1
Caution for installation and usage
1. Precautions for different DVR
Please use it with the corresponding PoC DVR. With PoC(Power over Coax) function, the
DVR is able to supply camera with the power. And with CoC(Control over Coax) function,
the DVR is able to send RS485 to the camera
- PoC DVR : When connecting to WEBGATE’s PoC DVR, only the coaxial cable is needed
between the camera and DVR to supply power and send RS485.
- Non PoC DVR : When connecting to Non PoC DVR, please separately connect DV12V to
the camera.
2. Check Frame rate setting based on power frequency
- Set Frame rate to 25Hz if your region is using 50Hz(PAL) power frequency, or set to 30Hz
for 60Hz(NTSC) region. (OSD : System Frame rate).
3. Focus setup
To aviod losing focus at night time, please adjust camera focus as follows.
1) Connect OSD remote controller on the back of the camera.
2) Press [SET] on the OSD remote controller and select “FOCUS ADJ” to enable “Adjust
Focusing” mode.
3) Use the lens’ lever to adjust zoom and focus. (※Check the Focus Gauge)
4) End the “Adjust Focusing” mode by pressing the [SET] on the OSD remote controller.
※ What is Focus Gauge?
When the user is manually adjusting the focus, the camera shows graphical bar to have
the user look at the focus visually. When the yellow and green bar meets together,
that’s where the camera is focused.
4. Shutter mode setup based on installation environment
- INDOOR : Controls brightness for the best video quality at indoor environment.
- OUTDOOR : Controls brightness for the best video quality at outdoor environment.
- INDOOR/OUTDOOR-ANTI BLUR : Improves the motion blurring phenomenon than
Indoor/Outdoor mode under dark environment but the brightness decreases relatively.
5. Do not expose this camera to rain or moisture to prevent malfunction, fire and shock
hazard.
6. DC12V(500mA over) power adapter must be used.
7. Please contact to qualified service personnel in case of product damage. Do not
attempt to repair product by yourself.
8. Please avoid external shock and vibration on the product.
9. Do not install product under excessive heat or cold environment. (recommended
operation temperature is -10°C~50°C)
10. Do not target lens to the sun. Image sensor might be damaged
11. Do not open the product under any circumstances, it could void the warranty. Natural
disaster like li
g
htning, flood will need charge for repair.
English
2
Feature
PoC / CoC
PoC(Power over Coax) : WEBGATE PoC DVR supplies camera with power through
connected coaxial cable.
CoC(Control over Coax) : WEBGATE PoC DVR supplies camera with RS485 without
additional communication line. Allowing OSD control, zoom, focus, f/w upgrade and more.
※ All PoC supported cameras support CoC function as well.
2MP, Full HD high resolution picture quality
Full HD(1920x1080) provides 6 times higher resolution than SD level camera, and more
clear video image can be achieved through 1/3”, 2Megapixel progressive CMOS.
High performance under low light environment
High performance quality can be achieved under low light environment by optimizing the
image handling technology on CMOS sensor.
(B/W : 0.0005 Lux / Color : 0.2Lux@50IRE, F.1.4, 3100K, DSS OFF)
Indoor/Outdoor function
Minimizes the motion blur of object from slowly moving person(Indoor) to fast moving
vehicle(outdoor) by optimizing the signal processing and controls brightness automatically
to perform the best video image
3D-DNR
3D-DNR function efficiently removes video noise in dark environment, and shows clear
image as a result.
True Day & Night function
Camera senses the surrounding brightness automatically, and insert/remove the IR-CUT
filter to get the best sensitivity performance.
WDR/BLC/ACE/HLC
This is a light adjustment feature which can balance image brightness against images with
high contrasts of light.
DEFOG Function
Provides clear and undistorted images from fog, dust, sea fog and any bad weather
conditions.
Adjust Focusing function
Even though D&N lens is in use, focus might be distorted in night time. To prevent this
problem, camera supports Adjust Focusing function. After use this function, you can get
clear video image both daytime and night time.
Privacy support
Camera can support up to 15 privacy masking areas.
3
Supplied accessories
Please check if all the supplied accessories are included.
C1080PBM Install and User’s Manual
C Mount Adapter Camera Remote Controller
Product description
Camera installation
Mount Lens
1. Remove C mount adaptor ring to use CS mount lens.
- Connect C mount adaptor ring to use C mount lens.
2. You may need to loosen the lens locking ring and its adjustment when you cannot get
the focus.
※ Please pay special attention to the bottom of lens not to touch with the surface of
CMOS sensor.
