Guía del Propietario del Asador de Gas Licuado de Propano - Pg. 37
Guide de L’Utilisateur du Grill à Gaz PL - Pg. 73
670
#56206
YOU MUST READ THIS OWNER’S GUIDE
BEFORE OPERATING YOUR GAS GRILL.
m DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open lid.
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death, or damage to property.
m WARNING:
1. Do not store or use gasoline or other
flammable liquids or vapors in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.
m WARNING: Follow all leak-check
procedures carefully in this manual prior
to barbecue operation. Do this even if the
barbecue was dealer-assembled.
NOTICE TO INSTALLER: These instructions
must be left with the owner and the owner
should keep them for future use.
THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.
m WARNING: Do not try to light this
appliance without reading the “MAIN
BURNER IGNITION” section of this
manual.
56206 02/01/10 NG
US - ENGLISH
WARNINGS
m DANGER
Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or
death, or in a fire or an explosion causing damage to property.
m WARNINGS
m Do not store a spare or disconnected liquid propane cylinder under or near this barbecue.
m Improper assembly may be dangerous. Please follow the assembly instructions carefully.
m After a period of storage, and/or nonuse, the Weber® gas barbecue should be checked for gas leaks and burner obstructions
before use. See instructions in this manual for correct procedures.
m Do not operate the Weber® gas barbecue if there is a gas leak present.
m Do not use a flame to check for gas leaks.
m Combustible materials should never be within 24 inches (61 cm) of the back or sides of your Weber
m Do not put a barbecue cover or anything flammable on, or in the storage area under the barbecue.
m Your Weber® gas barbecue should never be used by children. Accessible parts of the barbecue may be very hot. Keep young
children away while it is in use.
m You should exercise reasonable care when operating your Weber
®
gas barbecue. It will be hot during cooking or cleaning and
should never be left unattended, or moved while in operation.
m Should the burners go out while in operation, turn all gas valves off. Open the lid and wait five minutes before attempting to
relight, using the lighting instructions.
m Do not use charcoal or lava rock in your Weber
®
gas barbecue.
m Never lean over open grill or place hands or fingers on the front edge of the cooking box.
m Should a grease fire occur, turn off all burners and leave lid closed until fire is out.
m Do not enlarge valve orifices or burner ports when cleaning the valves or burners.
m The Weber® gas barbecue should be thoroughly cleaned on a regular basis.
m Liquid propane gas is not natural gas. The conversion or attempted use of natural gas in a liquid propane unit or liquid
propane gas in a natural gas unit is dangerous and will void your warranty.
m Do not attempt to disconnect any gas fitting while your barbecue is in operation.
m Use heat-resistant barbecue mitts or gloves when operating barbecue.
m Keep any electrical supply cord and the fuel supply hose away from any heated surfaces.
m Combustion byproducts produced when using this product contain chemicals known to the state of California to cause cancer,
birth defects, or other reproductive harm.
m Do not use this barbecue unless all parts are in place. The unit must be properly assembled according to the assembly
instructions.
m Do not build this model of grill in any built-in or slide in construction. Ignoring this Warning could cause a fire or an explosion
that can damage property and cause serious bodily injury or death.
m Proposition 65 Warning: Handling the brass material on this product exposes you to lead, a chemical known to the state of
California to cause cancer, birth defects or other reproductive harm.
(Wash hands after handling this product.)
LIQUID PROPANE GAS UNITS ONLY:
m Use the pressure regulator and hose assembly that is supplied with your Weber® gas barbecue.
m Do not attempt to disconnect the gas regulator and hose assembly or any gas fitting while your barbecue is in operation.
m A dented or rusty liquid propane cylinder may be hazardous and should be checked by your liquid propane supplier. Do not
use a liquid propane cylinder with a damaged valve.
m Although your liquid propane cylinder may appear to be empty, gas may still be present, and the cylinder should be
transported and stored accordingly.
m If you see, smell or hear the hiss of escaping gas from the liquid propane cylinder:
1. Move away from liquid propane cylinder.
2. Do not attempt to correct the problem yourself.
Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber®
gas grill that it will be free of defects in material and workmanship from the date of purchase as follows:
Aluminum castings, 25-years (2 years on paint; excludes fading)
Stainless steel shroud, 25-years
Porcelain-enameled shroud, 25-years
Stainless steel burners tubes, 10-years
Stainless steel cooking grates, 5-years no rust through or burn through
Stainless steel Flavorizer® bars, 5-years no rust through or burn through
Porcelain-enameled cast-iron cooking grates, 5-year no rust through or burn through
Porcelain-enameled cooking grates, 3-years no rust through or burn through
Porcelain-enameled Flavorizer® bars, 2-years no rust through or burn through
Infrared rotisserie burner, 2-years
All remaining parts, 2-years
when assembled and operated in accordance with the printed instructions accompanying it. Weber
may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR
SALES SLIP OR INVOICE.
This Limited Warranty shall be limited to the repair or replacement of parts that prove defective under
normal use and service and which on examination shall indicate, to Weber’s satisfaction, they are
defective. Before returning any parts, contact the Customer Service Representative in your area
using the contact information on our website. If Weber confirms the defect and approves the claim,
Weber will elect to replace such parts without charge. If you are required to return defective parts,
transportation charges must be prepaid. Weber will return parts to the purchaser, freight or postage
prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse,
misuse, alteration, misapplication, vandalism, improper installation or improper maintenance or
service, or failure to perform normal and routine maintenance, including but not limited to damage
caused by insects within the burner tubes, as set out in this owner’s manual.
Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes
or tornadoes, discoloration due to exposure to chemicals either directly or in the atmosphere, is not
covered by this Limited Warranty.
There are no other express warrants except as set forth herein and any applicable implied warranties
of merchantability and fitness are limited in duration to the period of coverage of this express written
Limited Warranty. Some regions do not allow limitation on how long an implied warranty lasts, so this
limitation may not apply to you.
Weber is not liable for any special, indirect or consequential damages. Some regions do not allow the
exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not
apply to you.
Weber does not authorize any person or company to assume for it any other obligation or liability in
connection with the sale, installation, use, removal, return, or replacement of its equipment; and no
such representations are binding on Weber.
This Warranty applies only to products sold at retail.
WEBER-STEPHEN PRODUCTS CO.
Customer Service Center
1890 Roselle Road, Suite 308
Schaumburg, IL 60195
USA
For replacement parts call:
1-800-446-1071
®
Visit www.weber.com
, select your country of origin, and register your grill today.
6
GENERAL INSTRUcTIoNS
Your Weber® gas barbecue is a portable outdoor cooking appliance. With the Weber®
gas barbecue you can grill, barbecue, roast and bake with results that are difficult to
duplicate with indoor kitchen appliances. The closed lid and Flavorizer
that “outdoor” flavor in the food.
