Page 1
61273 0204
LP Tank Cabinet Installation and Owner’s Guide
YOU MUST READ THIS OWNER’S GUIDE BEFORE OPERATING YOUR LP TANK DRAWER
Vieluxe®LP Tank Cabinet
(Model #: 36299)
NOTICE TO INSTALLER: These
instructions must be left with the owner
and the owner should keep them for
future use.
WARNING: Follow all leak-check
procedures carefully in this manual
prior to grill operation. Do this even if
grill was dealer-assembled.
WARNING: Do not try to light this
appliance without reading "Lighting"
instructions section of this manual.
THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open lid.
4. If odor continues, keep away from the
appliance and immediately call your
gas supplier or your fire department.
Leaking gas may cause a fire or
explosion which can cause serious bodily
injury or death, or damage to property.
WARNING
1. Do not store spare liquid propane
cylinder within 10 feet (3m) of this
appliance.)
2. Do not store or use gasoline or other
flammable liquids or vapors within
25 feet (8m) of this appliance.
THESE ACCESSORIES MAY BE PURCHASED SEPERATELY.
THIS GAS APPLIANCE IS DESIGNED FOR OUTDOOR USE ONLY.
Page 2
2
DANGER
Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual
may result in serious bodily injury or death, or in a fire or an explosion causing damage
to property.
WARNINGS
Do not store a spare or disconnected liquid propane cylinder under or near this grill.
Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual.
After a period of storage, and/or non use, the Vieluxe®gas grill should be checked for gas leaks and
burner obstructions before use. See instructions in this manual for correct procedures.
Do not operate the Vieluxe®gas grill if there is a gas leak present.
Do not use a flame to check for gas leaks.
Combustible materials should never be within 24 inches of the top, bottom, back or sides of your
Vieluxe
®
gas grill.
Do not put a grill cover or anything flammable on, or in the storage area under the grill.
Your Vieluxe®gas grill should never be used by children. Accessible parts of the grill may be very hot.
Keep young children away while it is in use.
You should exercise reasonable care when operating your Vieluxe®gas grill. It will be hot during cooking
or cleaning and should never be left unattended, or moved while in operation.
Should the burners go out while in operation, turn all gas valves off. Open the lid and wait five minutes
before attempting to relight, using the lighting instructions.
Do not use charcoal or lava rock in your Vieluxe®gas grill.
Never lean over open grill or place hands or fingers on the front edge of the cooking box.
Should a grease fire occur, turn off all burners and leave lid closed until fire is out.
Do not enlarge valve orifices or burner ports when cleaning the valves or burners.
The Vieluxe®gas grill should be thoroughly cleaned on a regular basis.
Liquid propane gas is not natural gas. The conversion or attempted use of natural gas in a liquid
propane unit or liquid propane gas in a natural gas unit is dangerous and will void your warranty.
Do not attempt to disconnect any gas fitting while your grill is in operation.
Use heat-resistant grill mitts or gloves when operating grill.
Combustion by-products produced when using this product contain chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
LIQUID PROPANE GAS UNITS ONLY:
Use the regulator that is supplied with your Vieluxe®gas grill.
Do not attempt to disconnect the gas regulator or any gas fitting while your grill is in operation.
A dented or rusty liquid propane cylinder may be hazardous and should be checked by your liquid
propane supplier. Do not use a liquid propane cylinder with a damaged valve.
Although your liquid propane cylinder may appear to be empty, gas may still be present, and the cylinder
should be transported and stored accordingly.
If you see, smell or hear the hiss of escaping gas from the liquid propane cylinder:
1. Move away from liquid propane cylinder.
2. Do not attempt to correct the problem yourself.
3. Call your fire department.
Page 3
3
Weber-Stephen Products Co. (Weber-Stephen) hereby warrants to the ORIGINAL PURCHASER of this
Vieluxe
®
gas grill that it will be free of defects in material and workmanship from the date of purchase as follows:
When assembled and operated in accordance with the printed instructions accompanying it.
Weber-Stephen may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN
YOUR SALES RECEIPT OR INVOICE.