No Name
1 RS-232/RS-485/Digital Output port
2 Power input port
3 RS485 Termination
4 Video Out(PoC,CoC)
5 Menu, CVBS Output
6 Power lamp
4
Auto Iris connector wiring
In case of using Auto Iris lens, connect the Iris Jack of lens to the Iris connector of camera.
1 Damping 2 Damping +
3 Drive +
4 Drive -
How to Set up Install C1080PBM
1. How to connect it with the WEBGATE PoC DVR
- Does not need any additional power adapter. Just connect coaxial cable higher than
4C-HFBT to the DVR.
2. How to connect it with the conventional DVR
- Connect the PoC repeater, RP101P, between the camera and DVR. And put additional
power adopter.
How to use OSD remote controller
1. CVBS output
- Connect CCTV monitor to OSD remote controller’s CVBS outport to check the image.
(SD quality)
- When images stop coming out, press any button on the OSD remote controller to see
the image again.
2. OSD Control
- Press OSD remote controller to control camera’s OSD menu after connected.
Caution in BNC connector connection
The impedance of BNC connector should be 75Ω.
If 50Ω connector is used, the transmission distance will be reduced approx. 10m
Caution in cable selection
The maximum transmission distance of HD-SDI will vary depending on cable manufacturer
and installation environment. Please refer to the below table to select suitable coaxial cable.
5
Caution when Connecting Power
If the DVR does not support PoC function, then the power
must be provided separately. DC12V is required.
When the user uses different power, the camera can seriously
be damaged.
How to upgrade F/W by using CoC(RS485)
1. Connect WEBGATE DVR with camera.
2. Run [HD-SDI Camera Network Upgrader] and select [CoC] on [Serial Port].
- PC and DVR must be connected through network.
3. Select the desired camera’s channel, then write down that DVR’s IP address.
- HD camera upgrade program and F/W can be downloaded from the website.
(http://www.webgateinc.com/)
4. Insert DVR’s Port, User ID, Password and press “Connect” to log-in to the DVR.
5. Select [ON] in Camera OSD Control, then press E,L,R,U,D buttons to check camera’s
OSD control.
- When OSD control is not available, check DVR and camera’s configuration.
6. Select the F/W and press “Load” to upgrade the camera. The camera will reboot.
- Images will be stopped until the boot is complete.
7. When the upgrade is finished, the DVR and CMS (Control CenteR) can be used to
remotely change the camera’s settings.
Cable Type Distance Details
5C2V
Approx.
90M
Analogue cable
4C-FB(T), 4C-HFB(T), RG59
Approx.
140M
High-expansion foam cable,recommends
double(or triple) shielded cable
5C-FB(T), 5C-HFB(T), L-6CHD, RG6
Approx.
180M
Customized HD-SDI cable
6
<Note>
1) When upgrading F/W, the setting will be reset.
How to use OSD menu
OSD menu function
Press [SET] on the OSD remote controller to show OSD configuration menu.
- If OSD menu is not closed, it will be closed automatically in 1 minute.
(Changed configuration value will not be saved)
- Bold font with underline means factory default.
OSD MENU Function
FOCUS ADJ This mode is only enabled in manual lens model. This function prevents
out-focus during day/night.
LENS DC : Auto iris lens mode
MANUAL : Manual lens mode
DAY
&
NIGHT
Color Maintains Color(Day) mode regardless brightness.
B&W Maintains B&W(Night) mode regardless brightness.
Auto In accordance with brightness, camera switches Color
mode and B&W mode automatically.
- LUX LEVEL(LOW, MIDDLE, HIGH) : This value is the
standard for Day & Night switching. If high is
selected, camera will turn to Night(B/W) mode at
higher LUX level than MIDDLE or LOW.
- ANTI HUNT(LOW, MIDDLE, HIGH) : This value is the
standard for threshold of Day & Night switching.
Higher setting value will reduce the flickering by IRCUT filter switching caused from misjudgment.
- DELAY TIME(3~30sec) : Judgment period for Day &
Night switching
D-EXPOSURE
/
N-EXPOSURE
BRIGHTNESS
(8, 0~20)
Adjust the brightness of image.
The more High value it has, the more bright image it
shows
SHUTTER
- INDOOR : controls brightness to show the best video
quality at indoor environment.
- OUTDOOR : controls brightness to show the best
video quality at outdoor environment.
- INDOOR-ANTI BLUR : It shows better anti-blur
performance at dark indoor environment, but the
brightness level decrease a little.
7
- OUTDOOR-ANTI BLUR : It shows better anti-blur
performance at dark outdoor environment, but the
brightness level decrease a little.
- MANUAL : It fixes shutter speed within 1/30 ~
1/60000.
ANTI-FLICKER Removes Flicker problem due to the discordance of
light frequency.
DSS
(AUTO,
OFF,
x2~x10)
During night or low light environment, incrase the
scale factors to maintainet the clear image. However,
larger scales will have motion blurring effect on
moving objects. In AUTO mode, DSS is ON when there
are no motion detection. And when the camera detects
a movement, DSS mode is automatically turned off for
better quality.
AGC
(4, 1~10)
It will amplify video gain according to the light
condition, but it will also increase noise level.
COLOR AWB - AUTO : This mode automatically adjusts color white
balance between 1,700°K ~ 11,000°K.
- PRESET : Shoot a white paper in front of camera and
press MENU button then white balance working will
stop suitable for the condition. You must do this
process again if light condition is changed.
- MANUAL : User can select color temperature among
3300°K, 4300°K, 7600°K and adjust the details by
KELVIN, R-GAIN and B-GAIN value.
CHROMA
(10, 0~20)
Adjust Chroma level.
IMAGE SHARPNESS
(5, 0~10)
Adjust sharpness. The higher value will show more
clear video image
H-MIRROR Mirror image. Left and right will be reversed.
V-MIRROR Flip image. Up and down will be reversed.
Digital ZOOM Zoom image by 16 steps. (1~16)
PRIVACY This is for privacy zone masking
- ZONE NO : Supports total 15 areas (1~15)
- ZONE OP : Whether to use or not of selected area
- X, Y-POS : Set the X,Y start position of an area
- X, Y-SIZE : Set the width and height of an area
- COLOR(WHT,YEL,CYN,GRN,MAG,RED,BLU,BLK) : Select
color for masking.
- TRANS(0~4) : Set transparency of masking.
SHADING Before execute the SHADING function, shoot a white
8
DET paper in front of the camera, and do SHADING DET. If
not, abnormal video might be output.
SHADING It compensates the difference of light caused by lens.
To use this function, you should run Shading DET
function first at System menu.
DEFOG Images can be corrected on Fog, Dust environment.
- AUTO : Automatically corrects the images.
- MANUAL : can be set to LOW, MIDDLE, HIGH.
COLOR BAR Output Color bar for test purpose (2 types).
If there is no user action, it shows for about 1 minute.
WDR This 3D backlight compensation function allows bright and dark area to
be seen clearly together.
- WDR WGT(0~4) : Select image mix ratio. The higher value, the bright
part of the image appear more clearly.
BLC Back light compensation function.
- BLC LEVEL(LOW, MIDDLE, HIGH) : Set BLC level.
- BLC OSD : Displays BLC area on the screen.
- BLC POS-X, Y : Set X, Y start position.
- BLC SIZ-X,Y : Set Width and Height size.
- MASK : If there is very bright portion inside BLC area, this portion can
be removed from the calculation of BLC compensation. This brightness
level for masking can be decided by below MASK LEVEL.
- MASK LEVEL(0~10) : Set brightness level for Masking.
HLC High Light Compensation. If there is very bright portion inside a scene,
camera can mask the portion, and the portion is removed from the
calculation for exposure control.
- LEVEL(5, 0~10) : Set the brightness level for masking.
- Color : Set masking color
ACE
(ON, OFF)
Adaptive Contrast Enhancement. Enhances image quality by raising the
brightness of dark areas.
DNR
(LOW, MIDDLE, HIGH)
Reduce image noise under low light condition
FRAMERATE
(25Hz, 30Hz)
Power frequency 60Hz(NTSC) : 30Hz(fps) video out
Power frequency 50Hz(PAL) : 25Hz(fps) video out
SYSTEM MODEL Displays model name
CAM ID Max. 8 digits for camera name.
Supports alphanumeric and some special characters
RS485 ID Set ID for RS485
VERSION Displays firmware version
VIDEO Full-Scale(BT 709), Comp-Scale(BT 601) support
RESOLUTION Displays video output resolution(1080p/720p)
9
DIGITAL OUT Provides control signal for external illuminator which is
synchronized with image process.
- DURATION(0~20) : Set the one cycle duration of TTL
signal output (unit : msec)
- POLARITY : Set the output level of TTL signal.
(0 : 0V , 1 : 3.3V)
* Output cycle is decided by 30Hz/25Hz.
BOARDRATE
(9600, 57600)
Set RS485 communication speed.
RESET Make all configurations as factory default.
EXIT SAVE&EXIT Save configuration and exit menu.
EXIT Without saving configuration, exit menu.
If there is no further action in menu, after 1 minute,
OSD menu will exit without saving changes.
Product Specification
Model C1080PBM
Video
Sensor Type 1/3”, 2.1Megapixel CMOS
Total Pixels 1920(H) x 1080(V) = 2.1M pixels
Scanning System Progressive Scan
Min
Illumination
B/W 0.0005Lux@50IRE, F1.2, 3100K, DSS(OFF), AGC(10)
Color 0.2Lux@50IRE, F1.2, 3100K, DSS(OFF), AGC(10)
Lens
Mount CS/ C(Ring Adaptor)
Type DC Auto Iris, Manual
Video
Output
Output 1(BNC 1.0 Vp-p, 75Ω)
Resolution 1080p 30fps / 25fps, 720p 25fps / 30fps
HD-SDI SMPTE 292M compatible
Distance approx. 180m of RG6, 140m of RG59
Video
Control
Control Method DVR, CMS(Control Center),Remocon(5Push Bottons)
Filter True Day & Night
AGC 1 ~ 10 steps
Mirror Horizontal / Vertical
WDR OFF, 0 ~ 4 setup
BLC OFF, LOW, MIDDLE, HIGH
ACE OFF, ON
DNR OFF, LOW, MIDDLE, HIGH
DSS AUTO, OFF, x2 ~ x10
White Balance AUTO, PRESET, MANUAL
Defog OFF, AUTO, MANUAL
10
Electric Shutter
INDOOR, OUTDOOR, INDOOR-ANTI BLUR,
OUTDOOR-ANTI BLUR, MANUAL(12 steps),
ANTI-FLICKER
Digital Zoom 0 ~ 16 steps
Lens Shading OFF, ON
HLC 0 ~ 10 steps
Privacy OFF/ON (15 Zones )
Control Interface
CoC / RS485 Upgrade Firmware / OSD Control
Strobe for external light TTL level(3.3v)
Camera Control Remocon
OSD Control / 5Push Bottons
CVBS(NTSC/PAL-Auto change)
Electricity
Power Consumption DC 12V ± 10%, 2W or PoC(DC 24V ± 10%), 3W
Mechanical
Dimension C1080PBM 68(W) x 81(D) x 56(H) mm
Weight C1080PBM 320g (Lens not include)
Environments
Operation Temp. / Humidity -10 ºC ~ 50 ºC / 0%RH ~ 80%RH
Certifications
Certifications KC, FCC, CE, RoHS, HDcctv
Dimension (unit : mm)
C1080PBM
11
Warranty
Product name HD-SDI Camera Warranty term
Model name C1080PBM
2 years after purchase
Date of purchase 20 - -
Warranty term 20 - -
Serial number
Customer’s address
Name
Contact
Address of shop(Company name)
Name
Contact
◈ Please fill out vacant area before sending products.
★ For customer service ★
Please read this manual again before requesting customer service.
Any simple malfunctions due to customer’s misunderstanding on the product could be
resolved by customer.
How to request service?
Please inform details of malfunctions correctly.
Free or non free repair will be decided based on details of warranty card.
WebGate Division Daemyung Enterprise Co., Ltd.
6F Hanlim Venture Town B/D 689-6, Geumjeong Dong, Gunposi, Gyeonggido,Korea
Main : TEL : +82-31-428-9300
Client Service : TEL : +82-1644-3421
The damages caused from following conditions will be repaired by customer’s cost.
1. Any damage comes from customer’s carelessness
2. When improper power is entered
3. When you repair unit by yourself
4. Any damage comes from natural disaster like lightning, flood, etc.
5. Consumable parts replacement
12
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense. Modifications not expressly
approved by the manufacturer could void the user’s authority to operated
the equipment under FCC rules.
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking on the product, accessories or literature indicates that the
product and its electronic accessories (e.g. charger, headset, USB
cable) should not be disposed of with other household waste at the end
of their working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote
the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased
this product or their local government office, for details of where and how
they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for
disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with
separate battery return systems.)
This marking on the battery, manual or packaging indicates that the
batteries in this product should not be disposed of with other household
waste at the end of their working life. Where marked, the chemical
symbols Hg, Cd or Pb indicate that the battery contains mercury,
cadmium or lead above the reference levels in EC Directive 2006/66. If
batteries are not properly disposed of, these substances can cause harm
to human health or the environment.
To protect natural resources and to promote material reuse, please
separate batteries from other types of waste and recycle them through
your local, free battery return system.
Loading...