®
The Weber
or on your patio. Portability means you can take your Weber
you move.
The natural gas supply is easy to use and gives you more cooking control than charcoal
fuel.
gas barbecue is portable so you can easily change its location in your yard
®
gas barbecue. Please read the instructions carefully before using your
Weber
Weber® gas barbecue. Improper assembly can be dangerous.
them. Installation must conform with local codes or, in the absence of local codes,
with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and
Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code,
B149.2, or the Standard for Recreational Vehicles, ANSI A 119.2/NFPA 1192, and
CSA Z240 RV Series, Recreational Vehicle Code, as applicable.
liquid propane (LP) bottled gas. The valves, orifices and hose are for natural gas only.
that might obstruct the flow of combustion or ventilation air.
®
CANADIAN INSTALLATION
These instructions, while generally acceptable, do not necessarily comply with the
Canadian Installation codes, particularly with piping above and below ground. In Canada
the installation of this appliance must comply with local codes and/or Standards CAN/
CGA-B149.1 (Installation Code for Natural Gas Burning Appliances and Equipment).
STORAGE
• ThegasmustbeturnedoffatthenaturalgassupplywhentheWeber® gas barbecue
is not in use.
• WhentheWeber
disconnected.
• TheWeber
in the burner tubes before using. (See Section: “MAINTENANCE/ANNUAL
MAINTENANCE”).
gas barbecue is stored indoors, the gas supply must be
®
gas barbecue should be checked for gas leaks and any obstructions
◆
OPERATING
m WARNING: Only use this barbecue outdoors in a well-
ventilated area. Do not use in a garage, building, breezeway
or any other enclosed area.
m WARNING: Your Weber
®
gas barbecue shall not be used
under overhead combustible construction.
m WARNING: Your Weber® gas barbecue is not intended to be
installed in or on recreational vehicles and/or boats.
m WARNING: Do not use the barbecue within 24 inches of
combustible materials. This includes the top, bottom, back
or sides of the grill.
m WARNING: The entire cooking box gets hot when in use. Do
not leave unattended.
m WARNING: Keep any electrical supply cord and the fuel
supply hose away from any heated surface.
m WARNING: Keep the cooking area clear of flammable vapors
and liquids, such as gasoline, alcohol, etc., and combustible
materials.
◆
GAS SUPPLY TESTING
• DisconnectyourWeber® gas barbecue when the gas supply is being tested at high
pressures. This appliance and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of that system at test
pressures in excess of 1/2 psig (3.5 kPa).
• TurnoffyourWeber® gas barbecue when the gas supply is being tested at low
pressures. This appliance must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure testing of the gas
supply piping system at the pressure equal to or less than 1/2 psig (3.5 kPa).
®
bars produce
gas barbecue with you if
◆
◆
◆
WWW.WEbER.com
®
7
GAS INSTRUcTIoNS
INSTALL GAS SUPPLY
General Specifications for Piping
Note: Contact your local municipality for building codes regulating outdoor
gas barbecue installations. In absence of Local Codes, you must conform to
the latest edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas and Propane Installation Code. WE RECOMMEND THAT THIS
INSTALLATION BE DONE BY A PROFESSIONAL.
Some of the following are general requirements taken from the latest edition of the
National Fuel Gas Code: ANSI Z 223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas and
Propane Installation Code for complete specifications.
All connections and joints must be thoroughly tested for leaks in accordance with local
codes and all listed procedures in the latest edition of the National Fuel Gas Code: ANSI
Z 223.1/NFPA 54, or CAN/CGA-B149.1
This is a typical installation of a Weber® natural gas barbecue.
Local codes may require different installations.
INSIDE WALL
1Gas Supply2Shut off
oUTSIDE WALL
3Quick-Disconnect4½"PipeNipple
5Locking Shut Off6Do Not Use
m DANGER
Do not use an open flame to check for gas leaks. Be sure
there are no sparks or open flames in the area while you
check for gas leaks. This will result in a fire or explosion
which can cause serious bodily injury or death and damage
to property.
◆
8
GAS INSTRUcTIoNS
TYPE OF GAS
Your natural gas grill is factory built to operate using natural gas only. Never attempt to
operate your grill on gases other than the type specified on the grill rating plates.
necessary, factory specified parts are required. See your local dealer.
®
For safety and design reasons, the conversion of a Weber
Natural gas to operation using LP gas requires the change out of the entire gas
supply system of the grill. If this becomes necessary, see your dealer for additional
information.
◆
WHAT IS NATURAL GAS?
Natural gas, often called methane, is a safe modern fuel. Natural gas is supplied by your
local utility and should be readily available if your house is already heated with gas.
PORTABLE INSTALLATION
Weber® recommends moving the grill at least two feet from the gas supply and any
combustible surfaces. After the gas supply has been run and checked for leaks in
accordance to the assembly instructions, you are ready to grill. To connect the hose
to the gas supply, pull back the outer fitting, insert the hose fitting all of the way, and
release the outer fitting. This process will produce a gas joint.
grill from operation using
◆
◆
1Swivel Connection
2Install covers when hose is disconnected
3Shut Off Valve
4Coat this pipe nipple with gas resistant pipe dope
5Socket
6Male Connection
1Socket
2Sleeve
3Push Sleeve Back
4Plug
Push plug until sleeve snaps forward locking plug in socket.
(This turns on gas automatically.)
When properly assembled the plug cannot
be removed without pushing the sleeve back.
To disconnect, push sleeve back and pull out plug.
(This automatically shuts off gas.)
WWW.WEbER.com
®
9
GAS INSTRUcTIoNS
LEAK CHECK PREPARATION
Check That All Burner Valves Are Off
Valves are shipped in the OFF position, but you should check to be sure that they are
turned off. Check by pushing in and turning clockwise. If they do not turn, they are off. If
they do turn continue turning them clockwise until they stop, then they are off.
m WARNING: The gas connections of your Summit® gas grill
have been factory tested. We do however recommend that
you leak check all gas connections before operating your
Summit
Remove Control Panel
Parts required: Phillips screwdriver and a towel.
A) Remove the burner control knobs (1).
B) Open both doors and place a towel on top of the doors. This will protect the control
panel and tops of the doors from getting scratched on the next step.
C) Remove the screws from the underside of the control panel with a Phillips
screwdriver (2).
D) Tilt the conrol panel forward and lift up and away from the grill (3) (For Summit®
models with LED features: Be careful not to break or disconnect the wires for the
control panel LED’s).
E) Place the control panel on the towel covering the door assemblies (4).
®
gas grill.
◆
1
The grill illustrated
may have slight
differences than the
model purchased.