This Limited Warranty shall be limited to the repair or replacement of parts that prove defective under normal use
and service and which on examination shall indicate, to Weber-Stephen’s satisfaction, they are defective. Before
returning any parts, contact Customer Service Toll Free at 1-866-VIELUXE
SM
. If Weber-Stephen confirms the
defect and approves the claim, Weber-Stephen will elect to replace such parts without charge. If you are required to
return defective parts, transportation charges must be prepaid. Vieluxe
®
will return parts to the purchaser, freight or
postage prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration,
misapplication, vandalism, improper installation or improper maintenance or service, or failure to perform normal and
routine maintenance, including but not limited to damage caused by insects within the burner tubes, as set out in this
owner’s manual.
Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes or tornadoes,
discoloration due to exposure to chemicals either directly or in the atmosphere, is not covered by this Limited
Warranty.
There are no other express warrants except as set forth herein and any applicable implied warranties of
merchantability and fitness are limited in duration to the period of coverage of this express written Limited Warranty.
Some regions do not allow limitation on how long an implied warranty lasts, so this limitation may not apply to you.
Weber-Stephen is not liable for any special, indirect or consequential damages. Some regions do not allow the
exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.
Weber-Stephen does not authorize any person or company to assume for it any other obligation or liability in
connection with the sale, installation, use, removal, return, or replacement of its equipment; and no such
representations are binding on Weber-Stephen.
This Warranty applies only to products sold at retail.
Vieluxe
®
Customer Service
1890 Roselle Road, Suite 308
Schaumburg, IL 60195
USA
www.vieluxe.com
For Replacement Parts or Service Contact Customer Service Toll Free at 1-866-VIELUXESM.
- Tank Cabinet 10 - Years
- All remaining parts 5 - Years
WARRANTY
Page 4
4
GENERAL INSTRUCTIONS
Liquid Propane (LP) gas supply is easy to use and gives you more cooking control than charcoal fuel.
• These instructions will give you the minimum requirements for assembling your Vieluxe
®
grill. Please read the
instructions carefully before using your Vieluxe®grill. Improper assembly can be dangerous.
• Not for use by children.
• If there are local codes that apply to portable gas grills, you will have to conform to them. If there are no local
codes, you must conform to the latest edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA 54.
• The pressure regulator supplied with the Vieluxe
®
grill must be used. This regulator is set for 10.5 inches of water
column (pressure).Replacement parts can be ordered by contacting Customer Service toll free at
1 (866) Vieluxe®.
• This Vieluxe®grill is designed for use with liquid propane (LP) gas only. Do not use with natural (piped in city) gas.
The valves, orifices, hose and regulator are for LP gas only.
• Do not use with charcoal fuel.
• Check that the area under the control panel and the bottom tray are free from debris that might obstruct the flow
of combustion or ventilation air.
• The areas around the LP cylinder must be free and clear from debris.
Storage
• The gas must be turned OFF at the LP cylinder when the Vieluxe®grill is not in use.
• When the Vieluxe®grill is stored indoors, the gas supply must be disconnected and the LP cylinder stored
outdoors, in a well-ventilated space, and.out of the reach of children. Disconnected LP cylinders must not be
stored in a building, garage or any other enclosed area.
• When the LP cylinder is not disconnected from the Vieluxe
®
grill, the appliance and LP cylinder must be kept
outdoors in a well-ventilated space.
Operating
WARNING: Only use this grill outdoors in a well-ventilated area. Do not use in a garage, building,
breezeway or any other enclosed area.
WARNING: Never use your Vieluxe
®
grill under an unprotected combustible roof or overhang.
WARNING:Your Vieluxe
®
grill is not intended to be installed in or on recreational vehicles and/or boats.
WARNING: Do not use combustible materials within 26 inches of the top, bottom, back or sides of
the grill.
WARNING:The entire cooking box gets hot when in use. Do not leave unattended.
WARNING: Keep any electrical supply cord and the fuel supply hose away from any heated surface.
WARNING: Keep the cooking area clear of flammable vapors and liquids such as gasoline, alcohol, etc.,
and combustible materials.
WARNING: Never store an extra (spare) LP cylinder under or near the Vieluxe
®
grill.
WARNING: Keep the ventilation openings of the cylinder enclosure free and clear of debris.
WARNING:Turn off the gas at the LP gas supply cylinder when the outdoor cooking gas appliance is not
in use.
WARNING: Never store an outdoor cooking gas appliance indoors unless the LP cylinder is disconnected
and removed from the outdoor cooking gas appliance.
WARNING: LP Cylinders must be stored outdoors out of the reach of children and must not be stored in a
building, garage, or any other enclosed area.
