Internet of
. For different lines like xDSL,
page in WebGate
Quick Reference Guide of WebEye B101
This information is to connect WebEye B101 on
dedicated line or local LAN
cable and ISDN, please visit Download
Internet homepage and download related information.
http://www.webgateinc.com
WebGate Inc.
I. Monitoring of real-time image s through WebEye B101
PC Desktop, right click
high
or
above’.
or above.
2. Select ‘Settings ’.
and
configure settings for
Network
. Scroll down to
1. PC and LAN requirements
1.1 PC requirements
l CPU: Pentium II and above
l RAM: 64MB and above
l O/S: Windows 98/NT/Me/2000
1.2 Check display setting in your PC.
1. Go to
the mouse on the background.
Scroll down to “Properties”
3. Set color at ‘
color (16bit)’
4. Set resolution at
‘1024x768 pixels’
1.3 Check Network Setting for PC.
2
‘Properties’.
1 Right click the ‘
Neighborhood’ icon.
5. Click ‘OK’ button.
3 Scroll down to
‘TCP/IP ’
Ethernet card.
. Click on ‘Properties’
4
6. Check gateway address.
. Check IP
address and subnet
mask.
1. Connect Dome camera
2. Check the left DIP switch up
that indicates video terminated
resistor.
5. Go to ‘Gateway’.
1.4 Internet Browser Requirements
l Internet Explorer 5.0 and above
l Netscape Navigator 4.7 and above
1.5 Check LAN
l The WebEye should be connected to a
network configuration.
8
10 Base -T LAN
7. Go to ‘IP Address ’
. 10 Base-T LAN is standard for
l In the rare instance of 100 Base-T LAN, a 10/100 switching hub will be needed to
convert 100 Base T to 10 Base T.
2. Connecting Ethernet and Power Cables to WebEye.
2.1 Connect network and power to WebEye
l Make sure that indicator lights and dipswitches are as follows:
to input channel
Connect WebEye to a
HUB
Direct cable
Local User
Remote User
Router
Dedicated line, xDSL line, cable
modem line, ISDN line, and PSTN
(telephone) line are available.
blink
2 seconds
yellow LED
6 seconds and then
go off. This LED starts to blink when
The power input
jack. Use the included
3.
Connect LAN
When you connect cable to terminal block, you should peel off the cover of cable by 1.5Cm
ock.(communication., sensor, alarm and etc) In
cable (RJ -45).
4.
12-volt power adapter.
6. After receiving power,
should go on for 5-
user accesses WebEye
5. The green LED should
every 1-2 second (s) 1after receiving power.
Note in connecting cable to terminal block
and insert the cable by 2Cm into the terminal bl
case of power cable, the white mark of two lines means ‘+ ’.
Total length to insert in Terminal Block = 2cm
0.5cm
Covered
1.5cm
Peeled
2.2 Connect WebEye and a PC with Network Cable.
l To connect WebEye on Internet or LAN. With this connection remote user may not
access WebEye before local user configure its network setting.
Internet
PC through a HUB
l To directly connect WebEye to a PC, use the red crossover cable. This connection is just
A HUB
)
Connect WebEye directly
to a PC through LAN ports.
to configure WebEye.
* Crossover Cable and Direct Cable *
The crossover cable (red) provided with the WebEye is used to connect the WebEye with a PC.
is not necessary to connect the WebEye to a PC if a crossover cable is used. The direct cable (white
should be used if a HUB is used as an intermediary between the WebEye and PC.
3. Install WebEye Setup program in your PC
l
Copy WebEyeSetup.exe file from the enclosed CD (or Diskette).
l Paste the file into your PC
l Click the file on your PC to activate Setup program.
