Weider 831.150460 User Manual

Page 1
Model No. 831.150460 Serial No.
PATENT PENDING
The serial number can be found in the location shown below. Write the serial number in the space above.
CAUTION
Read all precautions and instruc­tions in this manual before using this equipment. Save this manual for future reference.
USER'S MANUAL
Serial Number Decal (under
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
Page 2
2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ADJUSTING THE WEIDER PRO 120 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
FULL 90 DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
IMPORTANT PRECAUTIONS
WARNING:To reduce the risk of serious injury, read the following important precautions before using the weight bench.
1. Read all instructions in this manual before using the weight bench.
2. Use the weight bench only as described in this manual.
3. Use the weight bench only on a level surface. Cover the floor beneath the weight bench for protection.
4. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
5. Keep small children and pets away from the
weight bench at all times.
6. Always wear athletic shoes for foot protec-
tion while exercising.
7. The weight bench does not include weights. The weight bench is designed to support a maximum of 250 pounds, including the user and weights.
8. When using the weight bench, make sure that the lock pins are fully inserted and are turned to the locked position.
9. If you feel pain or dizziness at any time while exercising, stop immediately and begin cool­ing down.
10. It is the responsibility of the owner to ensure that all users of the weight bench are ade­quately informed of all precautions.
WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. SEARS assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
Page 3
3
BEFORE YOU BEGIN
Backrest
Lock Pins
Adjustment Leg
Pivot Leg
Thank you for selecting the WEIDER®PRO 120 Weight Bench. The PRO 120 Weight Bench is designed to be used with your own weights (not included) to develop several muscle groups. Whether your goal is a shapely figure, dramatic muscle size and strength, or a healthier cardiovascular system, the PRO 120 Weight Bench will help you to achieve the specific results you want.
For your benefit, read this manual carefully before using the WEIDER®PRO 120 Weight Bench. If you
have additional questions, please call our toll-free
HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the prod­uct model number and serial number before calling. The model number is 831.150460. The serial number can be found on a decal attached to the PRO 120 Weight Bench (see the front cover of this manual).
Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.
Foam Pads
Foam Pads
Page 4
4
ASSEMBLY
Before beginning assembly, carefully read the following information and instructions:
• Place all parts in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed.
• Read each assembly step before you begin.
• For help identifying the small parts used in assembly, use the part identification chart below. The number in parenthesis below each part refers to the key number of the part. The second number refers to the quantity needed for assembly. Note: Some small parts may have
been pre-attached for shipping purposes. If a part is not in the parts bag, check to see if it has been pre-attached.
• Tighten all parts as you assemble them, unless instructed to do otherwise.
• During assembly, make sure that all parts are ori­ented as shown in the drawings.
THE FOLLOWING TOOLS (NOT INCLUDED) ARE REQUIRED FOR ASSEMBLY:
• Two (2) adjustable wrenches
Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.
M10 x 68mm Bolt (14)–1
38mm x 38mm Inner Cap (16)–1
M6 x 48mm Bolt (4)–2
M6 x 16mm Bolt (5)–2
3/4" Round Inner Cap (7)–4
M10 Nylon Locknut (13)–1
38mm x 50mm Inner Cap (8)–1
50mm Round Outer Cap (9)–4
Page 5
1. Before beginning assembly, be sure that you
have read and understand the information on the previous page.
Press a 38mm x 38mm Inner Cap (16) into the end of the Frame (1). Press Two 50mm Round Outer Caps (9) onto the Adjustment Leg (3). Press a 38mm x 50mm Inner Cap (8) into the end of the Adjustment Leg.
Align the indicated holes in the Frame (1) and the Adjustment Leg (3). Attach the Adjustment Leg to the Frame with two Lock Pins (11).
2. Align the indicated holes. Attach the Pivot Leg (2) to the Frame (1) with the M10 x 68mm Bolt (14) and the M10 Nylon Locknut (13).