WARNING:The LP pressure regulator and hose assembly supplied with the outdoor cooking gas
appliance must be used. Replacement LP pressure regulators and hoses must be obtained from
Weber-Stephen Product Co..
Page 5
5
CLEARANCE FROM COMBUSTIBLE
SURFACES OR STRUCTURES
WARNING: Clearance from the outside
walls of the sides and back of the LP Tank
Cabinet must be a minimum of 26 inches
any surface. Refer to “Typical Gas Supply
Installation” before starting installation.
LOCATING YOUR LP TANK CABINET
When determining a suitable location for your LP Tank Cabinet installation, give attention to concerns such as
exposure to wind, proximity to traffic paths, and keeping any gas supply lines as short as possible. Never locate the
Vieluxe
®
LP Tank Cabinet in a garage, breezeway, shed, under an unprotected overhang, or other enclosed area.
Locate the LP Tank Cabinet and structure so there is enough room to safely evacuate the area in case of a fire.
WARNING: The structure, “island”
countertops and adjacent work areas for
the LP Tank Cabinet installation must be
built from non-combustable materials only.
NOTE: If you have questions on what
materials are considered non-combustable,
contact you local building supplier or fire
department.
WARNING: All countertop finished surfaces must be constructed of a noncombustible material.
WARNING: Air holes must be provided in the structure at the top and bottom to provide ventilation in the
event of a gas leak.
Air holes can be located in a low visibility area and should be protected by screening material to prevent rodents and
insects from entering the structure. Air holes will also help dry moisture.
All dimensions are to finished surfaces.
LP Tank
Cabinet Tolerances
A21
1
⁄4"
B 28"
C 20"
+
1
⁄4
- 1⁄4
+ 1⁄4
- 1⁄4
+ 1⁄4
- 1⁄4
DIMENSIONS
BUILT-IN STRUCTURE
CUTOUT DIMENSIONS
Non-Combustible Surface
26 inches
26 inches
LP Tank
Drawer
26 inches
Page 6
6
Area should be kept clear of sharp, jagged, or
extremely abrasive surfaces to avoid possible damage
to gas supply lines. Exercise caution when pulling gas
lines through built-in structure.
LP TANK CABINET
GAS LINE DIMENSIONS
LP Tank
Cabinet Tolerances
A5"
B 2.45"
C 1.75"
0
0
0
DIMENSIONS
BUILT-IN GAS LINE
LOCATIONS
Located inside the door frame of the LP Tank Cabinet,
holes are provided that are intended for mounting your
LP Tank Cabinet to the "island" structure.
MOUNTING THE
LP TANK CABINET
Be sure to mount the LP Tank Cabinet before use.
Front of LP Tank Drawer Structure
Plan View
B
A
C
Front View
B
Side View
A
C
Page 7
7
CONNECT GAS SUPPLY
A 48" inch corrugated gas line is supplied with the grill.
This line needs to pass through the gas inlet opening to
the main gas supply.
1) Uncap one flare fitting from the T Connection
located inside the Vieluxe
®
Tank Cabinet (#36299).
Note: Leave an access in the "island" structure for
gas supply and regulator service, not inside the
grill structure. Weber
®
has a gas line and regulator
access door available from your dealer or call
Vieluxe®Customer Service at 1-866-VIELUXE.
2) Connect the corrugated gas line from the grill to the
T Connecton.
T Connection
Cap
Corrugated Gas Line
to Manifold
Plug unused hole.
Use Bushing for
Gas Line Hole
T Connect
Cap
Corrugated Gas Line
to Manifold
Connection to
LP Tank
The second capped connection is for an optional
accessory side burner.
if the second connection in not used, plug the unused
hole in the LP tank cabinet.
Fill liquid propane cylinder
Note - The liquid propane cylinder manufacturer is
responsible for the materials, workmanship and
performance of the cylinder. If the cylinder has a
defect, malfunctions, or you have a question regarding
the cylinder, call the cylinder manufacturer’s customer
service center. The phone number is on the warning
decal, which is permanently attached to the cylinder. If
the cylinder manufacturer has not resolved the issue to
your satisfaction, then contact the Customer Service
Representative in your region using the contact
information sheet provided with your manual.
To fill, take the liquid propane cylinder and filler
adapter to an RV center or look up gas-propane in the
phone book for other sources of liquid propane gas.
WARNING: We recommend that your liquid
propane cylinder be filled at an authorized
liquid propane gas dealer by a qualified
attendant, who fills the tank by weight.
