WebGate EH1600L, EH800M, EH400H, LH1600C, LH800L User Manual

Download

EH1600L, EH800M, EH400H, LH1600C, LH800L

Digital Video Recorder

Installation/User Manual

We sincerely appreciate purchasing Digital Video Recorder.

For product connection and initial configuration, please, refer to the

installation guide and for the product details, refer to user guide

English

Install&User Manual

Introduction

Thank you for purchasing a Webgate digital video recorder.

This manual is for LH1600C, LH800L, EH1600L, EH800M, EH400H. Before product installation

and operation, please become thoroughly familiar with this user manual and other manuals

referenced by this manual.

This user manual and the software and hardware described here are protected by copyright law.

With the exception of copying for general use within fair use, copying and reprinting the user

manual, either partially or in entirety, or translating it into another language without the consent

of Webgate Inc. is strictly prohibited.

This specification may change without prior notice for improvement of product performance.

Product Warranty and Limits of Responsibility

The manufacturer does not assume any responsibility concerning the sale of this product and

does not delegate any right to any third party to take any responsibility on its behalf. The

product warranty does not cover cases of accidents, negligence, alteration, misuse or abuse.

No warranty is offered for any attachments or parts not supplied by the manufacturer.

 Malfunctions due to negligence by the user

 Deliberate disassembly and replacement by the user

 Connection of a power source other than a properly rated power source

 Malfunctions caused by natural disasters (fire, flood, tidal wave, etc.)

 Replacement of expendable parts (HDD, FAN, etc.)

※ The warranty period for the HDD and Fan is one year after purchase.

This product is not for exclusive use of crime prevention but for assistance in cases as

fire or theft. We take no responsibility for damage from any incident.

Install&User Manual

Caution

As this equipment undergone EMC registration and suitable for business purpose, distributors

and users are aware of this point.

FCC Compliance Statement

Caution : Any changes or modifications in construction of this device which are not expressly

approved the party responsible for compliance could void the user's authority to operate the

equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications, Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

Warning

This is a class A product. In a domestic environment this product may cause radio interference

in which case the user may be required to take adequate measures

Warning

1. Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries

According to the Instructions

2. In case of changing built-in lithum battery, it should be replaced as same or kindred one to

prevent a danger of explosion. Since old batteries could be a factor of environment

contamination, be cautios to treat them.

3. Do not throw the batteries to fire or heating. Neither short circuiut or disassembly is

prohibited.

4. Do not charge the batteries provided with Remote Controller

Install&User Manual

Important Notice

1. Do not place heavy objects on the top of the product.

2. This equipment is indoor use and all the communication wiring are limited to inside of the

building

3. Product is for indoor use. It is not weatherproof. Use product with referring to its

environmental specifications (Temperature & Humidity). To clean the product, gently wipe the

outside with a clean dry cloth.

4. Product uses AC power of 110V ~ 240V. Be cautious not to cause electric damages to

product.

5. Be careful not to drop the product. Physical shocks may harm the product including internal

HDD. In addition, be sure the product is secured after installation.

6. Product is made of metal. Therefore you can hurt human beings if you throw it to them or hit

on them. When installing product, be cautious to locate on safe places where children are

unreachable.

7. If Product does not operate properly, please contact the closest WEBGATE distributor for

after sales service. Tampering or disassembling the product will void the warranty.

8. Security surveillance laws may differ for each country. Therefore, please contact the local

region first to avoid any surveillance law violations.

9. "Rack Mount Instructions - The following or similar

rack-mount instructions are included with the installation instructions:

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater than room ambient.

Install&User Manual

Therefore, consideration should be given to installing the equipment in an environment

compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount

of air flow required for safe operation of the equipment is not compromised.

C) Mechanical Loading - Mounting of the equipment in the rack should be such that a

hazardous condition is not achieved due to uneven mechanical loading.

D) Circuit Overloading - Consideration should be given to the connection of the equipment to

the supply circuit and the effect that overloading of the circuits might have on overcurrent

protection and supply wiring. Appropriate consideration of equipment nameplate ratings

should be used when addressing this concern.

E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.

Particular attention should be given to supply connections other than direct connections to

the branch circuit (e.g. use of power strips)."

Experience and technical skills are needed for the installation of this product as an improper

installation may cause fire, electric shocks, or defects. Any installation job should be performed

by the vendor you purchased this product from.

The content of this manual can differ according to firmware or Software upgrading, and the

standard and appearance of products may be changed for the improvement of quality without

an advance notice.

Install&User Manual

Contents

INTRODUCTION ............................................................................... 1

KEY FEATURES .............................................................................. 10

INSTALL MANUAL.......................................................................... 13

1. FEATURE .................................................................................... 13

1.1 Supplied Accessories .................................................................................................... 13

1.1.1. EH Series .............................................................................................................. 13

1.1.2. LH Series .............................................................................................................. 14

1.2. Description & Function .................................................................................................. 15

1.2.1. Front ...................................................................................................................... 15

1.2.2. Rear ...................................................................................................................... 19

1.2.3. REMOTE CONTROLLER ...................................................................................... 21

2. INSTALLATION ........................................................................ ２３

2.1 Installation and Connection ........................................................................................ ２３

2.1.1 Connecting & Running ........................................................................................ ２３

2.2 Running OSD menu................................................................................................... ２５

2.2.1 OSD menu configuration ..................................................................................... ２５

2.2.2 Setting remote controller ..................................................................................... ２６

2.2.3 Install examples .................................................................................................. ２７

2.2.4 Basic Setting ...................................................................................................... ２９

2.3 Connecting and configuring DIO ports........................................................................ ３３

2.3.4 HDD ................................................................................................................... ４４

2.3.5 Remote monitor and control ................................................................................ ４５

USER MANUAL ........................................................................... ４７

Install&User Manual

3 MENU USE .............................................................................. ４７

3.1 Menu Structure .......................................................................................................... ４７

3.2 Function Menu ........................................................................................................... ４７

3.3 Factory Reset ............................................................................................................ ４８

4 MONITORING .......................................................................... ５４

4.1 Basic Screen ............................................................................................................. ５４

4.2 Single Fll Screen Mode .............................................................................................. ５４

4.3 Multi Screen Mode ..................................................................................................... ５４

4.4 Screen Description .................................................................................................... ５５

4.5 Auto Switch Mode ...................................................................................................... ５５

4.5.1 System Standard Mode ...................................................................................... ５５

4.5.2 User Sequence Mode ......................................................................................... ５６

4.6 Event Screen ............................................................................................................. ５７

4.7 Zoom Screen Mode ................................................................................................... ５８

4.8 Pause Live Screen .................................................................................................... ５８

4.9 PTZ Control ............................................................................................................... ５９

4.9.1 Pan/Tilt .................................................................................................................... ６０

4.9.2 Zoom/Focus............................................................................................................. ６０

4.9.3 Load Preset ............................................................................................................. ６０

4.9.4 Save Preset ............................................................................................................. ６０

4.9.5 Auxiliary On ............................................................................................................. ６０

4.9.6 Auxiliary Off ............................................................................................................. ６１

4.9.7 Menu ....................................................................................................................... ６１

5 PLAYBACK ............................................................................. ６２

Install&User Manual

5.1 Playback Mode .......................................................................................................... ６２

5.1.1 Playback on Standard monitor (16 / 9 / 4 division) ............................................... ６２

5.1.2 Playback function ............................................................................................... ６２

5.2 SEARCH MODE ........................................................................................................ ６３

5.2.1 Time Search ....................................................................................................... ６３

5.2.2 Schedule Search ................................................................................................ ６３

5.2.3 Event Search ...................................................................................................... ６４

5.2.4 Thumbnail Search............................................................................................... ６５

5.3 Copy.......................................................................................................................... ６６

5.3.1 CD/DVD ............................................................................................................. ６６

5.3.2 RE4 .................................................................................................................... ６７

5.3.3 AVI ..................................................................................................................... ６８

6. CONFIGURATION .................................................................... ６９

6.1 Recording Structure ................................................................................................... ６９

6.2 System Setup ............................................................................................................ ６９

6.2.1 Date/Time ........................................................................................................... ６９

6.2.2 Disk .................................................................................................................... ７２

6.2.3 User Setup ......................................................................................................... ７４

6.2.4 Utility .................................................................................................................. ７６

6.3 Network ..................................................................................................................... ７８

6.3.1 xDSL .................................................................................................................. ８０

6.3.2 WRS ................................................................................................................... ８０

6.4 Device Setup ............................................................................................................. ８１

6.4.1 Camera Setup .................................................................................................... ８２

6.4.2 Monitor Setup ..................................................................................................... ８３

6.4.3 Audio Setup ........................................................................................................ ８４

6.4.4 Text Setup .......................................................................................................... ８５

6.4.5 Serial Setup ........................................................................................................ ８６

6.5 Event Setup ............................................................................................................... ８７

6.5.1 Event Check ....................................................................................................... ８８

Install&User Manual

6.5.2 Sync Event ......................................................................................................... ８９

6.5.3 Motion Detection ................................................................................................. ９１

6.5.4 Sensor ................................................................................................................ ９２

6.5.5 Preset ................................................................................................................. ９２

6.6 Recording setup ........................................................................................................ ９４

6.6.1 Program setup .................................................................................................... ９４

6.6.2 Manual/Schedule recording setup ....................................................................... ９６

7. WEB VIEWER ....................................................................１００

7.1 System requriement............................................................................................... １００

7.2 Login ..................................................................................................................... １００

7.3 User Setup ............................................................................................................ １０１

7.4 Browser available .................................................................................................. １０１

7.5 Monitor .................................................................................................................. １０２

7.5.1 Screen division and changing video position ................................................... １０２

7.5.2 Move to Playback ........................................................................................... １０３

7.5.3 Channel On/Off ............................................................................................... １０４

7.5.4 Sensor Indication ............................................................................................ １０４

7.5.5 Relay opeartion .............................................................................................. １０４

7.5.6 Using microphone ........................................................................................... １０４

7.5.7 Event data ...................................................................................................... １０５