4. Assign IP address to WebEye with Setup program.
l Activate Setup program and assign a new IP address to WebEye.
l Change IP address from default one to a new one available on your local
network. Connected on a same local network, any IP address of WebEye
appears on Setup window even if the IP address is from remote network range.
l A user on the local network may access WebEye, when WebEye is assigned a
proper IP address of the local network, though if gateway address, broadcast
address and network mask are not assigned properly. However remote user
cannot access the WebEye without assigning its gateway address, broadcast
address and network mask properly.
l Even when you connected directly WebEye to a PC, you cannot access
WebEye if you don’t assign WebEye with local IP address
IP address is an identification code for computers and devices on a TCP/IP network. Networks using
TCP/IP protocol route messages based on the IP address of the destination. Within a closed network, IP
dom as long as each one is unique. However, connecting a private
IP address can be
hardware identification code that uniquely identifies each node of a network. The
MAC layer interfaces directly with the network media. Consequently, each type of network media
A unique MAC
. Select the default IP address of
lick on
licking the button,
1
WebEye (211.53.133.91).
5. After changing IP address, the
new IP address appears. C
the IP address.
4. Click this button to change IP
address. Upon c
a new window appears where you
change IP address.
IP Address
The selected IP address
2. & 6.
appears (211.53.133.91).
7. Click ‘Start Configuration’ button, to
access WebEye through Internet and
configure administration conditions.
* IP Address and MAC Address *
3. Enter Admin ’s
password. Default
password is ‘admin’.
addresses can be assigned at ran
network to the Internet requires using registered IP addresses to avoid duplicates.
acquired from a network administrator or an Internet service provider.
MAC Address (Media Access Control Address)
MAC address is a
requires a different MAC layer. The MAC address of WebEye is a 12-digit number.
address can be found on the label at the bottom of each WebEye.
l Please note!!
When an IP address is assigned to the WebEye, be careful not to assign the
WebEye with an IP address that is not compatible with the local network or
that is already in use by another computer or similar device. Please refer
below example and assign an IP address to WebEye.
Gateway address 192.168.1.1
Subnet mask 255.255.255.0
Broadcast address 192.168.1.255
Already used IP address 192.168.1.2 ~ 192.168.1.50
Available IP address for WebEye 192.168.1.51~ 192.168.1.254
However, if there is a subnet mask of 255.255.255.128, then IP addresses
from 192.168.1.129 to 192.168.1.255 are not in the same local network as the
IP address of 192.168.1.1 to 192.168.1.128.
5. Configure administrator’s condition.
l By clicking ‘ Start Configuration’ button on setup program, you may access
WebEye administration page through Internet.
5.1 Select ‘Network Configuration’ in the menu and configure.
WebEye set broadcast
automatically. It is possible to input
. Click ‘Ethernet’
button.
. Check if IP address
is same as assigned at
Setup program.
. Set gateway address. If an
assigned,
a popup message informs to
the built
clicking
s can be
viewed from the built in
1
3. Set Netmask.
5
unavailable address is
assign the address properly.
5.2 Select ‘Video Configuration’ in the menu.
2. Skip this step for
in CCD. However by
‘B/W’, B/W image
CCD.
2
.This button makes
4
address
diretly.
6. Click ‘Apply’ button.
. Select ‘Enable’ to use video
1
channel.
3. Choose proper
type between
NTSC and PAL.
5. Click ‘ Apply’ button.
6. Access WebEye image viewer and configure watching condition
address bar
of the Web browser (e.g. http://211.53.133.113) and
press ‘Enter ’ key.
me and
do
viewer.
This step is for Netscape
Navigator users only. Internet
1. Enter IP address of your WebEye in the
6.1 Enter IP address and access WebEye image viewer
6. Click ‘ Login’ button
to access real-time image
2. Click ‘WebEye Plug- in’ menu, for
Netscape Navigator users .
*
5. Check user na
password. Default values
not require retyping.
Explorer users can skip this step.
Download WebEye
This step is for Netscape
Navigator users only.
Internet Explorer users can
X into
time
* This step is for
.
users can
disregard this step.
*
skip this step.
3. Click ‘
Plug -in Now!’ button.
4. Click ‘Grant’ button. ‘Install
Successfully Completed’ will
appear.
Explorer users only
Netscape
7. Click ‘ Yes’ button to download and install Activeyour PC. After download of Active- X plug-in, real-
images can be seen.
Manual
article. Then download
installation program and install it following
WebEye
l If you experience a case that Active-X for Internet Explorer or Plug-in for
Netscape Navigator is not installed into your PC properly, please visit
‘ Download’ page in WebGate Internet homepage (http://www.webgateinc.com). And
download a program to install Active-X or Plug- in manually.
1. Click ‘Download’ menu
2. Click ‘
Series’ at ‘Download’
menu.
3. Click ‘WebEye Plugin/ActiveX –
Installation’
the description.
7. Manage the real-time image viewer.
d
. The below
external
etailed
imple viewer,
java applet viewer
in this
menu. For more information, please refer to
User’s guide.
image
size, and transmission
can be
altered in the scroll
o view
connect external cameras and
configure settings properly. For more
Set the desired viewer option. S
server-push viewer, and
viewer configurations are available
Images can be viewed in this section. T
other channels,
information, please refer to User ’s guide.
The Reference Guide has so far covered installation an
usage of the internal camera of WebEye
sections cover basic information on usage of
channels and viewing through firewalls. For d
information , please refer to the WebEye User’s Guide.
R esolution,
frame rate
bars.
II. Connecting external camera.
o connect
proper positions. Default positions of all 2
switches are up.
Video signal flows
through LAN Cable.
PC
Video signal flows
1. Functions of DIP switch.
To designate video signal termination. T
external CCTV cameras, place the switches in
2. Connecting external camera to WebEye
2.1 Connection diagram.
Dome Camera
through BNC Cable.
2.2 Connecting external camera to WebEye
to use the
or
according to
and CCTV monitor to
l Enter WebEye administrator ’s page
l Enter ‘ Video Configuration’ page and configure.
2. Choose ‘Color’
‘B/W’
external camera type.
3. Choose either NTSC or PAL
according to external camera type.
l
Connect an external camera and check DIP switches’ position
1. Select ‘Enable’
channel.
4. Click ‘Apply’ button.
Connect Dome camera to ‘Video Input’
‘Video Output’, DIP switches are up.
1.4. Connecting CCTV monitor or PC to WebEye
Video signal flows
through LAN Cable.
PC
Video signal flows
1.4.1 Connection diagram
DOME Camera
through BNC Cable.
l To monitor real-time image viewer through CCTV
monitor or PC, connect Dome camera to ‘ Video Input’
and CCTV monitor to ‘Video Output’. And DIP
switch(mark 1) is down ‘OFF ’.
l If CCTV monitor with DIP switches and it is possible
termination selection, it can shift that CCTV monitor to
termination of WebEye are ‘ON’ DIP switch of WebEye and
‘OFF’ DIP switch of CCTV monitor.
III. Connecting WebEye through firewall.
, key in
port (80) is blocked, change
Web server TCP port to any other port that
is open and is not occupied already on the
If default port (8080) is blocked, change Video server TCP port to
any other port that is open and is not occupied already on the
1. WebEye is blocked with firewall.
l If there is a firewall in the network where WebEye is connected, enter WebEye
administrator’s page and change TCP ports.
3. Click ‘Apply’ button.
l Access WebEye t hrough Internet browser.
2.
network.
1. If default
network.
4. If you have set IP address as ‘192.168.1.51’
and changed Web server TCP port as ‘81’
‘http://192.168.1.51:81’. Then press ‘Enter ’ key.
This image is transmitted through
Web server port on your network.
To monitor more efficiently, refer to
WebEye User ’s Guide.
2. User’s PC is blocked with firewall.
l If there is a firewall on the network where your PC is connected, enter WebEye login
page with IP address (ex: http://192.168.1.51).
l Enter ID and password.
l Click ‘behind firewal l’.
l Click ‘ Login’ button to enter server -push viewer.
l Or click ‘Server-push’ mode at default viewer, enter server-push viewer.
l Then enjoy real-time image that is transmitted through Web server port on
your Network.
For more detailed information on how to install PTZ
mechanism, auto iris lens, external sensor and relay, please visit
page in WebGate Internet homepage and
‘Download’
download related information.
http://www.webgateinc.com
Loading...