 20-pound Removable Resistance Bar (36), an 80-pound Resistance Bar (95), the 10-pound Center Resistance Bar (44), an 80-pound Resistance Bar (95), and the 40-pound Resistance Bar (96). Make sure the indicated rings are on the side shown and the arrows point toward the Tray.

Attach the Cover Plate (72), with the edges up, to

the Tray (35) with two M8 x 19mm Button Head

Screws (86).

Rings on

this side

Rods

+ 16 hidden pages