1.2.1. Video Recording & Save saving ...................................................................... １０５

7.5.8 UsingPTZ ....................................................................................................... １０６

7.5.9 Using Audio .................................................................................................... １０７

7.5.10 Closing Video Channel ................................................................................... １０７

7.6 Playback................................................................................................................ １０８

1.2.2. Video Division & Changing Channel ................................................................ １０８

7.6.1 Image recording .............................................................................................. １０８

7.6.2 Printing ........................................................................................................... １０９

7.6.3 Backup ........................................................................................................... １０９

7.6.4 Web Monitor ................................................................................................... １１０

Install&User Manual

7.6.5 Channel On/Off ............................................................................................... １１０

7.6.6 Saving time & Checking Rec. Capacity ........................................................... １１０

7.6.7 Searching Calander ............................................................................................. １１０

7.6.8. Functional function at the buttom of monitor .................................................... １１１

8. USER MANUAL FOR MOBILE VIEWER .........................１１２

8.1 Log-In page ........................................................................................................... １１２

8.2 Monitoring page ..................................................................................................... １１２

TROUBLE SHOOTING .............................................................１１４

AVAILABLE HDD ......................................................................１１６

COMPATITABLE CD/DVD LIST ...............................................１１７

SPECIFICATION........................................................................１１７

EH1600L, EH800M, EH400H ........................................................................................... １１７

LH1600C, EH800L ........................................................................................................... １１９

PRODUCT SIZE ........................................................................１２３

Install&User Manual

KEY FEATURES

Monitoring Screen

Supprots real live video with high resolution per each channel and variable display mode.

 Real H.264 Video

 Varianble display mode

EH1600L : 1/4/9/10/16 channel mode

EH800M : 1/4/9 channel mode

EH400H : 1/4 channel mode

LH1600C : 1/4/9/10/16 channel mode

LH800L : 1/4/9 channel mode

 Auto Switching

EH1600L : Composite x 2, DVI x 1

EH800M : Composite x 2, DVI x 1

EH400H : Composite x 2, DVI x 1

LH1600C : Composite x 2, VGA x 1

LH800L : Composite x 2, VGA x 1

Audio Recording

Supprots real-time audio input and recording

 Simultaneous 4ch audio input & recording available

 Input : 4Ch, Output : 1ch (Rear)

 Simultaneous audio recording and playback available

Install&User Manual

Recording

It supports max. 480ips/EH1600L, 240ips/EH800M, LH1600C, LH800L, 120ips/EH400H

recording at High-Resolution (H.264) and available to record max. 5

seconds before triggering an event. Also, convert function is available protecing privacy.

 H.264 Video recording with High-Quality

EH1600L : CIF(360x240) 480ips

EH800M : 2CIF(704x240) 240ips

EH400H : D1 (704x480) 120ips

LH1600C : CIF(360x240) 240ips

LH800L : CIF(360x240) 240ips

 Supprots manual & schedule recording

 Video loss detection

 Supprots archiving event list(Sensor, Video Loss, Motion detection, Text)

 Available record Max 5 seconds before triggering an event per each channel

Search/ Playback

It supports variable and convenient functions for search & playback

 Play back by time, date, Channel

 Easy and convenient search using mouse

 Pre/post search from a freeze frame

 Play back by Event (Sensor, Video Loss, Motion Detection, Text

 Easy & convenient search using Remote Controller & Jog/Shuttle

(except LH1600C, LH800L)

Back up device

It is available to backup to DVD-R, CD-R, USB memory by user’s choice.

(LH1600C, LH800L is available as an option.)

Install&User Manual

 Supprots various back up device : DVD-R, CD-R, USB memory

 Extention HDD Storage (External extention Storage device)

Network

It supports variable network like LAN, XDSL and easily control from remote site using PC

cliet viewer.

 E-mail notification thru. TCP/IP, DHCP in case of triggering an event

 Live monitoring form remote site (Whole screen or available to select quad

screen

 Available to playback, recording, search and DVR management thru.

network viewer in PC

 Available to record, search & playback by time from remote site.

 Supprots 10/100Mbps Ethernet/xDSL

 Multiple DVR connection

Etc.

 Supports User friendly GUI and mouse function

 Easy and simple firmware upgrade thru. USB memory

 Recorded data back up thru. USB port

 PTZ Control (SPEED DOME), PRESET fucntion

 Available to control up to 16 DVRs with one remote controller

Install&User Manual

Install Manual

1. Feature

1.1 Supplied Accessories

Unpack and check all the items as below

1.1.1. EH Series

AC Cord, Remocon, Setup CD, DVI Converter, SATA Cable, HDD Fixing Screw, Quick Guide

Install&User Manual

1.1.2. LH Series

AC Cord, Remocon, Setup CD, SATA Cable, HDD Fixing Screw, Quick Guide

Install&User Manual

1.2. Description & Function

1.2.1. Front

1.2.1.1. EH-Series Front

Item Description

DVD-Multi (For

Back up)

Back up use for recorded data by DVD/CD media

2 Channel Button To select video input channel

REC LED Displays recording status

COPY LED Displays copy status

HDD LED Displays HDD running.

NETWORK LED Displays network connection

EVENT LED Displays event detection

4 Power Turn on/ off power

5 USB port Use connecting USB memory or Mouse

6 REC To start or stop manual recording

7 Multi To change DVISION in live or playback mode

8 SEQ To run or stop user sequence

9 Copy To enter copy mode

10 Search To enter search mode

11 PTZ To start PTZ function or stop

12 Func To enter function mode

13 Relay Manual On/Off button for relay

Install&User Manual

14 Mon To change Monitor/ Stop

15 Menu To enter menu

16 ESC To escape from menu or close pop-up window

Enter/Play To enter playback mode or select menu

18 ◀/REW To move or select in menu and change replay speed to

reverse direction in playback mode

19 ▶/FWD To move or select in menu and change replay speed to

forward direction in playback mode

20 ▲/Pause To move or select in menu and pause live/ replay video

21 ▼/Stop To stop replay in playback mode

Jog/ Shuttle

STEP function control, Playback direction change,

Playback speed control

Install&User Manual

1.2.1.2. LH-Series Front

Item Description

DVD-Multi (For

Back up)

Back up use for recorded data by DVD/CD media

2 Channel Button To select video input channel

REC LED Displays recording status

COPY LED Displays copy status

HDD LED Displays HDD running.

NETWORK LED Displays network connection

EVENT LED Displays event detection

4 Power Turn on/ off power

5 USB port Use connecting USB memory or Mouse

6 REC To start or stop manual recording

7 Multi To change DVISION in live or playback mode

8 SEQ To run or stop user sequence

9 Copy To enter copy mode

10 Search To enter search mode

11 PTZ To start PTZ function or stop

12 Func To enter function mode

13 Relay Manual On/Off button for relay

14 Mon To change Monitor/ Stop

15 Menu To enter menu

16 ESC To escape from menu or close pop-up window

Enter/Play To enter playback mode or select menu

Install&User Manual

18 ◀/REW To move or select in menu and change replay speed to

reverse direction in playback mode

19 ▶/FWD To move or select in menu and change replay speed to

forward direction in playback mode

20 ▲/Pause To move or select in menu and pause live/ replay video

21 ▼/Stop To stop replay in playback mode

Install&User Manual

1.2.2. Rear

1.2.2.1. EH-Series REAR

번호

Input/ Output name Descrtiption

1 Ground Ground between DVR & external device

2 CH1~16 BNC input for camera connection

EH1600L : 16EA, EH800M : 8EA, EH400H : 4EA

3 Loop out BNC output(Loop) for camera connection

4 Monitor/ Spot BNC connection for monitor output

5 Audio Input(RCA) RCA connection for Audio input

6 Audio Output Speaker output terminal

7 Ethernet For network connection (RJ-45)

8 eSATA eSATA external storage connection

9 DVI OUTPUT Output for DVI monitor connection

10 RS-232C D-Sub Text equipment, Keyboard connection

11 Termination Ohm Termination Ohm for Com2, Com3

12 Relay/Serial Connection for Relay and Serial(RS-485)

13 Sensor IN Input for external sensor

14 FAN Cooling system against over heating

15 Power connector Socket for AC100V~AC240V power cord

Install&User Manual

1.2.2.2. LH-Series REAR

번호

Input/ Output name Descrtiption

1 Ground Ground between DVR & external device

2 Power connector Socket for AC100V~AC240V power cord

3 CH1~16 BNC input for camera connection

LH1600C : 16EA, LH800L : 8EA

4 Monitor/ Spot BNC connection for monitor output

5 Audio Input(RCA) RCA connection for Audio input

6 Audio Output Speaker output terminal

7 Ethernet For network connection (RJ-45)

8 RS-232C D-Sub Text equipment, Keyboard connection

9 VGA OUTPUT Output for VGA monitor connection

10 Termination Ohm Termination Ohm for Com2, Com3

11 Relay/Serial Connection for Relay and Serial(RS-485)

12 Sensor IN Input for external sensor

Install&User Manual

1.2.3. REMOTE CONTROLLER

It is available to use all functions of DVR. If several DVR are set with unique ID numbers,

they can be controlled with one remote controller. To use remote controller, it is necessary

to set ID first which want use. Keep pressing ID button repetedely (Up to Max. 16 times)

and use it matching DVR & ID.