2
3
4
10
1
2
GAS INSTRUcTIoNS
CHECK THE FLEXIBLE HOSE TO MANIFOLD CONNECTION
The natural gas hose was attached during the manuafacturing process. We do
recommend that the hose to gas manifold connnection be leak tested, following
guidelines in this Owner’s Guide, prior to barbecue operation.
CHECK FOR GAS LEAKS
m DANGER
Do not use an open flame to check for gas leaks. Be sure
there are no sparks or open flames in the area while you
check for leaks. Sparks or open flames will result in a fire
or explosion which can cause serious bodily injury or death
and damage to property.
Note: All factory-made connections have been thoroughly checked for gas leaks. The
burners have been flame-tested. As a safety precaution however, you should recheck all
fittings for leaks before using your Weber® gas barbecue. Shipping and handling may
loosen or damage a gas fitting.
m WARNING: The gas connections of your gas grill have been
factory tested. We do however recommend that you leak
check all gas connections before operating your gas grill.
m WARNING: Perform these leak checks even if your barbecue
was dealer or store assembled.
If your grill has a side burner make sure the side burner is off.
To perform leak checks: Slide back the collar of the quick disconnect (1). Push male
fitting of the hose into the quick disconnect, and maintain pressure. Slide the collar
closed (2). If it does not engage or lock, repeat procedure. Gas will not flow unless the
quick disconnect is properly engaged. Turn on gas supply.
m WARNING: Do not ignite burners when leak checking.
You will need: A soap and water solution and a rag or brush to apply it.
A) Mix soap and water.
B) Turn on the gas supply.
C) Check for leaks by wetting the fitting with the soap and water solution and watching
for bubbles. If bubbles form, or if a bubble grows, there is a leak.
If there is a leak, turn off the gas and tighten the fitting. Turn the gas back on and
recheck with the soap and water solution.
If leak does not stop do not use the barbecue. Contact the customer service
representative in your area using the contact information on our web site.
Log onto www.weber.com
D) When leak checking is complete, turn gas supply off at the source and rinse
connections with water.
Note: Since some leak test solutions, including soap and water, may be slightly
corrosive, all connections should be rinsed with water after checking for leaks.
®
.
m WARNING: You should check for gas leaks every time you
disconnect and reconnect a gas fitting.
◆
WWW.WEbER.com
®
11
6
3
4
6
7
2
8
9
1
GAS INSTRUcTIoNS
Check:
A) Main gas line to manifold connection (1).
B) Rotisserie (I.R. Burner) gas line connection (2).
C) Bulkhead and gas supply hose connection (3).
D) Bulkhead to regulator connection (4).
E) Regulator to hose connection (5).
m WARNING: If there is a leak at connection (1, 2, 3, 4, or 5),
retighten the fitting with a wrench and recheck for leaks with
soap and water solution.
If a leak persists after re-tightening the fitting, turn off the
gas. DO NOT OPERATE THE GRILL. Contact the Customer
Service Representative in your area using the contact
information on our web site. Log onto www.weber.com®.
F) Bulk head to side burner hose connection (6).
G) Side burner hose to quick disconnect connection, side burner valve and orifice
connections (7).
H) Hose to quick disconnect connection (8).
I) Valves to manifold connections (9).
m WARNING: If there is a leak at connections (6, 7, 8, or 9),
turn off the gas. DO NOT OPERATE THE GRILL. Contact
the Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com®.
When leak checks are complete, turn gas supply off at the source and rinse connections
with water.
Reinstall Control Panel
Parts required: control panel, screws and burner control knobs.
A) Hook the top edge of the control panel onto the control panel brackets on either side
of the front of the cooking box.
B) Line up screws with screw holes on both the control panel bracket and the frame.
Tighten screws.
C) Place corresponding control knobs onto the valve stems.
◆
The grill illustrated may
have slight differences than
the model purchased.
12
1
LIGHT FEATURES
WEBER® GRILL OUT™ HANDLE LIGHT
The Weber Grill Out™ Handle Light has a built-in “Tilt Sensor.” With the power button (1)
activated, the light will come on when the grill lid is open. The light will turn off when the
lid is closed. For daytime use, deactivate the sensor by pressing power button (1).
LIGHTED CONTROL KNOBS
Your gas grill comes with control knobs that light up; allowing you to fine tune heat
settings, even in low light conditions.
Requires 3 “D” alkaline batteries. Do not mix old and new batteries or different types
of batteries (standard, alkaline or rechargeable). Battery housing is located inside the
cabinet on the left side.
To operate, activate power button.
◆
◆
bEFoRE USING YoUR GRILL
SLIDE OUT GREASE TRAY AND DISPOSABLE DRIP PAN
Your grill was built with a grease collection system. Check the slide out grease tray and
disposable drip pan for grease build-up each time you use your grill.
Remove excess grease with a plastic spatula; see illustration. When necessary, wash
the grease tray and drip pan with a soap and water solution, then rinse with clean water.
Replace the disposable drip pan as needed.
m WARNING: Check the slide out grease tray and disposable
drip pan for grease build-up before each use. Remove
excess grease to avoid a grease fire. A grease fire can cause
serious bodily injury or damage to property.
m CAUTION: Do not line the slide out grease tray with
aluminum foil.
◆
The grill illustrated may
have slight differences than
the model purchased.
WWW.WEbER.com
®
13
SNAP IGNITIoN oPERATIoN
2
1
3
4
5
m Always open the lid before igniting the burners.
A) Each control knob has its own igniter electrode built in. To create a spark you must
push the control knob in (1) and turn to START/HI (2).
B) This action will generate gas flow and a spark to the burner lighting tube (3). You will
hear a “snap” from the igniter. You will also see a 3 - 5 orange flame coming from the
burner lighting tube at the left side of the burner (4).
C) Continue to hold the burner control knob in for two seconds after the “snap”.
This will allow gas to flow completely down the burner tube (5) and insure ignition.
D) Check that the burner is lit by looking through the cooking grates. You should see
a flame. If burner does not light on first try, push control knob in and turn to OFF.
Repeat lighting procedure a second time.
m WARNING: If the burner still does not light, turn the burner
control knob to OFF and wait 5 minutes to let the gas clear
before you try again or try to light with a match.
◆
14
1
254
3
24
mAIN bURNER IGNITIoN & USAGE
MAIN BURNER IGNITION
Summary lighting instructions are inside the left hand cabinet door.
m DANGER
Failure to open the lid while igniting the barbecue’s burners,
or not waiting five minutes to allow the gas to clear if the
barbecue does not light, may result in an explosive flame-up
which can cause serious bodily injury or death.
Main Burner Snap Ignition
Note: Each control knob snap igniter creates a spark from the igniter electrode to the
burner lighting tube. You generate the energy for the spark by pushing in the control
knob and turning to START/HI. This will ignite each individual burner.
m WARNING: Check hose before each use of barbecue for
nicks, cracking, abrasions or cuts. If the hose is found to
be damaged in any way, do not use the barbecue. Replace
using only Weber® authorized replacement hose. Contact
the Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com®.
