Weber 96811 User Manual

KETTLE ROTISSERIE

INSTRUCTIONS

96811 10/98

Assembly

1. Install Rotisserie Ring

Place the enameled rotisserie ring inside the kettle so
that the tabs rest on the top edge of the kettle.

2. Attach the Motor

Slide the motor onto the Stainless Steel motor bracket.

4. Put the Spit Forks on the Rotisserie Shaft

Slide the forks onto the shaft so that the tines are facing
each other.Screw in the thumb screws to hold the forks
in place.

5. Insert the Rotisserie Shaft in the Motor

Insert the pointed end of the rotisserie shaft into
the motor.

Retaining loop

Handle of shaft

Travel

Counterweight

Counterweight
assembly

3. Attach the Counterweight to the Rotisserie Shaft

Unscrew the retaining loop, put the counterweight
assembly in place, reattach the retaining loop.

WARNINGS

• Read all instructions before using your rotisserie.

• This rotisserie is for outdoor use only.

• Remove motor and store in a dry place when
not in use.

• Do not touch hot surfaces.Use barbecue mitts.

• This rotisserie is not for use by children.

• To protect against electrical hazards do not immerse
cord, plugs, or motor in water or other liquids.

• Unplug the motor from outlet when not in use, or before
cleaning

• Do not use rotisserie for other than intended use.

• Make sure motor is off before placing it on the
motor bracket.

• Do not operate the rotisserie motor with a damaged
cord or plug.

• Do not operate the rotisserie motor if it
should malfunction.

• The rotisserie motor is equipped with a three prong
(grounding) power cord for your protection against
shock hazard.

• The power cord should be plugged directly into a
properly grounded three prong receptacle. If use of an
extension cord is required, be sure that it is a minimum
16 AWG, 3 wire well insulated cord, marked for
OUTDOOR USE ONLY and properly grounded.

• When using an extension cord, make sure it is not in
contact with hot or sharp surface.

• Outdoor extension cords should be marked with the
letters “W-A” and a tag stating “Suitable for use with
outdoor appliances”.

• Do not cut or remove the grounding prong from the
rotisserie motor power cord.

• Do not let cord hang over any sharp edge or
hot surface.

• Use only outdoors, do not expose to rain.

• To reduce the risk of electric shock, keep extension cord
connection dry and off the ground.

• A short power cord is supplied to reduce the risk of
tripping over the cord.Extension cords may be used, but
caution must be taken to prevent tr ipping over the cord.

SA VE THESE INSTRUCTIONS

IMPORTANT SAFEGUARDS

COOKING

• Meats or poultry should be brought to room
temperature before cooking.(30 to 60 minutes
should be adequate for most foods. If frozen,
defrost completely before cooking.)

• Tie meat or poultry with a string to make the shape
as uniform as possible before putting it on the spit.

• Remove cooking grate to allow food to turn freely.

• Place a drip pan in the center of lower grate before
positioning the rotisserie and food in the barbecue.

• Food preparation steps are the same for
rotisserie cooking.

• Indicated timing in your cookbook will be the same.

• All cooking is done with the lid on.

• Cook by Indirect method as indicated in recipe.

• If foods are too heavy or are irregular shapes, they
may not rotate well and should be cooked by the
indirect cooking method without using the rotisserie.

OPERATING

1. Remove rotisserie shaft from ring. Remove one
spit fork.

2. Prepare the charcoal for Indirect Cooking using a
drip pan.

3. Push the rotisserie shaft through the approximate
center of the food.

4.

Slide the spit fork onto the shaft. Inser t the tines of
both spit forks into the food.

The food should be

centered on the shaft.

Tighten the thumb screws.

5. Set the rotisserie shaft in place in the rotisser ie r ing.
Loosen the retaining loop and let the counterweight
assembly hang down.

6. The rotisserie shaft should rotate so that the heavy
side of the meat or poultry rotates down to the
bottom. Large cuts may require the removal of the
cooking grate to allow full rotation of the shaft.
Remount the food if necessary for better balance.

7. Swing the counterweight assembly so the
counterweight is directly opposite the the heavy side
of the food.The counterweight travel should stick out
a little bit above the shaft handle and retaining loop.
Tighten the retaining loop.

NOTE - Adjust the travel of the counterweight as the
food cooks (shrinks), or if the motor sounds as if it is
straining.

8. Insert the pointed end of the rotisserie shaft into the
motor.Set the rotisserie shaft with food in the
rotisserie ring.

9. Put the cover on the barbecue and turn the rotisserie
motor on.

INSTRUCCIONES PARA EL

ASADOR GIRATORIO

ADVERTENCIAS

• Lea todas las instrucciones antes de utilizar el

asador giratorio.

• Este asador giratorio sólo se debe usar al aire libre.

• Desmonte el motor y guárdelo en un lugar seco

cuando no se use.

• No toque las superficies calientes.Use guantes

para barbacoa.

• Los niños no deben usar este accesorio.

• Desconecte el motor del enchufe cuando no se use.

• No utilice el asador giratorio para otros usos que no

sean los especificados.

• Asegúrese de que el motor esté apagado antes de

colocarlo en el soporte de motor.

• No ponga en marcha el motor del asador giratorio si

hay algún cable o enchufe dañados.

• No ponga en marcha el motor del asador giratorio

cuando funcione defectuosamente.

• No corte ni quite el conductor de puesta a tierra del

cable eléctrico que alimenta al motor del
asador giratorio.

• No deje que el cable cuelgue sobre un borde afilado o

una superficie caliente.

• Como protección contra el peligro de una sacudida

eléctrica, no sumerja en agua, u otros líquidos, el
cable, los enchufes o el motor.

• El motor del asador giratorio está equipado con un

cable eléctrico de tres conductores (con conexión a
tierra) para protección contra las sacudidas eléctricas.

• El cable eléctrico debe conectarse directamente a un

enchufe eléctrico de tres clavijas debidamente
conectado a tierra. Si se requiere el uso de un cable
de extensión, asegúrese de que sea un cable de tres
alambres de 16 AWG, que esté bien aislado, con una
marca de PARA USO AL AIRE LIBRE y debidamente
conectado a tierra.

MONTAJE

1. Instale el anillo del asador giratorio

Coloque el anillo esmaltado del asador giratorio dentro
de la barbacoa, de forma que las lengüetas descansen
sobre el borde superior de la barbacoa.

2. Fije el motor

Deslice el motor sobre el soporte de acero inoxidable
para motor.

4. Coloque los tenedores para asados en el eje del
asador giratorio

Deslice los tenedores sobre el eje de modo que los
dientes estén uno frente al otro.Atornille los tor nillos de
mariposa para fijar los tenedores en su lugar.

5. Inserte el eje del asador giratorio en el motor

Inserte el extremo puntiagudo del eje del asador
giratorio dentro del motor.

Anilla de
retención

Mango del eje

Carrera

Contrapeso Conjunto del

contrapeso

3. Fije el contrapeso del eje del asador giratorio

Desatornille la anilla de retención, ponga el conjunto
del contrapeso en su lugar y vuelva a poner la anilla
de retención.