No. Iten Description

1 ID To select Remote Controller ID

2 LOCK Not use

3 COPY To indicate copy menu, copy recorded data to USB

4 BACKUP Not use

5 RELAY ON To manually ON

6 RELAY OFF To manually OFF

7 SEQ Auto sequencing

8 MULTI To change division

9 ZOOM To run digital zoom

Install&User Manual

10 SEARCH To indicate search menu

11 CHANNEL BUTTON To select channel

12 SELECT Not use

13 +10 In case of selecting over 10

(+10 + 1)

14 FN1 Not use

15 FN2 Not use

16 MENU Covert to menu screen

17 HELP Not use

18 ◀/REW Move setting menu to left direction/REW

19 ▶/FWD Move setting menu to right direction/FWD

20 ▲/PAUSE Move setting menu to top direction/PAUSE

21 ▼ Move setting menu to bottom direction/STOP

22 ENTER/PLAY Menu selection/Playback

23 ENTER To select menu

24 EXIT To cancel setting, escape from menu

25 FAST REWIND(◀◀) Speedy replay to reverse direction

26 REWIND PLAY(◀) Replay to reverse direction

27 FORWARD PLAY(▶) Repleay to forward direction

28 FAST FORWARD (▶

▶)

Speedy replay to forward direction

29 STOP( ) To stop replay

30 STEP REVERSE(◀l) Replay to reverse direction by each frame

31 STEP FORWARD (l▶) Replay to forward direction by each frame

32 PAUSE(ll) To freeze playback

33 P/T PAN/TILT Control

34 LOAD PRESET To read preset

35 AUX ON Auxiliary ON

Install&User Manual

２３

2. Installation

2.1 Installation and Connection

2.1.1 Connecting & Running

2.1.1.1 Connecting camera

Connect CCTV camera to DVR with BNC cable as below

[EH-Series] [LH-Series]

- The video type for all channels should be either NTSC or PAL, not be combined both

- DVR sets video signal’s impedance (75Ω) automatically. Impedence is set as 75 Ω basically. If

connecting a dvice to video output, impedance will be “Hi-z” status.

- Video Type (NTSC/PAL) should be changed after booting DVR. The order of camera

recognition follows ch1 through Ch16 camera amd 1st recognized camera type leads other

camera type.

2.1.1.2 Connecting monitor

Connect CCTV monitor to DVR with BNC cable as below.

Will be able to connect BNC, DVI and VGA.

[EH-Series] [LH-Series]

2.1.1.3 Connecting Audio

Connect audio signal to DVR with using RCA cable or D-SUB as below;

Install&User Manual

２４

[EH-Series] [LH-Series]

2.1.1.4 Supplying Power

Connect power cable as below;

[EH-Series] [LH-Series]

- When supplying power, DVR starts booting automatically.

- In order to cut off power, press power switch on DVR front during 5 seconds, then select

“YES” after appearing a pop-up window.

- For supplying power again, push the Power button.

[EH-Series] [LH-Series]

Install&User Manual

２５

2.2 Running OSD menu

2.2.1 OSD menu configuration

Press [MENU] in keypad of front to open configuration menu as below;

(1) Main Menu : The selected tab is show in bright color and the related sub-menu will be

shown left- below the tab. To move to the previous/next tab, use the [◀/▶] arrow buttons. To

move to a sub-menu press the [Enter] key.

(2) Sub-menu : The selected sub-menu is shown as tab title and the related setting will be

shown. To move to the previous/next tab, use the [◀/▶▲/▼] arrow buttons. To move to the

related setting press [Enter]. To move to upper main menu, press [ESC] button.

(3) Setting page : The selected tab is shown as orange, To move to the previous/next tab, use

the [◀/▶] or [▲/▼] arrow button and press [Enter] key for value setting. Whn setting value is a

word, a dialogue box to edit the word will be open. When setting value is number, it should be

set with using [◀/▶] or [▲/▼]. Press [ESC] button when the value is set and also [ESC] button

is available to upper sub-menu.

2.2.1.1 Dialogue box to edit a word

Dialogue box to edit a word is image shown as below; It is available to input both word and

bumber.

Install&User Manual

２６

Keep pressing [▲/▼], [◀/▶] arrow button until the word is looking for and press Enter. In case

of deleting input word press [], spacing words press [] button. To exit from dialogue box,

press [Enter] after finishing word input.

2.2.2 Setting remote controller

2.2.2.1 Setting ID of DVR

When controlling several DVRs with one remote controller, set Remote Control ID as follws;

(1) Press the [MENU] button

(2) [▶] Select “system” with using [▶] arrow button and press [Enter] or [▼] button

(3) [▼] Select “Utility” with using [▶] arrow button and press [Enter] button.

(4) Select “Remote Control ID” and press [Enter]

(5) [◀/▶] Select a value using [◀/▶] arrow buttons and press [ESC]

(6) Press the [ESC] button to return to the monitor mode.

Up to 16DVRs can be controlled with a single remote controller.

When not using remote controller, set the Remote Control ID as “Off”

2.2.2.2 Selecting ID

If several DVRs are with unique ID numbers, they can be controllerd with one remote controller.

To select a specific DVR, keep pressing the ID button of remote controller until a buzzer sounds

during 2 seconds.

Install&User Manual

２７

2.2.2.3 Operaable range of remote controller

2.2.2.4 Loading the batteris into the remote controller

Remote controller required two AAA-type batteries. Please, refer the following installation step.

1. Remove the battery cover

2.Taking care the the poles

(+/-) are correctly

positioned.

3. Replace the battery cover

2.2.3 Install examples

2.2.3.1 Basic configuration

[EH-Series]

Install&User Manual

２８

[LH-Series]

2.2.3.2 Advance configuration

[EH-Series]

[LH-Series]

2.2.3.3 External storage & Back up configuration

Install&User Manual

２９

[EH-Series] [LH-Series]

2.2.3.4 Internet/ Intranet configuration

[EH-Series]

[LH-Series]

2.2.4 Basic Setting

Install&User Manual

３０

2.2.4.1 Viewing Image

When power is on, eDVR starts automatically and displayed in basic 16ch-split screen after

booting.

If user password is set, a prompt for entering the password will be appeared. Factory

default is reserved as not responding keypad on DVR front (It is not from factory default).

2.2.4.2 Setting Date & Time

- Press [MENU] button and select “ System” when OSD menu is appeared.

- Select“Date/Time”and press [Enter] button.

Time Zome

(1) Select “Time Zone” using [◀/▶] or [▲/▼] arrow button and press [Enter] button.

(2) [◀/▶] Select “Time Zone” using [◀/▶] arrow button and press [ESC] button.

Daylight saving

(1) Summer Time is only activated for Time Zine that uses Daylight savings.

(2) Select “Daylight Saving”using [◀/▶] or [▲/▼] arrow button and press [Enter] button.

Install&User Manual

３１

(3) Select On/Off using [◀/▶] arrow button and press [ESC] button.

NTP

(1)Select NTP Function

(2)Select “Client or Server or Both” using [◀/▶] or [▲/▼] arrow button and press [Enter] button.

(3)Select “Public or Both” using [◀/▶] arrow button and press [ESC] button

on ‘Client or Both’mode.

(4) Enter ‘Server IP address’ when you set the next server as Local.

(5) Set Server and Communicate cycle with Interval.

Date Format

(1) Select “Date Format” using [◀/▶] or [▲/▼] arrow button and press [Enter] button. Select a

value using [◀/▶] arrow button from YYYY/MM/DD, MM/DD/YYYY, DD/MM/YYYY.

(2) Press [ESC] after finshing value setting.

Time

(1) Select “Time” using [◀/▶] or [▲/▼] arrow button and press [Enter] button.

(2) Select Date, Time using [◀/▶] arrow button and set value using [▲/▼] arrow button.

(3) Press [ESC] after finshing value setting.

Apply

Most setting values are appled automatically, when exiting form the related menu page. But

“Date” & “Time” setting are not applied automatically because they may critically affect the file

system of the recorded HDD. To apply Date/ Time settings confirm with [Apply Date/Time]

buttons.

(1) Select “Apply Date/ Time” using [◀/▶] or [▲/▼] arrow button and press [Enter]. Then, a

warning message will be appeared as below image;

(2) Select using [◀/▶] or [▲/▼] arrow button and select “YES”, then, press [ENTER] button.

To cancel, press [ESC] button.

Install&User Manual

３２

2.2.4.3 Record Setting

Select “Record” pressing menu button in front.

Program Setting

Set resolution, frame rate, quality by each channel that user want record in “Program” of record

menu.

Schedule Setting

Install&User Manual

３３

Set recording mode as “Scheduel & Event” and set by date/ time.

Checking method for recording

If recodrding setting is finished correctly, “REC LED” in front is flickering. In addition, it

is marked [S] indicating that all channels are recroding.

2.3 Connecting and configuring DIO ports

2.3.1 Wire Handling

When connecting a wire to a terminal block, follow the instruction below. Not the different types

of wire that can be used.

- Standard wire : Pie off the wiring cover 8~10mm and solder it. Wire gage should

AWG 22~26.

- Sold wire : Peel off the wiring cover 8~10mm and solder it.Wire gage should be AWG 20~26

2.3.2 Inserting & removing wire

To insert & remove wire in Terminal Block, use a screwdriver in the diagram to the below;

Install&User Manual

３４

2.3.3 Connecting and configuring sensor

2.3.3.1 Specification

In order to run sensor input DVR normally, the following conditions are required.

Spec

Input Ch Transistor input

EH1600L. LH1600C : 16EA,

EH800M, LH800L : 8EA

EH400H : 4EA

Input type N.C, N.O supprt

Supported sensor Dry contact sensor

Way of connecting Connecting the trimmed wire to terminal block

Performance

Available input

pulse range

Minimum 500ms

Output current Typical DC 12mA

Connecting sensor input

Connect S1 ~ S16(S8. S4) with referring the following image. It shows to connect a dry contact

(Please refer “Wire Handling”).

[EH Series] [LH Series]

Install&User Manual

３５

Setting Sensor

(1) Press [Menu] button and select “Event” when OSD menu is appeared.

(2) Move to sub menu pressing [Enter] or using [▼] button and select [Enter]

All sensor

It is used when setting for all sensors and set Off, or Normal Open (N.O.) / Normal Close

(N.C.) type.