A) Open the lid (1).
B) Make sure all burner control knobs are turned to OFF (2). (Push control knob in and
turn clockwise to ensure that it is in the OFF position.)
C) Turn on the gas supply at source (3).
m WARNING: Do not lean over the open barbecue.
D) Push the control knob in and turn to START/HI until you hear the igniter snap,
continue to hold control knob in for two seconds (4). This action will spark the
igniter, the burner lighting tube and then main burner.
E) Check that the burner is lit by looking through the cooking grates (5). You should see
a flame. If burner does not light on first try, push control knob in and turn to OFF.
Repeat lighting procedure a second time.
m WARNING: If the burner still does not light, turn the burner
control knob to OFF and wait five minutes to let the gas
clear before you try again or try to light with a match.
TO EXTINGUISH
Push in and turn each burner control knob clockwise to OFF position. Turn gas supply off
at the source.
◆
◆
OFFSTART/HIMEDIUMLOW
The grill illustrated may have slight
differences than the model purchased.
WWW.WEbER.com
®
15
1
4
52
3
25
mAIN bURNER IGNITIoN & USAGE
MAIN BURNER MANUAL IGNITION
m DANGER
Failure to open the lid while igniting the barbecue’s burners,
or not waiting five minutes to allow the gas to clear if the
barbecue does not light, may result in an explosive flare-up
which can cause serious bodily injury or death.
A) Open the lid (1).
B) Make sure all burner control knobs are turned to OFF (2). (Push each knob in and
turn clockwise to ensure they are in the OFF position.)
C) Turn on the gas supply at source (3).
D) Put match in the match holder and strike match.
m WARNING: Do not lean over open barbecue.
E) Insert match holder and lit match down through cooking grates and Flavorizer® bars
to ignite the selected burner (4).
F) Push the control knob in and turn to START/HI (5).
m WARNING: If the burner does not light, turn burner control
knob to OFF and wait 5 minutes to let the gas clear before
you try again.
TO EXTINGUISH
Push in and turn each burner control knob clockwise to OFF position. Turn gas supply off
at the source.
◆
◆
The grill illustrated may
have slight differences than
the model purchased.
16
GRILLING TIPS & HELPFUL HINTS
ARRÊTÉ
APAGADO
Note: If grill looses heat while cooking refer to the troubleshooting section of this
manual.
m WARNING: Do not move the Weber® gas barbecue when
operating or while barbecue is hot.
You can adjust the individual burners as desired. The control settings (1) are Start/Hi,
Medium, Low, or OFF.
OFFSTART/HIMEDIUMLOW
1
Note: The temperature inside your cooking box for the first few uses, while surfaces
are still very reflective, may be hotter than those shown in your cookbook. Cooking
conditions, such as wind and weather, may require the adjustment of the burner
controls to obtain the correct cooking temperatures.
If burners go out during cooking, turn off all burners and wait 5 minutes before
relighting.
m WARNING: Check the bottom tray and catch pan for grease
build-up before each use. Remove excess grease to avoid a
grease fire in the bottom tray.
Preheating
Your Weber® gas barbecue is an energy-efficient appliance. It operates at an economical
low BTU rate. Preheating the grill before grilling is important. Light your grill according
to the instructions in this Owner’s Manual. To preheat: after lighting turn all burners to
START/HI, close the lid, and heat until the temperature reaches between 500° and 550°
F (260° and 290° C), the recommended broiling temperature. This will take 10 to 15
minutes depending on conditions such as air temperature and wind.
Covered Cooking
All grilling is done with the lid down to provide uniform, evenly circulated heat. With the
lid closed, the gas grill cooks much like a convection oven. The thermometer in the lid
indicates the cooking temperature inside the grill. All preheating and grilling is done with
the lid down. No peeking — heat is lost every time you lift the lid.
Drippings And Grease
The Flavorizer® bars are designed to “smoke” the correct amount of drippings for
flavorful cooking. Excess drippings and grease will accumulate in the catch pan under
the slide out bottom tray. Disposable foil drip pans are available that fit the catch pan.
Flavorizer® System
When meat juices drip from the food onto the specially angled Flavorizer® bars,
they create smoke that gives foods an irresistible barbecued flavor. Thanks to the
unique design of the burners, Flavorizer® bars and the flexible temperature controls,
uncontrolled flare-ups are virtually eliminated, because YOU control the flames. Because
of the special design of the Flavorizer® bars and burners, excess fats are directed
through the funnel-shaped bottom tray into the grease catch pan.
Sear Station®
Your Weber® gas barbecue includes a sear burner for searing thin meats and fish. The
Sear Station® burner has an on or off control setting (2) that works with the two adjacent
main burners. With the sear and adjacent burners you can effectively sear meats while
using other cooking areas for cooking with moderate heat (See “SEAR STATION®
IGNITION & USAGE” section).
pieces of meat. Foods on a crowded cooking grate will require more cooking time
than just a few foods. Foods grilled in containers, such as baked beans, will require
more time if grilled in a deep casserole rather than a shallow baking pan.
area of the cooking grate. Any flames will quickly subside. After flames subside, relight
the grill. NEVER USE WATER TO EXTINGUISH FLAMES ON A GAS GRILL.
The most important thing to know about grilling is which cooking method to use for a
specific food, Direct or Indirect. The difference is simple: place the food directly over the
fire, or arrange the fire on either side of it. Using the right method is the shortest route to
great results—and the best way to ensure doneness safety.
DIRECT COOKING
The Direct Method, similar to broiling, means the food is cooked directly over the heat
source. For even cooking, food should be turned once halfway through the grilling time.
Use the Direct method for foods that take less than 25 minutes to cook: steaks, chops,
kabobs, sausages, vegetables, and more.
Direct cooking is also necessary to sear meats. Searing creates that wonderful crisp,
caramelized texture where the food hits the grate. It also adds great color and flavor to
the entire surface. Steaks, chops, chicken breasts, and larger cuts of meat all benefit
from searing.
To sear meats, place them over Direct High heat for 2 to 5 minutes per side. Smaller
pieces require less searing time. Usually after searing you finish cooking the food at a
lower temperature. You can finish cooking fast-cooking foods by the Direct method; use
the Indirect method for longer-cooking foods.
To set up your gas grill for Direct cooking, preheat the grill with all burners on HI. Place
food on the cooking grate, and then adjust all burners to the temperature noted in the
recipe. Close the lid of the grill and lift it only to turn food or to test for doneness at the
end of the recommended cooking time.
