Weider WEBE09910 User Manual
QUESTIONS?
As a manufacturer, we are committed to providing complete customer
satisfaction. If you have questions,
or if there are missing parts, we will
guarantee complete satisfaction
through direct assistance from our
factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians
on our customer hot line will provide immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WEBE09910
Serial No.
Write the serial number in the space
above for reference.
CAUTION
Read all precautions and instructions
in this manual before using this
equipment. Save this manual for
future reference.
Serial Number
Decal
USER’S MANUAL
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Patent Pending
Adjusting the Press Plate
To adjust the distance
between the Small Seat
(29) and the Press Plate
(6), remove the Adjustment
Pin (26) from the Base (2).
Slide the Adjustment Frame
(3) into or out of the Base
until the Press Plate is in
the correct position. Insert
the Adjustment Pin into the
indicated hole in the Base and a hole in the Adjustment
Frame.
This section explains how the body toning system can be adjusted. Inspect and tighten all parts each time you use the
body toning system. Replace any worn parts immediately. The body toning system can be cleaned with a damp cloth
and a mild, non-abrasive detergent. Do not use solvents.
Adjusting the Resistance
To change the amount of
resistance, remove the four
Spring Clips (5) from the
bench. Attach the 25-lb.
Bands (25) to the bars on
the Base (2) and the Pivot
Frame (7). Secure the
Bands with the four Spring
Clips.
The 10-lb. Bands (28) can be attached in the same manner. Attach both sets of Bands for maximum resistance.
WARNING: Always place an equal
amount of resistance on each side of the body toning system.
WARNING: To reduce the risk of serious injury, read the following important precautions before
using the body toning system.
1. Read all instructions in this manual before using
the body toning system. Use the body toning
system only as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the body toning system are adequately informed of all precautions.
3. The body toning system is intended for home
use only. Do not use the body toning system in a
commercial, rental or institutional setting.
4. Use the body toning system only on a level surface. Cover the floor beneath the body toning
system for protection of the floor.
5. Inspect and tighten all parts each time you use
the body toning system. Replace any worn parts
immediately.
6. Keep children under 12 and pets away from the
body toning system at all times.
7.
If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling
down.
8. Keep hands and feet away from moving parts.
9. Always make sure there is an equal amount of
resistance on each side of the body toning system.
10. The body toning system is designed to support a
maximum of 250 pounds.
11. Always wear athletic shoes for foot protection
while exercising.
WARNING: Before beginning this or any exercise program, consult your physician. This is
especially important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage sustained
by or through the use of this product.
5
26
2
3
6
29
2-Bar
7-Bar
25
Adjusting the Body Toning System
Important Precautions
Thank you for selecting the versatile WEIDER®TWO
TONE body toning system. The TWO TONE body toning
system is designed to help you develop every major muscle group of the body. Whether your goal is a shapely figure, dramatic increase in muscle size and strength, or a
healthier cardiovascular system, the TWO TONE body toning system will help you achieve the specific results you
want.
For your benefit, read this manual carefully before
using the WEIDER
®
TWO TONE body toning system. If
you have additional questions, please call our Customer
Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please mention the
product model number (WEBE09910) and the serial number found on a decal attached to the body toning system
(see the front cover of this manual).
1.Press two 2” Round
Outer Caps (23) onto
each of the two Front
Stabilizers (9) and
the two Rear
Stabilizers (not
shown).
Attach a Front Stabilizer (9) to the Ab Leg (12) with two
5/16” x 2 1/2” Carriage Bolts (31) and two 5/16” Nylon
Locknuts (34).
Attach a Rear Stabilizer (not shown) to the other end of
the Ab Leg (12) in the same manner. Note: The Front
Stabilizers (9) are shorter than the Rear Stabilizers.
2.Insert a 5/16” x 3”
Carriage Bolt (32)
into the center hole in
the Large Support
Plate (14). Attach the
Large Support Plate
to the Large Seat
(13) with two 1/4” x
3/4” Screws (40).
Press a 1” x 2” Inner
Cap (30) into the
lower end of the Seat
Frame (15).
Insert a 5/16” x 3” Carriage Bolt (32) into the indicated
hole in the Seat Frame (15). Insert the 5/16” x 3”
Carriage Bolt in the Large Support Plate (14) through
the rear hole in the Seat Frame.
Attach the Large Seat (13) to the Seat Frame (15) with
the 1/4” x 1/2” Screw (39).
Secure the two 5/16” x 3” Carriage Bolts (32) to the Ab
Leg (12) with two 5/16” Washers (35) and two 5/16”
Nylon Jamnuts (46).
1
3.Hold the Metal
Bushing (27) inside
the Seat Frame (15).
Slide a 5/16” x 1 3/4”
Bolt (33) into the
upper hole in the Ab
Frame (11), the Seat
Frame, and the Metal
Bushing.
Slide another 5/16” x
1 3/4” Bolt (33) into
the lower hole in the
Ab Frame (11) and the Seat Frame (15).
Secure the two 5/16” x 1 3/4” Bolts (33) with two 5/16”
Washers (35) and two 5/16” Nylon Locknuts (34).
Press a 1” x 2” Inner Cap (30) into the upper end of the
Seat Frame (15).
4.Remove the 1/4” x
3/4” Type F Screws
(47) from the Ab
Frame (11). Attach
the Ab Handlebars
(10) to the Ab Frame
with the two 1/4” x
3/4” Type F Screws.
Press a 1 1/8” Round
Inner Cap (16) into
each Ab Handlebar
(10).
Wet the Ab
Handlebars (10) and the Ab Frame (11) with soapy
water. Slide a Short Cover Sleeve (48) onto each side
of the Ab Frame. Slide a Long Cover Sleeve (17) onto
each Ab Handlebar.
2
3
11
33
23
23
34
12
34
31
13
15
14
32
32
40
12
39
40
30
46
35
9
35
34
30
15
27
4
10
10
11
16
47
17
48
47
16
Before You Begin
Assembly—Ab Tilt & Tone
Loading...