(1) Select All and set type.

Each sensor

It is used when setting for each sensor and set selecting each sensor.

(1) Select sensor and press [Enter] button.

(2) Select sensor that user want set and set type

(3) Press [ESC] after finishing value setting.

Install&User Manual

３６

2.3.3.2 Connecting relat and setting

Specification

In order to run relay output of DVR normally, the following conditions are required.

SPEC

Output Ch. 2EA relay outputs

Output type Dry contact

Connecting type Connect the trimmed wire to terminal block

Perfromance

DC 30V 1A

AC 125V 0.5A

Connecting relay out

Connect R1 ~ R2 with referring to the following images, it shows to connect a warning light.

Please refer the “Wire Handling”.

[EH Series] [LH Series]

Relay setting

It is available to run relay selecting from sensor, motion detection, Video Loss which is normal

event source and Disk error, Disk full, authentication fail, WRS registration fail which is system

event source. Also, user can set working condition by schedule. In case of using control center

thru. network, realy could be run from remotely.

Install&User Manual

３７

2.3.3.3 Connecting serial port

Configuring serial ports for Pan/Tilt/Zoom

If DVR supports thru. COM port, it is available to connect PTZ camera and control it. For a list of

supported protocols, please refer to the list on the OSD configuration menu. The following figure

shows how to connect PTZ camera to RS485 (COM2/COM3). When using another serial port,

connect it with referring to each connection diagram below.

Please refer the “Wire Handling”.

[EH Series] [LH Series]

Serial communication port diagram

Install&User Manual

３８

COM1 Connection (RS-232)

COM2/COM3 Connection (RS-485)

Available PTZ is same as below table.

Model Name Manufacturer

Keyboard KBD300A, WGI SPD1800/2600

Webgate

WKC-100 Keyboard

Webgate

BOSCH AutoDome, TC8560X-4

Bosch

PELCO(P), PELCO(D)

Pelco

Sony EVI-D3x

Sony

VT VPT-4x

AD SpeedDome

SungJin SJ372R1’

Sungjin

Samsung SCC641

Samsung Electric

Panasonic WV-CS850

Panasonic

Install&User Manual

３９

SDZ160/330, Samsung SPD,

Keyboard SCC3000, Samsung SRX-100B

Samsung Techwin

LG GAC-PT2

Merit-Lilin FastDome

Merit

Elmo PTC200C

Elmo

Canon VC-C4

Canon

HTC-230S

Dongyang Unitech

Honeywell 755/655, HRX-2000, ScanDome2

Honeywell

RVision

RVT

Elbex

VIDO

VICON

Vicon

Hunt

ORX-1000

Sysmenia

Fine CRR-1600

LiveEye

Tokina

Kodicom KRE

Kodicom

Nuvico

Serial Setting

You can set up both serial port and PTZ from remote menu under network menu.

From serial setting, you can set protocol, port, baudrate, parity bit, stopbit and databit.

After completed serial setting, select desired channel from camera menu, and setting up PTZ

Home, PTZ Idle Time, PTZ Port, and PTZ address.

Install&User Manual

４０

2.3.3.4 Connection to external device via Seria port

Text input device connection (ATM / POS / Access Control)

Using COM1/RS232, TEXT DATA can be recorded with synchronizing POS/ATM.

Like above picture, connect COM1/RS232 (9pin D-Sub) in Device menu and configure Serial

and Text.

Serial (COM1) Setup

(1) Select “Device” in OSD menu and move to sub menu.

(2) Seleting COM1 and configure “Text”in Device

(3) Setup the value of Baud Rate/Parity/Stop bit/Data bit with the device.

Install&User Manual

４１

Text Set up

(1) Select “Deice” on OSD, and move to sub menu.

(2) Select “Text”and configure relevant text information

Since external device can not be recognized, before installing, please, ask to the shop.

2.3.3.5 USB Device Connection

USB port is for the simple video copy (within 1 hour) on USB Flash memory. Its recommended

specification is same as below.

USB Spec. Ver 2.0 Device USB Memory Stick, Voltage/electric current

Max. 200mA per DC 5V / Port

[EH Series] [LH Series]

Install&User Manual

４２

It should be formatted by FAT32.

In case of normal connection, if executing Copy menu, disk will be recognized same as

below and Set copy range  Select Drive  Execute Copy.

[CD/DVD Copy]

[RE4 Copy]

Select the channel to copoy

Install&User Manual

４３

[AVI Copy]

A USB Flash memory which should install additional program on Windows OS, can not

be recognized.

2.3.3.6 Video In/Out connection

Video Input/Output is Loop through and check the connectivity automatically and set end

resistance.

For instance, if connected by Video input, end resistance is configured by75Ω and if

Video in/output is same, it will be Hi-z mode. Therefore, in case that Input/Outut are connected

at the same time, end resistance of device receving output should be configured by 75Ω.

[EH Series]

Install&User Manual

４４

[LH Series]

2.3.3.7 Audio In/Out connection

There are 4 RCA Audio Input and 1 RCA output.

2.3.4 HDD

※ Please, refer to Appendix for available HDD list

2.3.4.1 HDD registration and format

After mounting HDD and booting system, “Disk Manager” will execute automatically.

If not, please, check the connectivity of HDD.

(1) Press [Enter] button in “Disk Manager”

(2) Using [▲/▼] Key, select new HDD(Displayed [No] on Enabled item) and press [Enter]

(3) If you see the message for format, select [Yes].

(4) Press [ESC] and escape from “Disk Manager”

Install&User Manual

４５

2.3.5 Remote monitor and control

Via Internet/Intranet, in remote site, user can access with PC.

2.3.5.1 Ethernet connection

[EH Series] [LH Series]

(1) Cut Power.

(2) Connet Ethernet cable to DVR and Hub.

(3) Input Power.

To protect DVR demage, after connecting Ethernet cable, input Power.

Please, check Ethernet cable connection firmly.

Input power on DVR and check their connectivity.

2.3.5.2 Network configuration

Install&User Manual

４６

Ethernet

Set type as Ethernet and input IP, Netmask,Gateway, DNS.

The way to input is using directional key or mouse wheel.

PPPoE

Set type xDSL, and move to xDSL menu.

First, change Ethernet Port

Please, input ID and Password for PPPoE.

WRS

After changing interval over 1 min, register WRS address and product and input Group ID.

Install&User Manual

４７

User Manual

3 Menu Use

3.1 Menu Structure

The menu structure will be shown like below image, and each menu setting method descriped

from chapter 4 to chapter 6.

3.2 Function Menu

To execute Function menu, click the right button of mouse or select ‘FUNC’ button on front

panel. The Function menu can be controlled by mouse.

Each function can be executed by clicking right button of mouse and click desired icon.

The Function menu also can be controlled by front part of DVR’s buttons.

Please refer to below picture for the Function menu structure.

Install&User Manual

４８

3.3 Factory Reset

In order to reset value to factory value, go to System Setting->System->Setting, and once press

Factory Reset then the warning message will be appear, click “Yes” to reset the DVR value to

factory.

Default Value from Factory

System

Date /

Time

Time Zone UTC 00:00 Dublin

Daylight Saving Off

NTP Function Korean

Sync With

NTP

Off

NTP Mode Client

NTP Server

Loc.

Public

NTP Local

Server IP

0.0.0.0

Interval 1(hour)

Install&User Manual

４９

Holiday Select UTC 00:00 Dublin

Date Format No

Time MM/DD/YYYY

Disk

Over Write(Auto

Deletion)

Block Playback Off

Disk Full Alarm

Warning

50oC

Disk Manager >>

Disk Status >>

User

Setup

No Password used

Utility

DVR Alias DVR0

DVR Keyboard ID 1

Remote Controller

All

Language English

Firmware Update >>

System Log >>

Factory Reset >>

Network

Type Ethernet

DHCP Off

IP addr Default IP

Net Mask Default Net Mask

Gateway Default Gateway

DNS1 0.0.0.0

Additional DNS >>

Port 80

Band Width

Limit(Mbps)

0.0

xDSL

User ID Guest

Password *****

Status xDSL not connected

WRS

Interval Off

URL www.webgateinc.com

Install&User Manual

５０

Group Newbie

Status Not Registerd

Device

Camera Camera Number Ch1

Name Cam 1

Status On

Type NTSC

Color Color

AGC Enable

Bright 0

Contrast 0

PTZ PTZ Home Off

PTZ Idle

Time

PTZ Port None

PTZ Address 0

Monitor

Alarm Pop-up(Sec) Off

User Sequence

Configuration

SEQ Time(Sec) 5

Covert >>

Multi Moce 4E, >>

VGA Mode 800x600@56Hz

Infor Level >>

Audio

Audio Channel

Audio Recording

Audio Gain

Sync Video Channel

Audio Mix

Text

Recording Off

Sync Test With Ch1

Device Manual

Seek Header Off

Header 1 Header1

Header 2 Header2

Install&User Manual

５１

Delimiter 0D0A

Timeout(ms) 1000

Lines 20

Serial

Serial Port Com1

Device Non

Interface RS232

Baud Rate 9600

Parity Bit None

Stop Bit 1

Data Bit 8

Event

Event Check Always

Event Action Relay1

Action Duration 10 Sec

Normal Event

Source

System Event

Source

Motion

MD All

Sensivity 2

Area Set All

Sensor Sensor All, N.O.

