WE-EF FLC200 LED, FLC240 LED, FLC230 LED, FLC260 LED, FLC220 Installation And Maintenance Instructions

WE-EF LIGHTING

Thailand
Tel [phone]
Fax [phone]
[e-mail]

WE-EF LIGHTING

Australia
Tel [phone]
Fax [phone]
[e-mail]

WE-EF LIGHTING

United States of America
Tel [phone]
Fax [phone]
[e-mail]

www.we-ef.com

WE-EF LEUCHTEN

Germany
Tel [phone]
Fax [phone]

[e-mail]

WE-EF LUMIERE

France
Tel [phone]
Fax [phone]

[e-mail]

WE-EF HELVETICA

Switzerland
Tel [phone]
Fax [phone]

[e-mail]

WE-EF LIGHTING

United Kingdom
Tel [phone]
Fax [phone]

[e-mail]

INSTALLER

HOTLINE

[phone]

7am – 7pm AEST

WE-EF LEUCHTEN

Installation and

Maintenance Instructions for

Projectors

FLC200 LED Series

INSTALLER

HOTLINE

[phone]

7am – 7pm AEST

FLC200 LED_280618 / 006-1348-OZ

Technical specifications are subject to change.
© WE-EF 2018

Safety Notice

The manufacturer is discharged from liability when damage is
caused by improper use or installation.

If any luminaire and/or accessory is modified from that supplied by
WE-EF, the persons responsible for the modification shall be
considered as manufacturer.

Projectors

FLC240: . . . . . . . . . . . . . . . . . . . 24 LED 48W / 72W / 104W

FLC260: . . . . . . . . . . . . . . . . . . 36 LED 72W / 108 W / 155W

B

F

C

E

A

H

G

D

160

145

ø 260

70

ø 18

ø 14

44

165

190

ø 340

70

ø 18

ø 14

44

175

195

ø 385

60

44

ø 18

ø 14

FLC240

FLC260

FLC240: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,090 m²

FLC260: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,116 m²

FLC240: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . max. 13,8 kg

FLC260: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . max. 18.8 kg

ø 5,5 – 12 mm

0,14 – 2,5 mm

2

DMX-Power

M4 max. 2,0 Nm
M5 max. 4,0 Nm
M6 max. 6,0 Nm
M8 max. 15,0 Nm
M16 max. 100,0 Nm

FLC230

Lamps

FLC230:

. . . . . . . . . . . . . . . . . . . . 12 LED 24W / 36W / 52W

Protection: IP66,
IK08 (PMMA), IK06 (Safety glass lens)

Class I, ta = 25°C

Windage area

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,054 m²

FLC230:

Weight:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . max. 9,1 kg

FLC230:

Maintenance

Apart from cleaning the product’s exterior surfaces, no
special maintenance work is required. Clean only with a

cloth and water

Do not use high-pressure cleaners.

Protect our environment: Discard used LEDs in compliance
with the most recent environmental legislation.

Torque

Screw Torque

Tools required

– Screwdriver TX 25
– Screwdriver TX 40
– Screwdriver with blade 3x1
– Screwdriver TX70

Installation

The product must be installed and maintained by a suitably
qualified professional in compliance with latest building/
construction and/or electrical regulations and relevant
legislation.

Warning: Switch off and isolate mains electrical supply
prior to installing and connecting the luminaire. Do not open
the luminaire while mains supply is switched on.

Notice: If the luminaire is modified by anybody other than
the original manufacturer, then the warranty will no longer
be valid and shall become the full responsibility of the
modifying person/organisation. Claims based on defects
attributable to improper installation and/or application, and
the consequences thereof, are excluded.

In case of component failure due to abnormal circumstances
or at end of life, replacement must be carried out by a suit­ably qualified and trained professional.

ON-OFF7/7ADVANCED

BASIC

1-10V

DMX

DALI

Wiring Diagram

WE-EF Eco Step Dim® Advanced and

Shield

Da

Da

non dimmable luminaires

Class I Phase to L1, Neutral to N and Earthing to

WE-EF Eco Step Dim® Basic

Class I Phase to L1, Control Phase to L2

,

Neutral to N and Earthing to

Installation Procedure

1) Prior to electrical connection, proceed with mechanical

installation by firmly fixing stirrup A to optional mounting

accessory or directly to a suitable surface.
Aim luminaire.
Caution: Make sure not to damage any electric cable,

water pipe or other devices while drilling holes.

2) Switch off and isolate the mains electrical supply.

3) Remove gear box cover B by releasing screws C.

4) Check that rating shown on the luminaire label conforms

with the mains electrical supply.

5) Feed suitable mains supply cable D through cable gland

E. An additional gland is supplied to allow loop through

of supply cabling or alternative DMX cabling

arrangements

6) Connect to the correspondingly marked contacts of

terminal F, according to the wiring diagram.
Tighten cable gland E firmly.

1-10V / DALI / WE-EF Eco Step Dim® Dynamic

Class I  Phase to L1, Neutral to N and Earthing to ,

1-10V, DALI, DMX to

+ and 1-10V, DALI, DMX to –

7) Reposition gear box cover B and tighten screws C evenly.

8) Loosen the two screws G slightly. Aim luminaire in

desired direction, tighten screws G firmly (100Nm).
In addition, tighten screw H to secure orientation of
luminaire.

Notice: In case the luminaire is equipped with an optionally
available surge protector, the function can get tested if the
signal LED is lit green when the supply voltage is turned on.

In case the surge protector is defective, the LED device gets
automatically disconnected fr

om the mains supply.

If the signal LED is not lit, the luminaire is not functioning.