IMPROPER FILLING IS DANGEROUS.
Tell your liquid propane dealer that this is a new liquid
propane cylinder. The air must be removed from a new
liquid propane cylinder before the initial filling. Your
liquid propane cylinder dealer is equipped to do this.
The liquid propane cylinder must be installed,
transported and stored in an upright position, and
should not be dropped or handled roughly.
Never store or transport the liquid propane cylinder
where temperatures can reach 125° Fahrenheit (too
hot to hold by hand – for example: do not leave the
liquid propane cylinder in a car on a hot day).
For full instructions on safe handling of liquid propane
cylinders, see Section “Operating”.
GAS INSTRUCTIONS
Page 8
8
Important LP Cylinder Information
Failure to follow these DANGER statements exactly
may result in a fire causing death or serious injury.
DANGER
NEVER store a spare LP Cylinder under or near
this grill.
NEVER fill the tank beyond 80% full.
Your Weber
®
gas grill is equipped with a cylinder
supply system designed for vapor withdrawal.
WARNING: Only use this grill outdoors in a well-
ventilated area. Do not use in a garage, building,
breezeway or any other enclosed area.
The LP cylinder supplied with your barbecue is
equipped with an OPD (Overfilling Prevention
Device) and a QCC1 or Type 1 (CGA810) cylinder
connection. The cylinder connection is compatible
with the grill connection.
This is a secondary device to prevent the overfilling of
your LP cylinder. The proper filling methods for the
filling of your cylinder are by weight or volume, as
described in NFPA 58. Please make sure your filling
station fills your LP cylinder by weight or volume. Ask
your filling station to read purging and filling
instructions on the LP cylinder before attempting to fill.
WARNING: Do not exchange the LP tank
provided with your barbecue, unless the
exchange LP tank is equipped with an OPD.
Otherwise you will lose the OPD (Overfilling
Prevention Device) feature. If there is not an LP
tank available for exchange equipped with an
OPD, we recommend that you have your LP
tank filled at an authorized LP gas dealer by a
qualified attendant.
Check that all burner valves are off
Valves are shipped in the OFF position, but you should
check to be sure that they are turned OFF. Check by
pushing down and turning clockwise. If they do not
turn, they are off. Proceed to the next step. If they do
turn continue turning them clockwise until they stop,
then they are off. Proceed to the next step.
Connecting the Liquid Propane Cylinder
WARNING: Make sure that the LP cylinder valve
is closed. Close by turning valve clockwise.
DANGER
Do not use an open flame to check for gas leaks.
Be sure there are no sparks or open flames in the
area while you check for leaks. Sparks or flames
will result in a fire or explosion which can cause
serious bodily injury or death, and damage to
property.
Raises up while filling
then stops when full.
Page 9
9
We utilize various LP tank manufacturers. Some of the
tanks have differing top collar assembles. (The top
collar is the metal protective ring around the valve.)
One series of tanks mount with the valve facing front.
The other tanks mount with the valve facing away from
the fuel scale. These types of tanks are illustrated
below.
You will need: LP cylinder, a soap and water solution
and a rag or brush to apply it.
1) Turn the LP cylinder so the opening of the valve is
either to the front, side or rear of the Vieluxe
®
LP
Tank Drawer. Lift and hook the cylinder onto the
fuel gauge.
2) Loosen the cylinder lock wing nut. Swing the
cylinder lock down. Tighten the wing nut.
To Connect the hose to the cylinder.
3) Remove the plastic dust cover from the valve.
4) Screw the regulator coupling onto the tank valve,
clockwise, or to the right. Hand-tighten only.
Note: This is a new type of connection. It tightens
clockwise and will not allow gas to flow unless the
connection is tight. The connection requires tightening
by hand only.
WARNING: Do not use a wrench to tighten the
connection. Using a wrench could damage the
regulator coupling and could cause a leak.
5) Mix soap and water.
6) Turn on the cylinder valve.
7) Check for leaks by wetting the fitting with the soap
and water solution and watching for bubbles. If
bubbles form, or if a bubble grows, there is a leak.
If there is a leak, turn off the gas and tighten the fitting.
Turn the gas back on and recheck with the soap and
water solution.
If leak does not stop, Contact information sheet
provided with your manual. Do not use the barbecue.
8) When leak checking is complete, turn gas supply
OFF at the source and rinse connections with water.
Page 10
10
Check for gas leaks
After a period of nonuse, we recommend that you
perform the following maintenance procedures for your
safety.