Preset

Channel Mumber Ch1

Preset Sensor1, Preset1

Record

Record Mode Manual & Event

Program ProgramK

Event Duration >>

Playback

Deinterlace

Program

Normal Resolution All D1

Frame Rate All 6

Quality All Q5

Event Resolution All D1

Frame Rate All 6

Quality All Q5

Install&User Manual

５２

Program initial value

LH800L

Record mode

Normal Event

Division Res Fps Q Res Fps Q

Program

A D1 7 Q5 D1 7 Q5

B D1 4 Q5 D1 4 Q5

C D1 2 Q5 D1 2 Q5

D Half 15 Q5 Half 15 Q5

E Half 7 Q5 Half 7 Q5

F Half 4 Q5 Half 4 Q5

G CIF 30 Q5 CIF 30 Q5

H CIF 15 Q5 CIF 15 Q5

I CIF 7 Q5 CIF 7 Q5

LH1600C

Record mode

Normal Event

Division Res Fps Q Res Fps Q

Program

A D1 4 Q5 D1 4 Q5

B D1 2 Q5 D1 2 Q5

C D1 1 Q5 D1 1 Q5

D Half 7 Q5 Half 7 Q5

E Half 4 Q5 Half 4 Q5

F Half 2 Q5 Half 2 Q5

G CIF 15 Q5 CIF 15 Q5

H CIF 7 Q5 CIF 7 Q5

I CIF 4 Q5 CIF 4 Q5

EH400H

Record mode

Normal Event

Division Res Fps Q Res Fps Q

Program

A D1 30 Q5 D1 30 Q5

B D1 15 Q5 D1 15 Q5

C D1 7 Q5 D1 7 Q5

D Half 30 Q5 Half 30 Q5

Install&User Manual

５３

E Half 15 Q5 Half 15 Q5

F Half 7 Q5 Half 7 Q5

G CIF 30 Q5 CIF 30 Q5

H CIF 15 Q5 CIF 15 Q5

I CIF 7 Q5 CIF 7 Q5

EH800M

Record mode

Normal Event

Division Res Fps Q Res Fps Q

Program

A D1 15 Q5 D1 15 Q5

B D1 7 Q5 D1 7 Q5

C D1 4 Q5 D1 4 Q5

D Half 30 Q5 Half 30 Q5

E Half 15 Q5 Half 15 Q5

F Half 7 Q5 Half 7 Q5

G CIF 30 Q5 CIF 30 Q5

H CIF 15 Q5 CIF 15 Q5

I CIF 7 Q5 CIF 7 Q5

EH1600L

Record mode

Normal Event

Division Res Fps Q Res Fps Q

Program

A D1 7 Q5 D1 7 Q5

B D1 4 Q5 D1 4 Q5

C D1 2 Q5 D1 2 Q5

D Half 15 Q5 Half 15 Q5

E Half 7 Q5 Half 7 Q5

F Half 4 Q5 Half 4 Q5

G CIF 30 Q5 CIF 30 Q5

H CIF 15 Q5 CIF 15 Q5

I CIF 7 Q5 CIF 7 Q5

Install&User Manual

５４

4 Monitoring

All analog video image channels connected to eDVR is displayed to screen by Power

connection. It is to utilize all monitoring mode of DVR.

4.1 Basic Screen

After Power connection, the DVR operates on

automately.

It boots with LED on.

After booting, 16 channel screens are

displayed.(EH1600L, LH1600C : 16screens,

EH800M,LH800L:9screens, EH400H: 4screens)

※ If there is user password set, Password input

window will be displayed.

4.2 Single Fll Screen Mode

Press the channel number wanted or click

mouse button.

Press [MULTI] button to return to divisional

screen.

4.3 Multi Screen Mode

Press [MULTI] for multi channel display or click

“Display” icon from Function menu.

Press [MULTI] button every time, screen mode for EH1600L, LH1600C is changed to 1~4,

5~8, 9~12, 13~16, 4C, 1~9, 8~16, 1~10, 16 screens, and for EH800M, LH800L is 1~4, 5~8,

4C, 9screens, and for EH400H is 1~4screens.

4A, 4B, 4C, 4E, 9A, 9B, 10A, 16 channel division. (MD800E : 4E, MD400E : not supported).

Install&User Manual

５５

4.4 Screen Description

The status bar from monitoring screen, it shows DVR’s current status that included Date/Time,

Record, Motion/Sensor Detection, Manual Record, Text input and HDD’s record capacity.

4.5 Auto Switch Mode

There are System Standard modes and User Defined mode in Auto Switch mode. And Users

Sequence mode operates by the press [SEQ] button.

4.5.1 System Standard Mode

By [Auto] button, it can monitor auto switching of all channels.

Press [MENU] for the setting switching term or using mouse click menu icon from function

menu.

Move to “Device” “Monitor” from OSD menu.

Select “Seq. Switching(sec)” and set value from 1 sec. to 60 sec. At OFF set, auto switch

mode does not operate.

Install&User Manual

５６

Auto Switch mode can be set in every division mode by the press [Auto] button.

Press [Auto] button once more to leave from Auto Switch mode.

4.5.2 User Sequence Mode

Press [AUTO] button or click [Sequence] icon from Function menu with mouse.

- Auto Switch model can be set from “Monitor” main menu.

Install&User Manual

５７

User mode can define max. 16 channels.

As shown above picture, the 16ch DVR can be define between channel 1 ~ 16, the 8ch DVR

from 1 ~ 8 and the 4ch DVR from 1 ~4.

4.6 Event Screen

When there is an event occurred, the green color [M] and red color [S] will be display from

status bar. In case of [M] displayed, the camera name will be turned to green color, and it will

turn to yellow when Motion Detection event finish.

In case of [S] displayed, the camera name will be turned to red color, and it will turn to yellow

when Sensor event finish.

It can be set to Pop-up automatically relevant screen when alarming.

Set pop-up period can be set into “Alarm Pop-up (sec)” inferior to “Monitor” menu.

At the simultaneous alarming in several channels, it displays the division as many channel as

alarmed. For example, when 3 channels alarm, 4 divisions is displayed on screen. And press

any button to return orginal channel.

Install&User Manual

５８

1. If Alarm Pop-up Hold (sec) set to Off, Alarm Pop-up will not operate.

2. If Alarm Pop-up Hold (sec) set to Keep, it does not return to previous screen before press any

button

4.7 Zoom Screen Mode

- From single full screen mode, press [FUNC] and D-Zoom button then select + button to

activate zooming the image.

- Default zoom screen locates to main center when press [ZOOM] button. Zoom image can

shift left-right in 18 steps and top-buttom in 12 steps.

- Use directonal key button to screen move.

- Press [-] one more to return to original screen.

4.8 Pause Live Screen

- Live screen can pause like PlayBack.

- Press [PAUSE] to pause live screen and press [PAUSE] to return live screen.

Install&User Manual

５９

4.9 PTZ Control

Connect PTZ controller to DVR and set relevant

protocol from “Serial Setup” menu, then PTZ can

operate while monitoring live images.

The method of operating PTZ, press PTZ button from

DVR’s front panel, or click PTZ icon from Function

menu.

Below lists are the protocol available in DVR.

Model Manufacturer

BOSCH AutoDome, TC8560X-4

Bosch

PELCO(P), PELCO(D)

Pelco

Sony EVI-D3x

Sony

VT VPT-4x

AD SpeedDome

SungJin SJ372R1

SungJin

Samsung SCC641

Samsung Electric

Panasonic WV-CS850

Panasonic

SDZ160/330, Samsung SPD,

Keyboard SCC3000A, Samsung SRX-100B

Samsung Techwin

LG GAC-PT2

Keyboard KBD300A, WGI SPD1800/2600

Webgate

WKC-100

Webgate

Merit-Lilin FastDome

Merit

Elmo PTC200C

Elmo

Canon VC-C4

Canon

HTC-230S

DongYang Unitech

RVision

Elbex

Honeywell 755/655, HRX-2000, HTX-3000,

ScanDome2

Honeywell

VIDO

VICON

Vicon

Hunt

ORX-1000

Sysmenia

Install&User Manual

６０

Fine CRR-1600

LiveEye

Tokina

Kodicom KRE

Kodicom

Nuvico

- Press desired channel button.

- Press PTZ button from front panel or click PTZ icon from function menu with mouse.

- PTZ menu (Pan/Tilt, Zoom/Focus, Load Preset, Save Preset) will be appear.

- Then press [Enter] button or click from mouse.

4.9.1 Pan/Tilt

This menu is used to control Pan & Tilt function at real-time monitoring mode.

- Select Pan/Tilt from PTZ mode.

- Control Pan/Tilt through directional key at front part.

4.9.2 Zoom/Focus

This menu is used to control Zoom & Focus function at real-time monitoring mode.

- Select Zoom/Focus from PTZ mode.

- Control Pan/Tilt through directional key at front part.

4.9.3 Load Preset

This menu is used to shift to Preset Set at real-time monitoring mode.

- Using up / down button or mouse wheel to select the Preset Number.

- Once preset configured then select Load and press Enter or click from mouse.

4.9.4 Save Preset

This menu is used to set new Preset at real-time monitoring mode.

- Control camera location using ‘Pan/Tilt’ and ‘Zoom/Focus’ menu.

- Using up / down button or mouse wheel to select the Preset Number.

- Once preset configured then select Save and press Enter or click from mouse.

4.9.5 Auxiliary On

This menu is used to utilize specific function in PTZ device at real-time monitoring mode.

- Using up / down button or mouse wheel to select the Aux Number.

- Press relevant Number button of specific function (Aux function is available to max 16

functions.)

Install&User Manual

６１

4.9.6 Auxiliary Off

This menu is used to stop operation of specific function of PTZ device.

- Using up / down button or mouse wheel to select the Aux Number.

- Select Off and press Enter button or click from mouse.

4.9.7 Menu

It is to go into connected PTZ’s menu, using up/down/left/right and enter key from front panel for

setting the menu, and press ESC button for exit the menu.

Install&User Manual

６２

5 Playback

5.1 Playback Mode

5.1.1 Playback on Standard monitor (16 / 9 / 4 division)

- Please, push play button in monitoring mode or mouse click play buttion in Function menu.

- If pushing Play button or FWD button, video playbacks in forward direction at 1× speed.

- If pushing REW button, video playbacks in reverse direcetion at 1× speed.

- If pusing Playback button in multi-division monitor mode, it playbacks the recorded data

as 16 / 9 / 4 division screen.