◆
INDIRECT COOKING
The Indirect Method is similar to roasting, but with the added benefits of that grilled
texture, flavor, and appearance you can’t get from an oven. To set up for Indirect cooking,
gas burners are lit on either side of the food but not directly beneath it. Heat rises,
reflects off the lid and inside surfaces of the grill, and circulates to slowly cook the food
evenly on all sides, much like a convection oven, so there’s no need to turn the food.
Use the Indirect method for foods that require 25 minutes or more of grilling time or that
are so delicate that direct exposure to the flame would dry them out or scorch them.
Examples include roasts, ribs, whole chickens, turkeys, and other large cuts of meat, as
well as delicate fish fillets.
To set up your gas grill for Indirect cooking, preheat the grill with all burners on HI. Then
adjust the burners on each side of the food to the temperature noted in the recipe and
turn off the burner(s) directly below the food. For best results, place roasts, poultry,
or large cuts of meat on a roasting rack set inside a disposable heavy-gauge foil pan.
For longer cooking times, add water to the foil pan to keep drippings from burning. The
drippings can be used to make gravies or sauces.
◆
6 bURNER
DIREcT mETHoD
AFood is placed on the area of the cooking grates directly over the lit burners
6 bURNER
INDIREcT mETHoD
BFood is placed on the area of the cooking grates between the lit burners
18
SIDE bURNER IGNITIoN & USAGE
3
1
2
5
2 4
SIDE BURNER IGNITION
m DANGER
Failure to open the lid while igniting the side burner, or not
waiting 5 minutes to allow the gas to clear if the side burner
does not light, may result in an explosive flare-up which can
cause serious bodily injury or death.
OFF
START/HI
m WARNING: Check hose before each use of barbecue for
nicks, cracking, abrasions or cuts. If the hose is found to
be damaged in any way, do not use the barbecue. Replace
using only Weber® authorized replacement hose. Contact
the Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com®.
A) Open the side burner lid (1).
B) Check that the side burner valve is turned off (Push control knob in and turn
clockwise to ensure that it is in the OFF position), turn all burners not being used to
the OFF position (push in and turn clockwise) (2).
C) Turn the gas supply valve on (3).
D) Push down and turn the side burner control valve to HI (4).
E) Press the igniter button several times so it clicks each time until you see a flame (5).
m CAUTION: Side burner flame may be difficult to see on a
bright sunny day.
m WARNING: If the side burner does not light in five seconds:
a) Turn off the side burner control valve, main burners
and gas supply at source.
b) Wait 5 minutes to let the gas clear before you try
again, or try lighting with a match (see “SIDE BURNER
MANUAL IGNITION”).
◆
LOW
The grill illustrated may
have slight differences than
the model purchased.
WWW.WEbER.com
®
19
SIDE bURNER IGNITIoN & USAGE
2
4
1
2 5
3
SIDE BURNER MANUAL IGNITION
m DANGER
Failure to open the lid while igniting the side burner, or not
waiting five minutes to allow the gas to clear if the side
burner does not light, may result in an explosive flare-up that
can cause serious bodily injury or death.
A) Open the side burner lid (1).
B) Check that the side burner valve is turned off (Push control knob in and turn
clockwise to ensure that it is in the OFF position), turn all burners not being used to
the OFF position (push in and turn clockwise) (2).
C) Turn the gas supply valve on (3).
D) Put match in a match holder and strike match.
E) Hold match holder and lit match by either side of the side burner (4).
F) Push down and turn the side burner control valve to HI (5).
m CAUTION: Side burner flame may be difficult to see on a
bright sunny day.
m WARNING: If the side burner does not light in five seconds:
a) Turn off the side burner control valve, main burners
and gas supply at source.
b) Wait five minutes to let the gas clear before you try
◆
again.
The grill illustrated may
have slight differences than
the model purchased.
20
6
75
1
4
2
3
SEAR STATIoN® IGNITIoN & USAGE
26
ARRÊTÉ
APAGADO
SEAR STATION® BURNER IGNITION
Summary lighting instructions are inside the left hand cabinet door.
m DANGER
Failure to open the lid while igniting the barbecue’s burners,
or not waiting five minutes to allow the gas to clear if the
barbecue does not light, may result in an explosive flame-up
which can cause serious bodily injury or death.
The Sear Station® burner has an on or off control setting. To ignite the Sear Station®
burner you must first ignite the two adjacent main burners.
Adjacent Main Burner Snap Ignition
Note: Each main burner control knob snap igniter creates a spark from the igniter
electrode to the burner lighting tube. You generate the energy for the spark by pushing
in the control knob and turning to START/HI. This will ignite each individual burner.
m WARNING: Check hose before each use of barbecue for
nicks, cracking, abrasions or cuts. If the hose is found to
be damaged in any way, do not use the barbecue. Replace
using only Weber® authorized replacement hose. Contact
the Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com®.
A) Open the lid (1).
B) Make sure all burner control knobs are turned off (2). (Push control knob in and turn
clockwise to ensure that it is in the OFF position.)
C) Turn on the gas supply at source (3).
m WARNING: Do not lean over the open barbecue.
D) Ignite each adjacent Sear Station® main burner (4). Push the control knob in and
turn to START/HI until you hear the igniter snap - continue to hold control knob in
for two seconds. This action will spark the igniter, the burner lighting tube and then
main burner.
E) Check that the burner is lit by looking through the cooking grates (5). You should
see a flame. If burner does not light on first try, push control knob in and turn to OFF.
Repeat lighting procedure a second time.
®
Sear Station
F) Turn Sear Station
G) Verify burner ignition by visual inspection of a flame (7).
m WARNING: If ignition does not occur in five seconds, turn
burner control OFF, wait five minutes, and repeat steps F &
G, or see “SEAR STATION® BURNER MANUAL IGNITION”
instructions.
m WARNING: If the burner still does not light, turn the burner
control knob to OFF and wait five minutes to let the gas
clear before you try again or try to light with a match.
Note: See “MAINTENANCE” for burner removal and cleaning
procedure.
TO EXTINGUISH
Push in and turn each burner control knob clockwise to OFF position. Turn gas supply off
at the source.
Burner Lighting: Ignition By An Adjacent Ignited Main Burner
®
burner control knob to the ON position (6).
◆
◆
OFFON
The grill illustrated may have slight
differences than the model purchased.
WWW.WEbER.com
®
21
4
2
1
3
SEAR STATIoN® IGNITIoN & USAGE
1
SEAR STATION® BURNER MANUAL IGNITION
m DANGER
Failure to open the lid while igniting the barbecue’s burners,
or not waiting 5 minutes to allow the gas to clear if the
barbecue does not light, may result in an explosive flare-up
which can cause serious bodily injury or death.
The Sear Station® burner has an on or off control setting. To ignite the Sear Station®
burner you must first ignite the two adjacent main burners.