WARNING: Check the hose before each use of
the grill for nicks, cracking, abrasions or
cuts. If the hose is found to be damaged in any
way, do not use the grill. Replace using
only Vieluxe
®
authorized replacement hose.
Contact the Vieluxe®Customer Service at
1-866-VIELUXE.
■ Inspect the burners for correct flame pattern. Clean
if necessary, following the procedures outlined in
the “General Maintenance” section of this manual.
■ Check all gas fittings for leaks.
DANGER
Do not use an open flame to check for gas leaks.
Be sure there are no sparks or open flames in the
area while you check for leaks. Sparks or flames
will result in a fire or explosion, which can cause
serious bodily injury or death, and damage
to property.
WARNING:You should check for gas leaks every
time you disconnect and reconnect a gas fitting.
Note - All factory-made connections have been
thoroughly checked for gas leaks. The burners have
been flame tested. As a safety precaution however,
you should recheck all fittings for leaks before using
your Vieluxe
®
gas grill. Shipping and handling may
have loosened or damaged a gas fitting.
WARNING: Perform these leak checks even if
your grill was professionally installed.
You will need: a soap and water solution and a rag or
brush to apply it.
To perform leak checks: Make sure all Burners are in
the off position. Turn on gas supply.
WARNING: Do not ignite burners while leak
checking.
Check for leaks by wetting the connections with the
soap and water solution and watching for bubbles. If
bubbles form, or if a bubble grows, there is a leak.
Note - Since some leak test solutions, including soap
and water, may be slightly corrosive, all connections
should be rinsed with water after checking for leaks.
Check:
1) Gas Line-to-"T" Connection.
2) Regulator-to-Cylinder connection.
WARNING: If there is a leak at connection (1),
retighten the fitting with a wrench and recheck
for leaks with soap and water solution.
If a leak persists after retightening the fitting, turn
OFF the gas. DO NOT OPERATE THE GRILL.
Contact the Vieluxe
®
Customer Service at
1-866-VIELUXE.
Check:
3) "T" Connection-to-Hose connections.
4) The hose-to-Regulator connection.
WARNING: If there is a leak at connections (2),
(3) or (4), turn OFF the gas. DO NOT OPERATE
THE GRILL. Contact the Vieluxe
®
Customer
Service at 1-866-VIELUXE.
When leak checks are complete, turn gas supply OFF
at the source and rinse connections with water.
Liquid Propane Cylinder
The liquid propane cylinder manufacturer is
responsible for the materials, workmanship and
performance of the tank. If the tank has a defect
malfunctions, or you have a question regarding the
tank, call the tank manufacturer’s customer service
center. The phone number is on the warning decal,
which is permanently attached to the tank. If the tank
manufacturer has not resolved the issue to your
satisfaction, then contact the Vieluxe
®
Customer
Service at 1-866-VIELUXE.
(1)
(2)
(3)
(4)
Page 11
11
Refilling the Liquid Propane Cylinder
We recommend that you refill the LP cylinder before it
is completely empty.
Removal of the LP cylinder
1) Close cylinder valve (turn clockwise).
2) Unscrew regulator coupling by turning
counterclockwise, by hand only.
3) Loosen cylinder lock wing nut and turn cylinder lock
up out of the way.
4) Lift cylinder off.
To refill, take LP cylinder to a “Gas Propane” dealer.
WARNING: We recommend that your LP cylinder
be filled at an authorized LP gas dealer, by a
qualified attendant, who fills the cylinder by
weight. IMPROPER FILLING IS DANGEROUS.
CAUTION: When transporting the LP cylinder
make sure the plastic dust cover is in place over
the valve. This will keep dust and dirt from the
threaded portion of the valve.
Checking the fuel level in your tank
Check the fuel level by viewing the color indicator level
line on the side of the tank scale.
1) Empty
2) Medium
3) Full
(1)
(2)
(3)
(1)
(3)
(2)
Page 12
12
Safe handling tips for Liquid Propane
Gas Cylinders
■ Liquid Propane (LP) gas is a petroleum product as
are gasoline and natural gas. LP gas is a gas at
regular temperatures and pressures. Under
moderate pressure, inside a cylinder, LP gas is a
liquid. As the pressure is released, the liquid readily
vaporizes and becomes gas.
■ LP gas has an odor similar to natural gas. You
should be aware of this odor.
■ LP gas is heavier than air. Leaking LP gas may
collect in low areas and prevent dispersion.