5.1.2 Playback function

PLAY : Playback 1× speed. If using mouse, click Play button in Function

menu.

Multi channel video will play back if pusing [PLAY] button in monitor

mode. And it playbacks from the latest played back.

PAUSE : Pause playback temporary. With mouse, click Pause button in

Function menu.

STOP : Stop playback. With mouse, click Stop button in Function menu.

FWD : Playback speed will be changed. (x1, x2, x4, x8, x16, x32, x64, x1/2,

x1, x2, x4 – in order), If pushing [FWD] button in live view, it plays back

video 1 minute ago. Playback speed can be chanbed by pussing

[FWD] button.

REW : Reverse playback speed will be changed. (x1, x2, x4, x8, x16, x32,

x64, x1/2, x1, x2, x4 in order)

If pushing [REW] button in live view, it plays back video 1 minute ago.

Playback speed can be chanbed by pussing [REW] button.

STEP FORWARD : If pushing [FWD] button on Pause mode, playback by each frame to

the forward. Push [PLAY] to return normal playback.

STEP REWIND : If pushing [REW] button on Pause mode, playback by each frame to

the reverse. Push [PLAY] to return normal playback.

1/2 REWIND : Play back at a half speed to forward direction.

1/2 FORWARD : Play back at a half speed to reverse direction.

Install&User Manual

６３

5.2 SEARCH MODE

This menu is to playback specific time data from the time frame and searching log at Playback

mode.

There are Time, Calendar, Event, Thumbnail mode.

Please, push Search button on the front panel or click in Function menu.

5.2.1 Time Search

Select date and time to search and playback video will be moved to the selected point.

Start-REC Time : The date and time of start-recording

End-REC Time : The latest date and time of the recording

Search Time : Select the range of date and time for Search

Search : Execution button

5.2.2 Schedule Search

Install&User Manual

６４

EH1600L, LH1600C EH800M,LH800L

EH400H

Depends on models, EH1600L, LH1600C shows the status of recording for 1~16ch, EH800M,

LH800L for 1 ~ 8ch, EH400H for 1~4ch.

Year : Select Year to search. With mouse wheel, user can change it.

Month : Select Month to search. With mouse wheel, user can change it.

Date : Select Date to search. With mouse, select the date and decide the

time by wheel.

Time : Select the time and push Enter button to plya back.

5.2.3 Event Search

User can search by all channels, some of channels, all events, motion detection, sensor in

certain range. For change of date and time, with front panel, plese use top and down button. In

case of using mouse, scroll the mouse wheel after selecting area. Searched result will be

displayed on additional event window. Select and push enter or scroll the mouse wheel to move

to the wanted date and time area.

Install&User Manual

６５

Start-REC Time : Starting date and time of the recording.

End-REC Time : The latest date and time of the recording

Search Start

Time

: Input start date and time for search with direction button and push

Enter and change the value by Up and Down button. With mouse, click

and scroll the wheel.

Search end Time : Input end date and time for search with direction button and push

Enter and change the value by Up and Down button. With mouse, click

and scroll the wheel.

Event Channel : Select the channel for search

EH1600L, LH1600C from Ch1 to Ch16

EH800M, LH800L from Ch1 to Ch8

EH400H from Ch1 to Ch4

Event Type : Select the event type for search

There are all events, motion detection,sensor, video loss, text type

5.2.4 Thumbnail Search

Search certain channel by thumbnail type. If select the searched thumbnail, selected date and

time video will be played back.

Channel : Select the channel and change the value by direction key or mouse

wheel.

Install&User Manual

６６

Start Time : Input the date and time for starting search and change the value

using up-down direction key or mouse wheel.

Interval : Set Interval value by Up-down button or mouse wheel.

View video : If pushing search button, 16 cycles will be shown based on start time.

Press [Func] to return to the search or use mouse wheel.

Select video : Play back from the selected video of thumbnail search result.

With pressing Enter or clicking mouse, use can play back.

5.3 Copy

This is for copying recorded video. There are CD/DVD and RE4 and AVI type.

Copy function is supported to be used by user who has the authorization. For authority

configuration, please, refer to 6.9.3 Security.

To use copy function, press [COPY] or Click Copy button in Function menu.

In case to copy with RE4 and AVI format, you need to use USB memory stick or USB HDD.

You must do “Fat32” format first from PC before doing copy.

5.3.1 CD/DVD

This is copy function by using CD or DVD. CD or DVD will be automatically searched.

Type : Selec CD/DVD using up-down direction key or mouse wheel. Press

Enter and scroll wheel to change the value.

Channel : User can select some or all channel among 16channels. Select the

channel location and press Enter or use mouse wheel.

From : Select start date and time to copy using up-down key or mouse

wheel.

To : Select end date and time to copy using up-down key or mouse wheel.

Install&User Manual

６７

Select Disk : Select the media to copy using Enter buttonr on Select Disk.

Start : Start Copy. Press Start button with Enter or click the left button of the

mouse.

Please, refer to the supported media list below.

DVD-R manufacturer CD-R Manufacturer

Mitsubishi(×16 recomended) Mitsubishi(×52 recomended)

TDK(×16 recomended) TDK(×52 recomended)

Imation(×16 recomended) Imation(×52 recomended)

Sony(×16 recomended) Sony(×48 recomended)

5.3.2 RE4

User can back up by HDD, USB memory and play back suing mini-player or Control Center.

Select channel position and press Enter or use mouse wheel to open the channel list like below.

[EH1600L, LH1600C] [EH800M, LH800L] [EH400H]

Type : Select RE4 using up-down button or mouse wheel.

Channel : To pop up the channel selection window, press Enter or use mouse

wheel.

Select Channel : use can select some or all channels and after selecting channel,

press Enter or click mouse left button.

Start time : Set start date or time to copy. After selecting part for change and set

Install&User Manual

６８

the vaule using up-down key or mouse wheel.

End time : Set End date or time to copy. After selecting part for change and set

the vaule using up-down key or mouse wheel.

Select disk : Select media to copy. Press Enter on Disk list or click mouse.

Start : Start copy. Press Enter or click mouse.

Reference : not perfectly finished backup file will not be played back in PC.

5.3.3 AVI

Use USB memory or HDD to copy certain part.

Type : Select AVI using up-down key or mouse wheel.

Channel : Select the channel to copy by up-down key or mouse wheel.

From : Set start date and time to copy. Time and Year by left/right button and

date/time by up/down button. With mouse, click left button first and use

wheel.

Duration : Set copy length. Copy as selected time length from the start using

up/down key or mouse wheel.

Select disk : Select media to copy. Press Enter and select media or click mouse.

Start : Start copy. Press Enter or click mouse.

Caution : If copied file is not played back, please, install integrated codec first.

Install&User Manual

６９

6. Configuration

6.1 Recording Structure

There are 4 modes in DVR recording. Configuration relation structure is like below.

Please, refer to the below each item for detailed recording configuration.

6.2 System Setup

Time and Disk and authority can be configured.

6.2.1 Date/Time

Time set should be configured prior to the recording.

Time configuration is very important to pretect the recording data. Time change on recording is

not recommended. Time zone configuration value of factory default is “UTC 00:00 Dublin”

Install&User Manual

７０

6.2.1.1 Time Setup

Caution: under recording, if user changes Time, it will affect time change on previously

recorded video data in accordance with. Therefore, we recommend backup before time

change.

- Press Main Menu of Function or [MENU] button on the front panel.

- Move to “quick setup” menu.

- After selecting “Time” in Quick setup and press [Enter] or click.

- Menu of time configuration 6.2 will be opened

- To move to the sub menu, use directional key or mouse.

Time zone

Use left/right direction key or mouse wheel. To return to previous menu, press [ESC] or click

right mouse button. (It is same as OSD menu)

Daylight saving

This menu is synchronized with time zone configuration menu. It means when daylight saving

area is set, this function works. Daylight saving applicable area is all the same with Time zone

of Micorsoft Windows.

Date format

With using left/right diection key or mouse wheel, configure date among “MM/DD/YYYY”,

“YYYY/MM/DD”, “DD/MM/YYYY”.

Time

With left/right direction key, use can move to year,month,day,hour in order and each

configuration will be controlled by up/down key or mouse wheel.

Apply

User must push “Appl Date/Time” button. And you will see the below message box.

Install&User Manual

７１

Except date/time configuration, other configuration records automatically, but

“date/time” configuration influences critical effect to HDD recording file system,

It doesn’t record automatically. To apply the changed value, user must press

[apply] button.

6.2.1.2 NTP Setup

NTP(Network Time Protocol) make time of connected devices synchronized. There are NTP

server and client which get time signal from the server.

Sync NTP

Set NTP function on/off.

NTP Mode

Configure NTP mode of DVR – Client / Server / All

NTP Server Loc.

When NTP mode is client, it is on Enable. Configure yes or no wether NTP server is in Local

Network or Public.

Install&User Manual

７２

NTP Local server IP

In NTP local server Enable, configure server ip. Input IP address of NTP server or DVR set by

NTP server In local network.

Interval

Configure interval of time sync.

Caution: If use NTP client mode, user must set NTP on.

6.2.2 Disk

It explains how to add or remove or format internal or external HDD.

Over Write(Auto Deletion)

If there is no space in HDD, old data will be deleed automatically.

Block Playback

This function makes recording data seen during the limited area.

For instance, if seting block playback by 2 day(Pic 2) among 10 days, Just allowed 2 days data

can be played back.

Disk Full Alarm Warning

Install&User Manual

７３

If mounted Disk is full, alarm warning to user.

6.2.2.1 Disk

This is menu for the management of internal or external HDD.

Manage status, bad block, size, Yes or No etc.

Type : display location or type of disk.

Int A (Internal A HDD), Int B (Internal B HDD), Ext (External HDD)

Model : HDD model name.

Bad Blk : display bad block. In HDD. If no proble, “0” will be displayed. Others are

Not shown anything at all.