Adjacent Main Burner Snap Ignition
Note: Each main burner control knob snap igniter creates a spark from the igniter
electrode to the burner lighting tube. You generate the energy for the spark by pushing
in the control knob and turning to START/HI. This will ignite each individual burner.
A) Open the lid (1).
B) Verify each adjacent Sear Station
flame (2).
C) Put match in the match holder and strike match.
m WARNING: Do not lean over open barbecue.
D) Insert match holder and lit match down through cooking grates and Flavorizer® bars
to ignite the Sear Station® burner (3).
E) Push the Sear Station® control knob in and turn to the ON position (4).
m WARNING: If the burner does not light, turn the burner
control knob to OFF and wait 5 minutes to let the gas clear
before you try again.
Note: See “MAINTENANCE” for burner removal and cleaning
procedure.
◆
TO EXTINGUISH
Push in and turn each burner control knob clockwise to OFF position. Turn gas supply off
at the source.
◆
®
main burner is lit by visual inspection of a
The grill illustrated may
have slight differences
than the model purchased.
6 bURNER
USING THE SEAR STATION
Your Weber® gas barbecue includes a sear burner for searing meats such as steak,
poultry parts, fish, and chops).
Searing is a direct grilling technique which browns the surface of the food at a high
temperature. By searing or browning both sides of the meat you will create a more
desirable flavor by caramelizing the food surface. Searing will also enhance appearance
of the meat with sear marks from the cooking grates. This along with the contrast of
textures and flavors can make food more interesting to the palate.
The Sear Station
adjacent main burners. With the sear and adjacent burners you can effectively sear
meats while using other cooking areas for grilling with moderate heat.
Before searing you should turn all of the main burners on HI for 15 minutes to preheat
the grill. Note: Always grill with the lid closed to allow for maximum heat and to avoid
flare ups.
Once the grill is preheated, turn the outer burners off or down to low. Leave the center
two burners on HI and ignite the Sear Station Burner.
Place the meat directly over the Sear Station
1 to 4 minutes, depending on the type of meat and thickness. You may turn the food a
quarter turn to make crossing sear marks (1) before you sear the other side in the same
manner.
Once you are done searing you can finish grilling by moving the meat to a more
moderate heat over the outside burners to achieve the desired doneness.
As you gain experience in using your Sear Station
with different searing times to find results that work best for your taste.
®
burner has an on or off control setting that works with the two
®
®
. You will Sear each side anywhere from
®
, we encourage you to experiment
◆
SEAR mETHoD
Food is placed in the area of intense heat between the lit burners
22
3
2
8
1
6
4
5
7
SmoKER bURNER IGNITIoN & USAGE
46
ARRÊTÉ
APAGADO
SMOKER BURNER IGNITION
m DANGER
Failure to open the lid while igniting the grill, or not waiting
five minutes to allow the gas to clear if the grill does not
light, may result in an explosive flare-up which can cause
serious bodily injury or death.
Smoker Burner Snap Ignition
Note: The control knob snap igniter creates a spark from the igniter electrode to the
burner lighting tube. You generate the energy for the spark by pushing in the control
knob and turning to START/HI. This will ignite the smoker burner.
m WARNING: Check hose before each use of grill for nicks,
cracking, abrasions or cuts. If the hose is found to be
damaged in any way, do not use the grill. Replace using
only Weber® authorized replacement hose. Contact the
Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com®.
A) Open the grill lid (1).
B) Open smoker box lid (2).
C) Fill smoker with water soaked wood chunks or chips (3).
D) Make sure that all burner control knobs not being used are turned to OFF (4). (Push
control knob in and turn clockwise to ensure that it is in the OFF position).
E) Turn on the gas at source (5).
m WARNING: Do not lean over the open grill while lighting.
F) Push the control knob in and turn to START/HI until you hear the igniter snap (6),
continue to hold control knob in for two seconds. This action will spark the igniter,
the burner lighting tube, and then smoker burner.
G) Check that the burner is lit by looking through the cooking grates (7). You should see
a flame. If burner does not light on first try, push control knob in and turn to OFF.
Repeat lighting procedure a second time.
OFFSTART/HILOW
The grill illustrated may
have slight differences than
the model purchased.
m DANGER
If the smoker burner still does not light, turn the burner
control knob to OFF and wait five minutes to let the gas
clear before you try again, or try lighting with a match (see
“SMOKER BURNER MANUAL IGNITION”).
H) Close smoker cover (8) after wood starts to smolder and turn control knob to LOW.
TO EXTINGUISH
Push in and turn each burner control knob clockwise to OFF position. Turn gas supply off
at the source.
◆
◆
WWW.WEbER.com
®
23
4
5
3
1
2
9
8
6
7
SmoKER bURNER IGNITIoN & USAGE
48
SMOKER BURNER MANUAL IGNITION
A) Open the lid (1).
m DANGER
Failure to open the lid while igniting the grill, or not waiting
five minutes to allow the gas to clear if the grill does not
light, may result in an explosive flare-up which can cause
serious bodily injury or death.
B) Open smoker box lid (2).
C) Fill smoker with water soaked wood chunks or chips (3).
D) Make sure that all burner control knobs not being used are turned to OFF (4).
(Push control knob in and turn clockwise to ensure that it is in the OFF position.)
E) Turn on the gas at source (5).
F) Put a match in the match holder and strike the match.
G) Insert match holder and lit match down through cooking grates and Flavorizer
to ignite smoker burner (6).
m WARNING: Do not lean over the open grill while lighting.
H) Push smoker burner control knob in and turn to START/HI (7).
I) Check that the burner is lit by looking down through the cooking grate (8).
m DANGER
If the smoker burner does not light, turn the burner control
knob to OFF and wait five minutes to let the gas clear before
you try again.
®
bars
The grill illustrated may
have slight differences than
the model purchased.
J) Close smoker cover (9) after wood starts to smolder and turn control knob to LOW.
TO EXTINGUISH
Push in and turn each burner control knob clockwise to OFF position. Turn gas supply off
at the source.
◆
◆
24
1
SmoKER bURNER IGNITIoN & USAGE
USING THE SMOKER
The smoker uses presoaked wood chips. For best results with faster cooking foods like
steaks, burgers and chops, etc., we recommend using finer wood chips because they
ignite and create smoke faster. For longer cooking foods such as roasts, chicken and
turkeys, etc., we recommend using larger wood chunks because they ignite slowly and
provide smoke for a longer period of time. As you gain experience in using your smoker,
we encourage you to experiment with different combinations of wood chips and chunks
to find the smoke flavor that best suits your taste.
As a starting point, soak wood chips in water for at least 30 minutes before using. (Wet
wood will produce more smoke flavor.) Place a handful of wood chips or a few larger
chunks in the bottom of the smoker body (1). As you gain experience in smoking,
increase or decrease the amount of wood to suit your taste.