■ To fill, take the LP cylinder to an RV center, or look
up “gas-propane” in the phone book for other
sources of LP gas.
WARNING: We recommend that your LP cylinder
be filled at an authorized LP gas dealer, by a
qualified attendant, who fills the tank by weight.
IMPROPER FILLING IS DANGEROUS.
WARNING: If you exchange your LP cylinder,
make sure you get a similar tank in return. Your
LP cylinder is equipped with a quick closing
coupling or type 1 valve and an OPD (Overfilling
Prevention Device). Other LP cylinders may not
be compatible with your grill connection.
■ Air must be removed from a new LP cylinder before
the initial filling. Your LP dealer is equipped to do
this.
■ The LP cylinder must be installed, transported and
stored in an upright position. LP cylinders should
not be dropped or handled roughly.
■ Never store or transport the LP cylinder where
temperatures can reach 125° F (too hot to hold by
hand - for example: do not leave the LP cylinder in
a car on a hot day).
Note - A refill will last about 20 hours of cooking time
at normal use. The fuel scale will indicate the propane
supply so you can refill before running out. You do not
have to run out before you refill.
■ Treat “empty” LP cylinders with the same care as
when full. Even when the LP tank is empty of liquid
there still may be gas pressure in the cylinder.
Always close the cylinder valve before
disconnecting.
CAUTION: When transporting the LP cylinder
make sure the plastic dust cover is in place over
the valve. This will keep dust and dirt from the
threaded portion of the valve.
■ Do not use a damaged LP cylinder. Dented or rusty
LP cylinders or LP cylinders with a damaged valve
may be hazardous and should be replaced with a
new one immediately.
Liquid Propane (LP) Cylinder(s)
■ The joint where the hose connects to the LP
cylinder must be leak tested each time the LP
cylinder is reconnected. For example, test each time
the LP cylinder is refilled.
■ Be sure the regulator is mounted with the small
vent hole pointed downward so that it will not collect
water. This vent should be free of dirt, grease,
bugs etc.
■ The LP cylinder and connections supplied with your
Vieluxe
®
gas grill have been designed and tested to
meet government, Canadian Standards
Association, and Underwriters Laboratories
requirements.
Liquid Propane Cylinder requirements
■ Replacement LP cylinders supplied by Weber
satisfy the above requirements. Check to be sure
other cylinders have a D.O.T. certification(1), and
date tested(2) is within five years.Your LP gas
supplier can do this for you.
If you have questions about spare LP cylinders
contact the Vieluxe®Customer Service at
1-866-VIELUXE.
■ All LP tank supply systems must include a collar to
protect the cylinder valve.
■ The LP cylinder must be a 20-lb. size (18 1/4 inches
high, 12 1/4 inches in diameter).
■ The cylinder should be constructed and marked in
accordance with the Specifications for LP - Gas
Cylinders of the U.S. Department of Transportation
(D.O.T.) or the National Standard of Canada,
CAN/CSA-B339, Cylinders, Spheres and Tubes or
Transportation of Dangerous Goods; and
Commission, as applicable.
DOT 4BA240
00/01
(1)
(2)
Page 13
13
WARNING: Before attempting any troubleshooting steps, all gas controls and supply valves should be in
the OFF position.
LP TANK CABINET TROUBLESHOOTING
Problem
Burner does not light.
Flame is low in HIGH position.
Burners do not light. -or- Burners have a
small flickering flame in the HI position.
-or- Grill temperature only reaches 250° to
300° F in the HI position.
Check
Is gas supply off?
Is fuel hose bent or kinked?
The excess flow safety device,
which is part of the grill to cylinder
connection, may have activated.
Cure
Turn supply on.
Straighten hose.
To resest the exess flow
safety device turn all burner
control knobs and the
cylinder valve OFF.
Disconnect the regulator from
the cylinder. Turn burner
control knobs to HI. Wait at
least 1 minute. Turn the
burner control knobs OFF.
Reconnect the regulator to
the cylinder. Turn cylinder
valve on slowly.Refer:
Lighting Instructions".
If problems cannot be corrected by using these methods, please contact Customer Service toll
free at 1-866-VIELUXESM.
© 2003 Vieluxe®, Flavorizer®and Crossover®are registered U.S. trademarks; Gas Catcher™, are trademarks, all of
Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL 60067-6266. U.S.A. 1-866-VIELUXE.
Loading...