Size : Display HDD size by MB unit

Enabled : Make HDD enable mode or disable mode.

Yes: enable / No: Disable

In case HDD YES

- Enabled : Press [Enter] in No mode or scroll mouse wheel. Notice window pops up and show

user the message like below.

- Caution : This Disk is not available without format. Will you format Disk?

- If selecting No, keep previous data and HDD will be Enable to use.

- If selecting Yes, delete previous data and HDD will be Enable to use.

In case HDD No

- Enabled : In Yes mode, press [Enter] or scroll mouse wheel and notice window pops up and

show user the message like below.

-Caution, will you remove Disk?

- If Yes, user will find the message “Disk is removed” on the bottom and Enable status

will be No.

Install&User Manual

７４

- HDD is not used.

- If No, keep previous HDD without change.

6.2.2.2 Disk Status

Temperature and status of HDD will be shown.

6.2.3 User Setup

There are administrator and user and administrator can use all functions. The max. number of

user is 10 person. Each user can use the function allowed.

Check

If Check item is configured all by X[Check-1], all users can use all functions.

[Check-1] [Check-2]

In the other hand, if all are set by O[check-2], all users can use the functions in accordance with

Each users authority.

For example, as you can see the below picture, User1 can use PTZ, Relay off, power On,

N/mike functions are available, user 2 just can use menu and N/mike functions.

Install&User Manual

７５

Admin Password is “12345” in factory default and from user 1 to 10 in order

“11111”,”22222”,.. and user10 is “00000”. In case of 9 channel DVR user, press “0” for

figure 0, in case of 16 channel, press button “10”

Password change

Select user  Input password and press change  Press Yes

Password input box is displayed. Password can be input with front figure button or text input

window. After inputing 8 digit figure, click “Change” button.

After that, message pop up window will be shown and press “Yes”.

Authority

User can use only authorized functions.

If user 1 has PTZ use authority, when pushing PTZ button, authority check window will pop up

and user should inpt the password and if it is correct, user 1 can use PTZ function. If password

is wrong, message box “Wrong password” will be displayed.

Install&User Manual

７６

[Authority Check]

[Wrong password message]

6.2.4 Utility

Configure the name of DVR, remote controller ID, Language.

DVR Alias

Set the name of DVR.

DVR Keyboard ID

This menu is to set the address of keyboard when using all functions of DVR by keyboard.

Factory default is “1”. If user want to control various DVR by one keyboard, its address should

Install&User Manual

７７

be set with the different value.

Remote Controller ID

Max 16 remote controller ID can be set and one remote controller can manage 16 DVRs.

Registration order for Remote controller.

- Make remote controller direction to DVR.

- Press ID button and figure in accordance with configured remote controller ID.

- If IDs are matached correctly, DVR buzzes.

- Use Remote controller.

Language

Select Language to use.

Firmware Update

Can update firmware by USB Memory.

- Insert USB memory to USB port.

- Press Firmware Update button.

- Select [YES] on the pop up window.

- System will reboot.

- Firmware update is done.

System Log

System Log shows boot status of system and user and configuration etc.

Install&User Manual

７８

Factory Reset

Change all configuration value by factory default.

Caution : Only administrator is allowed.

6.3 Network

This is menu for configuring network.

Install&User Manual

７９

Type

Configure type of Network (Ethernet/xDSL). If connected to cable modem or Lan directly to DVR,

configure by “Ethernet”.

If DVR connects to xDSL- one of PPPoE type, configure xDSL. But if it is not type of PPPoE,

configure ‘Etherent’.

DHCP

With DHCP (Dynamic Host Configuration Protocol), all hosts connected to Lan can get Public IP

address temporary.

If LAN has DHCP server and it is active, DHCP server allocate IP address to DVR.

Mostly middle and large network use DHCP server in LAN, but in case of small network,

NAT(Network Address Translation) of HUB is general.

IP Addr

IP Address is for the connection between DVR and Control Center and also for web

connectionfrom Webviewer. (But, Net Mask, Gateway should be configured.)

Net Mask

Net Mask makes range of IP address available. It should be received from network

administrator.

Gateway

Gateway is necessary to communicate IP, it should be received from network administrator.

DNS1

DNS1 is mandatory item to regist and use SWR and it should be asked to network administrator.

Additional DNS

Additional DNS is alternative when DNS1 has a problem.

Port

Port is necessary for Control Center and Webviewer connection.

Reference : Basic port is 80 and if using PPPoE modem and AP, be careful typing port

number.

Install&User Manual

８０

Bandwidth

Menu for configuring network data transmission capacity. Without any additional configuration, it

works but if user want to set, please, ask for administrator.

6.3.1 xDSL

DVR is connected to xDSL line and use PPPoE type, please change type by xDSL and

configure user ID and Password. User ID and Password should be same as xDSL.

User ID/Passwod

Configure user ID and Password.

Status

It shows connection status of DVR.

6.3.2 WRS

If eDVR is connected to Cable modem or xDSL modem, IP address is changed at every

connection to ISP. In this case, changed IP address can not be known. If eDVR using static IP

To register Static IP to WRS, please refer the following to set.

Install&User Manual

８１

WRS Interval

For continuous registery, register inverval should be set to ‘WRS Interval’. According to set

value of static IP address, it renews the information in WRS server regularly. If user registers

the interval ‘0’ or eDVR does not transmit any data for 2 days, the data is removed from WRS.

WRS URL

This menu is to set server address to register. WRS addresses that WebGate operates now are

www.webgateinc.com or mycam.to.

6.4 Device Setup

This menu is for configuring each camera connected to DVR.

There are [name][Status][Color/balck or white][Brightness][Contrast][PTZ] etc.

Caution : NTSC and PAL camera can not be used at the same time.

If changing the camera from NTSC to PAL, system should be rebooted.

Configured value will be applied to monitoring and search at the same.

Install&User Manual

８２

6.4.1 Camera Setup

Select the camera to configure in Channel menu.

6.4.1.1 Title

Configure camera name.

If pressing [Enter] button or click mouse, test menu will be shown.

For text string, text input box will be shown.

- Use directional key for text input.

- With mouse, just click the text.

- Select the text using up/down and left/right button.

- After selecting the text, press [Enter].

- To delete the text, press [] button.

- To make a space between letters, press [].

6.4.1.2 Using Channel

Configure wether using camera or not.

After pressing [Enter], select it using left/right key or mouse wheel.

If user wants to enhance the recording or network monitoring speed, please, set the channel

disable.

6.4.1.3 AGC (Auto Gain Control)

AGC is the function to control the range of video signal input from carame connected.

Configure Enable/Disable using directional key or mouse wheel.

6.4.1.4 Brightness/Contrast

It can control Brightness and Contrast of video. After press [ENTER], use left/right button or

mouse wheel to set the value wanted from each “–9” to “+9”.

Install&User Manual

８３

6.4.2 Monitor Setup

Main monitor provides all function which DVR supports and with spot monitor can use single

channel conversion.

Covert channel

With Covert menu, user can covert the channel in Live/Playback mode

In Covert menu, all channel list will be shown and press [Enter] buttion and click mouse to tick

the channel. Checked channel will not show the video in Live/Playback.

User sequence configuration

User sequence can be edited. There are 16 user sequence mode and its interval is from 1 to

60seconds.

Multi mode

EH1600L, LH1600C have predefined screen modes. 4E(4channels), 9B(basic 7 channels and

additional 2 channels),10A(10 channels). In case of EH800M, LH800L, it can use only

4E(4channels) and EH400H doesn’t provide multi mode.

The way to composing

The way to conpose screen is selecting the target and after selecting right window and press

[Enter] button or use mouse. If channel selection is down, press [ESC] button or click mouse

light button.

DVI Resolution

There are nine resolutions – EH Series : 800x600@56Hz, 1024 x 768@60Hz, 1280 x

720@50Hz,1280 x 720@60Hz, 1920 x 1080p60, 1920 x 1080i50, 1920 x 1080i60, 1920 x

1080RB, LH Series : 800x600@56Hz, 1024x768@60Hz, 1280x1024@60Hz

Install&User Manual

８４

Display information

Display information is to configure which information will be shown on live view and playback

view. In live view, time,channel name, event, recording status, HDD, remote controller ID, text

can be set and in playback view, time,command,channel name, event, text can be configured.

6.4.3 Audio Setup

With this menu, user can configure Voice Channel, Audio recording, Volume, Synchronization,

Mixing.

Voice Channel

Select audio to use

Recording

Configure yes or no of using audio recording. If no, audio will be out only in live view and if yes,

Audio will be out in both view modes.

Volume

Configure volume by +, - direction

Synchronize Video Channel

Configure which channel is matched with the input audio. But this function is applied only on

recording. Audio out in live view will be covered in Voice Mixing below. Default set is Auido no.1

to channel no.1.

Voice mixing

Install&User Manual

８５

Select audio in live view. If setting by “All”, input audio will be out in eery channels and if

configured certain channel, input audio will be out on the selected channel only.

6.4.4 Text Setup

Configure Text in Device menu.

Recording

Set On/Off of recording against Text input

Sync Text with

Select channel to synchronize with text.

Header check

It has the various type of data input from the external device (Access Control, POS, ATM etc).

Like VSI Pro, VSI Pro Hydra, Star Finger 007, it is not needed when the protocol of these device

have implemented on the device. If not, this is the parameter to analyze how the one of data is

constructed from the text data that is input continuously.

Namely, all data has the first and the end. Header indicates the information that already inserts

to inform its starting. Therefore, Header information is defined here to acknowledge its starting

Install&User Manual

８６

of a data. The reason of 2 Header is to detect maximum 2 data out because each device can

output various datas.

Delimiter

Delimiter value can be different according to the manufacturer, please, refer to the product

manual or seller.