Secure the Pivot Leg (2) by inserting the “L” Pin (15) through the indicated hole in the Pivot Leg and the corresponding hole in the Frame (1).
Press Two 50mm Round Outer Caps (9) onto the Pivot Leg (2).
3. Press 3/4” Round Inner Caps (7) into the ends of both Pad Tubes (10).
Insert the Pad Tubes (10) through the Adjustment Leg (3).
Slide Foam Pads (6) onto the ends of both Pad Tubes (10).
4. Attach the Bench (12) to the Frame (1) with two M6 x 48mm Bolts (4) and two M6 x 16mm Bolts (5).
4
1
1
8
16
11
9
3
2
3
5
1
13
2
9
14
Align these
Holes
Align these
Holes
3
12
1
5
4
10
7
6
7
6
15
Page 6
ADJUSTING THE PIVOT LEG
To change the position of the Pivot Leg (2), remove the “L” Pin (15). Align the other set of holes in the Pivot Leg and the Frame (1). Re-insert the “L” Pin.
ADJUSTING THE LEVEL OF THE BENCH
To change the level of the Bench (12), remove both Lock Pins (11) from the Frame (1) and Adjustment Leg (3). Align the set of holes in the Frame with another set of holes in the Adjustment Leg. Re-insert the Lock Pins.
Always use both Lock Pins.
ADJUSTING THE WEIDER PRO 120
The weight bench is designed to be used with your own weights (not included). The steps below explain how the weight bench can be adjusted. Refer to the accompanying exercise poster for exercise information.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
2
1
1
15
11
12
3
6
Page 7
4
12
1
11
5
16
13
2
9
9
15
14
9
3
9
6
7
10
7
6
7
6
8
PART LIST and R0996A EXPLODED DRAWING—Model No. 831.150460
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts.
Key Part
No. Qty. No. Description
1 1 132209 Frame 2 1 132504 Pivot Leg 3 1 132506 Adjustment Leg 4 2 111855 M6 x 48mm Bolt 5 2 132137 M6 x 16mm Bolt 6 4 103805 Foam Pad 7 4 112402 3/4” Round Inner Cap 8 2 132142 38mm x 50mm Inner Cap 9 4 100290 50mm Round Outer Cap
Key Part
No. Qty. No. Description
10 2 132148 Pad Tube 11 2 132505 Lock Pin 12 1 132210 Bench 13 1 012033 M10 Nylon Locknut 14 1 111084 M10 x 68mm Bolt 15 1 105977 “L” Pin 16 1 103833 38mm x 38mm Inner Cap
# 1 132207 User’s Manual # 1 132208 Exercise Poster
7
Page 8
Part No. 132207 R0996A Printed in China © 1996 Sears, Roebuck and Co.
Model No. 831.150460
QUESTIONS?
If you find that:
• you need help assembling or operating the WEIDER®PRO 120
• a part is missing
• or you need to schedule repair service
call our toll-free HELPLINE
1-800-736-6879
Monday–Saturday, 7 am–7 pm Central Time (excluding holidays)
REPLACEMENT PARTS
If parts become worn and need to be replaced, call the following toll­free number
1-800-FON-PART (1-800-366-7278)
The model number and serial number of your WEIDER®PRO 120 are listed on a decal attached to the frame. See the front cover of this manual to find the location of the decal.
All replacement parts are available for immediate purchase or special order when you visit your nearest SEARS Service Center. To request service or to order parts by telephone, call the toll-free numbers listed at the left.
When requesting help or service, or ordering parts, please be pre­pared to provide the following information:
• The MODEL NUMBER of the product (831.150460).
• The NAME of the product (WEIDER®PRO 120).
• The PART NUMBER of the PART (see the PART LIST and the EXPLODED DRAWING on page 7 of this manual).
• The DESCRIPTION of the PART (see the PART LIST and the EXPLODED DRAWING on page 7 of this manual).
FULL 90 DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this SEARS WEIGHT BENCH EXERCISER, contact the nearest SEARS Service Center throughout the United States and SEARS will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Loading...