Note: Always grill with the lid closed to allow the smoke to fully penetrate the food. Light
the smoker burner by following the instructions for “SMOKER BURNER IGNITION”. After
wood starts to smolder turn control knob to LOW.
Smoke will start in approximately 10 minutes and last as long as 45 minutes. If you
require more smoke flavor, refill the smoker with wood chips and/or chunks. Keep the lid
of the grill closed while cooking.
Note: After refilling smoker, smoke will take about 10 to 15 minutes to start again. The
smoker may be used to enhance meat, poultry and fish recipes. Cook with the lid down
according to the times indicated in charts or recipes.
m DANGER
Do not use any flammable fluid in the smoker to ignite the
wood. This will cause serious bodily injury.
CLEANING THE SMOKER
Before each use, empty the smoker of ash to allow proper air flow.
Note: Smoking will leave a “smoke” residue on the surface of the smoker. This residue
cannot be removed and will not affect the function of the smoker. To a lesser degree a
“smoke” residue will accumulate on the inside of your gas grill. This residue need not be
removed and will not adversely affect the function of your gas grill.
◆
◆
WWW.WEbER.com
®
25
1
5
3
4
6
2
RoTISSERIE bURNER IGNITIoN & USAGE
35
ARRÊTÉ
APAGADO
ROTISSERIE BURNER IGNITION
Rotisserie Burner Snap Ignition
Note: Each control knob snap igniter creates a spark from the igniter electrode to the
burner lighting tube. You generate the energy for the spark by pushing in the control
knob and turning to START/HI. This will ignite each individual burner.
m ATTENTION: READ BEFORE
LIGHTING ROTISSERIE BURNER
After a period of non-use, before lighting the Rotisserie
Burner, a few seconds must pass for the gas supply line to fill.
When using the snap igniter you will see a flash of flames
moving from left to right across the Rotisserie Burner
surface, the Rotisserie Burner is not lit until the entire
ceramic surface is aflame.
At this point, start a count of 20 seconds before releasing the
Rotisserie Burner control knob.
The Rotisserie Burner surface will glow red once the burner
is fully ignited.
m DANGER
Failure to open the lid while igniting the grill, or not waiting
five minutes to allow the gas to clear if the grill does not
light, may result in an explosive flare-up which can cause
serious bodily injury or death.
OFFSTART/HILOW
The grill illustrated may have slight
differences than the model purchased.
m CAUTION: The Rotisserie Burner flame may be difficult to
see on a bright sunny day.
m WARNING: Check hose before each use of grill for nicks,
cracking, abrasions or cuts. If the hose is found to be
damaged in any way, do not use the grill. Replace using
only a Weber® authorized replacement hose. Contact the
Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com®.
A) Open the lid (1).
B) Remove the warming rack and the cooking grates from the cookbox (2).
C) Make sure all burner control knobs are turned to off (3). (Push control knob in and
turn clockwise to ensure that it is in the OFF position.)
D) Turn on the gas at source (4).
m WARNING: Do not lean over the open grill.
E) Push the control knob in and turn to START/HI (5). This action will spark the igniter
and light the Rotisserie Burner. Continue to use the snap igniter until the Rotisserie
Burner has ignited. Continue to hold the control knob down until twenty seconds
after the burner has ignited. Release the control knob.
F) Check that the burner is lit by looking for the rotisserie burner to glow red (6).
m WARNING: If the rotisserie burner does not light, turn the
burner control knob to OFF and wait five minutes to let the
gas clear before you try again or try to light with a match.
Note: When using the rotisserie with the lid closed, only light two of the main burners
on each side of the food (See “INDIRECT COOKING”). Check your food periodically
to prevent over cooking on the outside. Turn off the rotisserie burner once the food has
browned to the desired color. Finish cooking on indirect heat.
TO EXTINGUISH
Push in and turn each burner control knob clockwise to OFF position. Turn gas supply off
at the source.
◆
26
4
1
3
2
7
5
6
RoTISSERIE bURNER IGNITIoN & USAGE
36
ROTISSERIE BURNER MANUAL IGNITION
m ATTENTION: READ BEFORE
LIGHTING ROTISSERIE BURNER
After a period of non-use, before lighting the Rotisserie
Burner, a few seconds must pass for the gas supply line to
fill. When holding a match to the rotisserie burner you will
see a flash of flames moving from left to right across the
Rotisserie Burner surface, the Rotisserie Burner is not lit
until the entire ceramic surface is aflame. At this point, start
a count of 20 seconds before releasing the Rotisserie Burner
control knob. The Rotisserie Burner surface will glow red
once the burner is fully ignited.
m DANGER
Failure to open the lid while igniting the grill, or not waiting
5 minutes to allow the gas to clear if the grill does not light,
may result in an explosive flare-up which can cause serious
bodily injury or death.
m CAUTION: The Rotisserie Burner flame may be difficult to
see on a sunny day.
m WARNING: Check hose before each use of grill for nicks,
cracking, abrasions or cuts. If the hose is found to be
damaged in any way, do not use the grill. Replace using
only a Weber® authorized replacement hose. Contact the
Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com®.
A) Open the lid (1).
B) Remove the warming rack and the cooking grates from the cookbox (2).
C) Make sure all burner control knobs are turned to off (3). (Push control knob in and
turn clockwise to ensure that it is in the OFF position.)
D) Turn on the gas at source (4).
E) Put a match in the match holder and strike the match.
F) Hold match holder and lit match by right side of rotisserie burner (5).
m WARNING: Do not lean over the open grill.
G) Push rotisserie burner control knob down and turn to START/HI (6). Continue to hold
the control knob down until twenty seconds after the burner has ignited.
H) Check that the burner is lit by looking for the rotisserie burner to glow red (7).
m WARNING: If the rotisserie burner does not light, turn the
burner control knob to OFF and wait five minutes to let the
gas clear before you try again.
Note: When using the rotisserie with the lid closed, only light two of the main burners
under the food (See “INDIRECT COOKING”). Check your food periodically to prevent
over cooking on the outside. Turn off the rotisserie burner once the food has browned to
the desired color. Finish cooking on indirect heat.
TO EXTINGUISH
Push in and turn each burner control knob clockwise to OFF position. Turn gas supply off
at the source.
◆
◆
The grill illustrated may
have slight differences than
the model purchased.
WWW.WEbER.com
®
27
RoTISSERIE bURNER IGNITIoN & USAGE
2
1
4
5
3
BEFORE USING YOUR ROTISSERIE
Note: Before using your rotisserie, measure your food at the widest point. If it exceeds
9½" (241.8mm), it is too large to fit the rotisserie. If it is too large, food can be prepared
using a roast holder and the Indirect Cooking Method.
Important Safeguards
m WARNINGS
m Read all instructions before using your rotisserie.
m This rotisserie is for outdoor use only.
m Remove motor and store in a dry place when not in use.
m Do not touch hot surfaces. Use barbecue mitts.
m This rotisserie is not for use by children.
m To protect against electrical hazards do not immerse cord,
plugs, or motor in water or other liquids.
m Unplug the motor from outlet when not in use or before
cleaning.
m Do not use rotisserie for other than intended use.
m Make sure motor is off before placing it on the motor
bracket.
m Do not operate the rotisserie motor with a damaged cord or
plug.
m Do not operate the rotisserie motor if it should malfunction.
m The rotisserie motor is equipped with a three prong
(grounding) power cord for your protection against shock
hazard.
m The power cord should be plugged directly into a properly
grounded three prong receptacle. If use of an extension
cord is required, be sure that it is a minimum 16 AWG
(1.3mm), 3-wire, well insulated cord marked for OUTDOOR
USE ONLY and properly grounded.
m When using an extension cord, make sure it is not in contact
with a hot or sharp surface.
m Outdoor extension cords should be marked with the letters
“W-A” and a tag stating “Suitable for use with outdoor
appliances”.
m Do not cut or remove the grounding prong from the
rotisserie motor power cord.
m Do not let cord hang over any sharp edge or hot surface.
m To reduce the risk of electric shock, keep extension cord
connection dry and off the ground.
m A short power cord is supplied to reduce the risk of tripping
over the cord. Extension cords may be used, but caution
must be taken to prevent tripping over the cord.
m In absence of local codes the rotisserie motor must be
grounded electrically in accordance with the National
Electric Code, ANSI / NFPA 70, or Canadian Electrical Code,
CSA C22.1.
◆
OPERATING THE ROTISSERIE
m WARNING: Setup up the rotisserie with food before lighting
rotisserie burner.
A) To set up rotisserie motor, push the button on the retractable rotisserie panel (1).
Pull rotisserie panel upwards. Push locking tab (2) until it snaps into place.
B) Remove power cord and plug into power source.
m CAUTION: Do not route rotisserie motor power cord through
the retractable rotisserie opening in the side table.
m CAUTION: Inspect power cord before each use. If cord
is damaged, do not use. Contact the Customer Service
Representative in your area using the contact information
on our web site. Log onto www.weber.com®.
C) Slide one of the spit forks towards the right side of the rotisserie shaft, making sure
that the spikes face to the left and the fork screw faces down (3).
D) Push the rotisserie shaft through the center of the food. Insert the tines of both spit
forks into the food. The food should be centered on the shaft. Tighten the spit fork
screw (4).
E) Slide another spit fork onto the rotisserie shaft, making sure that the spikes face to
the right and the fork screw faces up. Insert the tines of both spit forks into the food.
Tighten the spit fork screw (5).
28
RoTISSERIE bURNER IGNITIoN & USAGE
3
2
1
F) Insert the pointed end of the rotisserie shaft into the motor. Lower the rotisserie spit
into the grooves on the cookbox (6).
G) The rotisserie shaft should rotate so that the heavy side of the meat or poultry
rotates down to the bottom. Large cuts may require the removal of the cooking
grates and warming rack to allow full rotation of the shaft. Remount the food if
necessary for better balance.
H) Turn the motor on.
Note: When using the rotisserie burner, grill thermometer will not reflect the temperature
inside the cooking box.
ROTISSERIE MOTOR STORAGE
A) Before retracting rotisserie back into the side table, unplug the power cord and
carefully place plug/power cord into the storage area of the retractable rotisserie
assembly (1).
m CAUTION: Failure to properly store the rotisserie power
cord may result in damage to the power cord when opening
and closing the retractable rotisserie panel.
B) Using your index finger, disengage retractable rotisserie panel (2). Push panel down
until it snaps securly in place (3).
ROTISSERIE SPIT STORAGE
A) Remove forks from rotisserie spit. Carefully insert spit into cabinet by sliding through
hole in right side panel (1).
m CAUTION: Do not allow rotisserie spit to come into contact
with any gas lines.
B) Store rotisserie forks by placing them on the hooks located on the catch pan holder
within the grill cabinet (2).
◆
◆
◆
◆
6
1
2
3
1
2
WWW.WEbER.com
®
29
TRoUbLESHooTING
PRobLEmcHEcKSoLUTIoN
Burners burn with a yellow or
orange flame, in conjunction with
the smell of gas (This is normal for
the burner lighting tube).
Symptoms:
Burner does not light, or flame is
low in HI position.
Experiencing flare-ups:
m CAUTION: Do not line
the bottom tray with
aluminum foil.
Burner flame pattern is erratic.
Flame is low when burner is on HI.
Flames do not run the whole length
of the burner tube.
Inside of lid appears to be “peeling.”
(Resembles paint peeling.)
Cabinet doors are not aligned.Check the adjustment pin on the bottom of each door.Loosen adjustment nut/s. Slide door/s until aligned. Tighten nut.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com
Inspect Spider/Insect Screens for possible obstructions. (Blockage
of holes.)
Is fuel hose bent or kinked?Straighten fuel hose.
Does Burner light with a match?Clean burners (refer to “MAINTENANCE”).
Did you use the snap igniter several times until the main burner lit
(refer to “MAIN BURNER IGNITION”)?
Does the igniter work? Do you see a spark when you repeatedly
use the snap igniter?
Are you preheating barbecue in the prescribed manner?All burners on HI for 10 to 15 minutes for preheating.
®
Are the cooking grates and Flavorizer
burned-on grease?
Is the bottom tray “dirty” and not allowing grease to flow into catch
pan?
Are burners clean?Clean burners (refer to “MAINTENANCE”).
The lid is porcelain enamel or stainless steel, not paint. It cannot
“peel”. What you are seeing is baked on grease that has turned to
carbon and is flaking off.
THIS IS NOT A DEFECT.
®
.
bars heavily coated with
Clean Spider/Insect Screens (refer to “ANNUAL MAINTENANCE”).
Make sure to hold the control knob in for two seconds after
snapping the igniter and seeing the orange flame from the burner
lighting tube.
Try manually lighting the burner (refer to “MAIN BURNER
MANUAL IGNITION”). Call customer service.
Clean thoroughly (refer to “CLEANING”).
Clean bottom tray.
Clean thoroughly (refer to “CLEANING”).
SIDE bURNER TRoUbLESHooTING
PRobLEmcHEcKSoLUTIoN
Side Burner does not light.Is gas supply off?Turn supply on.
Flame is low in HI positionIs the fuel hose bent or kinked?Straighten hose.
Push button ignition does not work. Does burner light with a match?If match lights burner, check igniter (refer to “SIDE BURNER
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com
®
.
MAINTENANCE”).
30
Loading...
+ 78 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.