Time out

Following lines defined here means maximum number of text line from one data. Even if there is

standized data, there can be a short and long data. For example, there are 3 lines to write

names on ATM. But some may need only First name & Last name to register. Which it means

requires only 1 shorter than other ATM users. It is to decide the last line of the one data

eDVR can not recognize it automatically.

Lines

Define how many lines will be shown.

Caution : external device can not be recognized, please, ask to the seller.

6.4.5 Serial Setup

DVR has 3 serial port. One is RS-232 and the other 2 ports are RS-485.

Serial Port

Select Serial port.

Device

Select the connected device.

Install&User Manual

８７

Interface

Configure which interface user uses.

COM1 is to RS-232C, COM2, COM3 are to RS-485.

Baud rate/Parity/Stop Bit/Data Bit

In put suitable value according to external device.

6.4.5.1 PTZ Setup

Additional configuration for PTZ Address, PoirtPTZ

PTZ Home

Shift to Preset assigned if it has no movement in certain time while PTZ control.

PTZ Idle Time

If it has no movement during configured time, shift to PTZ Home.

PTZ Port

Select Port for PTZ

PTZ Address

Configure the address configured in PTZ.

6.5 Event Setup

There are 5 items such as event, Text, Sycn Event,Preset, System event.

Install&User Manual

８８

6.5.1 Event Check

There are 3 items – Always, not apply, Timezon.

In case of Timezone, with similar configuration window like schedule, user can configure event

per weekday/time.

• INDEX : Schedule configuration from 1 to 50

• Weekday

• Time

• Delete : delete INDEX

How to configure

If configuring INDEX,weekday,time, they are displayed on the table.

If clicking and selecting start time and end time of recording on the table, Index,weekday,time

will be shown on the table.

How to delete

Select INDEX and click Delete buttion.

If clicking Delete buttion without selecting INDEX, previously selected INDEX will be deleted

and from the latest INDEX, it will be deleted in order.

How to change

Install&User Manual

８９

After selecting INDEX, change directly weekday,time.

6.5.2 Sync Event

Configuration for Event synchronization.

Event Action

There are 6 actions – relay 1 to 4, buzz, E-Mail.

Action Duration

Action Duration runs if relay and buzz are configured, and goes on during the configured

time. E-mail works by configured time interval.

Normal Event Source

User can configure Sensor, motion detection,V-loss,Text.

Modle Sensor MD V-Loss Text

EH1600L

LH1600C

16 16 16 1

EH800M

LH800L

8 8 8 1

EH400H 4 4 4 1

Install&User Manual

９０

System Event source

System Event source can configure Bad block, Disk full, Fan error, authorization failure,

WRS registeration failure.

E-Mail

E-mail address

Input E-mail address to get event alarm by E-Mail.

Install&User Manual

９１

Sender Address

Not mandatory but necessary for receiver to find out which DVR sends event.

Including Picture

In general event, when sensor, MD, V-loss events are generated, the event information and

channel video will be sent to e-mail together.

But system event just send system event information.

6.5.3 Motion Detection

Channel

All or certain channel.

Sensitivity

Sensitivity can be configured from min.1 to max 10.

Area

Select detection area.

User can select all or certain channel.

User Area

When selecting per channel, it can be configured.

1 grid size is 22x15 and factory default value is All. If pushing user area, configuration

window for detection area.

Install&User Manual

９２

With direction key, select area and press [Enter] or click mouse. And press “ESC” button or

click right mouse button, shift to the previous menu.

6.5.4 Sensor

This menu is to setup the existing sensor input and type of sensor.

EH1600L, LH1600C have 16 inputs and EH800M, LH800L have 8 inputs and EH400H has 4

inputs.

Sensor has 2 types, Normal Open(N.O.) and Normal Close(N.C.).

6.5.5 Preset

In PTZ function, make configured preset work according to sensor input.

Please, configure preset per PTZ.

After selecing channel in preset menu, select event to work preset.

Event can select sensor,MD,Text, its preset can be configured up to 16.

Install&User Manual

９３

Install&User Manual

９４

6.6 Recording setup

There are 3 mode for recording – schedule recording, manual recording, event recording.

Schedule recroding records according to the configured schedule. And manual recording

records via pushing “REC” button and event recording records when events are on.

6.6.1 Program setup

Using [Program], adjust frame rate and quality and resolution and configure recording program

for Manual&Event&Schedule.

[EH1600L, LH1600C] [EH800M,LH800L]

[EH400H]

In event recording, one channel can record up to its max frame rate and if setting 2 channels

as event recording, their recording frame rate will be adjusted automatically.

Program

There are 26 programs from A to Z composing recording quality and resolution per channel.

Please, refer to 3.5 programe configuration value.

CH (Channel)

Display the channel figure.

R (Resolution)

Install&User Manual

９５

There are 3 resolutions - D1(704x480), Half D1(704x240), CIF(352x240)

F (FPS)

It means frame per second and can select 1 to 30fps. Max. frame can be changed according to the configuration.

Q (Quality)

There are 5 recording quality - Q5/Q4/Q3/Q2/Q1. Recommended quality for event recording is Q3.

Max R/F

Max R/F shows the number of frame available according to the selected resolution. For instance,

if it is set by 30fps at CIF, it means that the channel can record up to 30frame at CIF

resolution.

Reference : how to calculate recording performance

D1[704x480] = 2 x Half D1[704x240] = 4 x CIF[352x240]

If 480 frame can be recorded at CIF resolution, instead of it, 240 frames at Half

D1 and 120frames at D1 resolution are possible.

• In case that the channel is configured as disable

Configuration method : Menu > camera configuration > channel : “Disable” – (the channel in gray)

For example, all channels can be configured as 30fps at CIF all the same. If one channel is configured

as disable, system has resource avaiable as much as 30fps at CIF. And if conbining it with other 30fps at CIF, other channel can be

configured as 30fps at Half D1.

• In case that the channel is configured as 0 fps.

Another channel can not use resource room as much as CIF 30fps. It is because the channel configured as 0 fps needs 2~3fps

at least for network..

Reference : the relation in between general recording and event recording.

When Event is triggered, records event recording according to the configured value. Recording

Performance of DVR depends on the product. For example, if MD1600E is set as manual

recording at CIF 480fps and event recording at CIF 480fps, it can not be over CIF 480fps.

Therefore, it should be configured within CIF at 480fps resource.

• Event configuration value on CIF 480fps

If you configure recording all channels at CIF 30fps, available event recording confirguration

is CIF 30fps, Half 15fps, D1 7 fps.

If you want to configure channel no.1 as D1 30fps, you should adjust the other channel

Install&User Manual

９６

recording configuration.

• On event recording of multi channel

With mulity channel event recording, if configured recording value is over the system max

performance, general reconrding will keep their recording configuration and event recording will

be balanced down equally.

6.6.2 Manual/Schedule recording setup

With the change of recording mode, manual recording or schedule recording can be at one’s

choic.

And their resolution , frame rate , quality will be in accordance with the program.

6.6.2.1 Manual Recording

Only in manual & event recording, manual recording runs and when pressing [REC] button,

recording starts. If you want schedule recording, recording mode should be Schedule & Event.

[EH Series] [LH Series]

6.6.2.2 Schedule Setup

It records according to the programmed schedule automatically. Make recording mode Schedule

& Event and configure day and time.

Install&User Manual

９７

check and select each program default vaule and select one of 26 program from A to Z or

several programs. Below picture show program A.

• INDEX : Schedule unit from 1 to 50

• Weekday : Set the day applicable

• Program : Set recording program(A~Z)

• Time : Set time applicable

• Cancel : Cancel per INDEX

Configuration

Configure INDEX, weekday, program, time.

If selecting recording start time and end time on the table by mouse, its Index,weekday,program

will be displayed.

Deletion

Select INDEX and click Delete button.

If clicking delete button without INDEX, previously selected INDEX will be deleted first and after

that, from the largest INDEX in order.

Install&User Manual

９８

Edition

Select INDEX to edit and change weekday, program,time directly.

In case that INDEX 50 are all configured, select the time zone to change by mouse click and

click the time again, previouse configuartion will be deleted and new configuration will be shown.

Caution : If selecting the same time twice, “!” will be shown on the chart.

When configuring time sector, previously configured time can not be included.

De-interlace

Set playback deinterlace On/Off.

It works on Full Dq recording. In “On” status, screen vibration of paused Full D1 video will be

redcued.

6.6.2.3 Event recording setup

Select resolution and frame rate and quality for event recording.

There are 4 trigers – Sensor, Motion detection, Text, Digital input.

First, select the program and check resolution and frame rate and quality of the channel.

(refer to 6.6.1, program configuration)

Event recording can syncro manual&event, Scheduel&Event.

Select among Manual&Event, Schedule&Event in “Recording mode” of [Record configuration]-

[recording]

Reference : Please, check below to configure event recording.

1. Select one of Manual&Event, Schedule&Event.

2. In program configuration, set frame rate by 0 fps in general mode and only

configure Event frame rate.

Install&User Manual

９９

3. Set Event applying time.

Event Time configuration

Configure time for event recording and there are 3 mode – Always, no use, Timezone.

In “Always”, event works all the time and in “Timezone”, works during configured time.

Configuration of Timezone is similar with schedule configuration and can configure

weekday,time for Event.

• INDEX : Set from 1 to 50

• Weekday : Set weekday applicable

• Time : Set time applicable

• Deletion :Delete per INDEX

Configuration

Configured INDEX,weekday,time will be shown at once.

Select recording start time and end time in order and its INDEX,weekday,time will be shown.

Deletion

Select INDEX and click Delete button

If clicking delete button without INDEX, previously selected INDEX will be deleted first and after

that, from the largest INDEX in order.

Edition

Select INDEX to edit, and change the values.

In case of being configured by INDEX 50, click and select time to eidt and if clicking the time

table again, previous configuartion will disappear and new configuration will be shown.

WebGate EH1600L, EH800M, EH400H, LH1600C, LH800L User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual