PLATINUM
™
SERIES II
LP Gas Barbecues
Step-By-Step Guide
THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.
NOTICE TO INSTALLER: These instructions
must be left with the owner and the owner
should keep them for future use.
FOR Y OUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call your
gas supplier or your fire department.
FOR Y OUR SAFETY
1. Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
2. An LP tank not connected for use shall
not be stored in the vicinity of this or
any other appliance.
WARNING: Follow all leak check
procedures carefully in this manual
prior to barbecue operation. Do this
even if barbecue was dealer assembled.
97460 12/96
Platinum Series II
2200 LP
Platinum Series II
3200 LP
Platinum Series II
3400 LP
R
A P P R O V E D
CANADIAN
GAS ASSOCIATION
®
National
Association
PROPANE
GAS
2
TOOLS NEEDED
Phillips screwdriver
7/16 inch or adjustable wrench
SUPPLIES NEEDED
While we give much attention to our products, unfortunately an occasional error may occur. If a part is
missing, do not go back to the store. Call the Weber
Customer Service Center toll free 1-800-446-1071 to
receive immediate assistance. Have your owner’s
manual and serial number of the barbecue available
for reference.
You will need a soap and water solution to check for gas
leaks. (See section “Check for Gas Leaks.”)
Refer to exploded view in the Operating Guide if
replacement parts are needed.
Your LP tank is shipped empty for safety. After setting the
LP fuel scale you will need to fill it. (See section “Fill LP
Tank.”)
Bottom rack
Bottom tray
Catch pan holder
Catch pan
Drip pan
Four 1/4-20 x 1/2 inch bolts
Four nylon washers
Filler adapter
Bottom tray
Figure 1
REMOVE BOTTOM TRAY FROM GRILL
Remove all tape from packaging. Remove bottom rack
from top of packaging. Remove outer box. Pull out bottom
tray from cooking box. Remove packaging material from
bottom tray, catch pan holder, catch pan, and drip pan.
For the Platinum Series II 3400, remove the white plastic
from the stainless steel.
3
REMOVE GRILL FROM LOWER PACKAGING
WARNING: Lifting the barbecue from the lower
packaging requires at least two people.
With two people lift straight up and over lower packaging
and cardboard support.
Note: For the Platinum Series II 3400, make sure the front
doors are securely closed before lifting.
Figure 2
REMOVE PACKAGED PARTS FROM LOWER CARTON
Left work surface
Right work surface
(Platinum Series II 2200 LP only)
Side burner
(Platinum Series II 3200 LP and 3400 LP only)
LP tank
Note: For the Platinum Series II 3200 and 3400, remove
the white plastic on the stainless steel of the side burner.
4
INSTALLATION OF CATCH PAN INTO BOTTOM TRAY
Slide the bottom tray onto the mounting rails under the
cooking box with finger grip toward you.
CAUTION: Do not line bottom tray with aluminum foil.
It can cause grease fires by trapping the grease and
not allowing grease to flow into the catch pan.
Put the foil drip pan into the catch pan.
Slide the catch pan into the catch pan holder with its
finger grip towards you.
Finger grip
Figure 3
Front of
catch pan
holder
Hook the ends of the catch pan holder into the hole in the
bottom tray. Figure 3. The front of the catch pan holder
must be on the same side as the finger grip of the
bottom tray.
Figure 4
REINSTALLATION OF STAINLESS STEEL FLAVORIZER BARS
Set the short stainless steel Flavorizer bars front to back
in the upper position. Figure 5. Place Steam-N-Chips
Smoker so it opens towards Flavorizer bars.
Note: Remove any tape or packing material. Parts are
shipped in place. Use these steps to check that they are
in position. The Flavorizer bars are already in place.
This step is only for reinstallation.
Set the long stainless steel Flavorizer bars side to side in
the lower position of the cooking box. Insert the front two
Flavorizer bars through the Steam-N-Chips Smoker flue.
Figure 4.
Figure 5
Flue
5
Note:The cooking grates are already in place.This
step is only for reinstallation.
Set the cooking grates onto the ledges in the cooking
box. The open "U" of the cooking grate goes down.
Figure 6.
Set the warming rack into the slots at the rear of the
cooking box. Figure 7.
Figure 6
Figure 7
REINSTALLATION OF COOKING GRATES
INSTALLATION OF WARMING RACK
INSTALL WARM-UP BASKET
Insert one end of the Warm-Up Basket into the hole in the
right end of the lid and the other end into the slot in the
left end of the lid. Figure 8.
Figure 8
6
SET LP FUEL SCALE
You will need: LP tank (empty).
Note - For accuracy, the fuel scale must be set with an
empty tank.
We utilize various LP tank manufacturers. Some of the
tanks we receive have differing top collar assemblies.
(The top collar is the metal protective ring around the
valve.) One series of tanks mounts with the valve facing
front. The other tanks mount with the valve facing away
from the fuel scale. These types of tanks are illustrated in
Figure 9.
Loosen the tank lock wing nut. Tighten so the lock is held
up out of the way. Figure 9 (a). Lift and hook the tank onto
the fuel scale. With an empty LP tank, adjust the fuel scale
setting to E with scale setting (top) wing nut. Figure 9 (b).
CAUTION: Do not remove adjustment wing nut from
tank scale.
After adjusting tank scale, push tank down a couple of
times to check that the tank scale is set on “E”.
F
E
(a)
Scale setting
wing nut
Figure 9
F
E
(b)
FILL LP TANK
To fill, take the LP tank and filler adapter to an RV center,
or look up gas-propane in the phone book for other
sources of LP gas.
WARNING: We recommend that your LP tank be filled
at an authorized LP gas dealer by a qualified
attendant, who fills the tank by weight.
IMPROPER FILLING IS DANGEROUS.
Tell your LP dealer that this is a new LP tank. The air
must be removed from a new LP tank before the initial
filling. Your LP tank dealer is equipped to do this.
CAUTION: If you exchange your LP tank, make sure
you get a similar tank in return.Your LP tank is
equipped with a Type II, CGA #810 quick-disconnect
valve. Other LP tanks are not compatible with your
barbecue connection.
The LP tank must be installed, transported and stored in
an upright position. LP tank should not be dropped or
handled roughly.
Never store or transport the LP tank where temperatures
can reach 125° Fahrenheit (too hot to hold by hand – for
example: do not leave the LP tank in a car on a hot day).
For full instructions on safe handling of LP tanks, see
Section "General Tank Information”.
7
GENERAL TANK INFORMATION
LP Tank Manufacturer
The LP tank manufacturer is responsible for the materials,
workmanship and performance of the tank. If the tank has
a defect, malfunctions, or you have a question regarding
the tank, call the tank manufacturer's customer service
center. The phone number is on the warning decal which is
permanently attached to the tank. If the tank manufacturer
has not resolved the issue to your satisfaction, then call
Weber-Stephen Products Co., Customer Service Center.
For Y our Safety
Your LP tank is shipped empty for safety. After setting the
LP fuel scale you will need to fill it. Refer to Filling your
LP tank.
Safe handling tips for LP Gas
■ Liquid Propane (LP) gas is a petroleum product as are
gasoline and natural gas. LP gas is a gas at regular
temperatures and pressures. Under moderate pressure,
inside a cylinder, LPgas is a liquid. As the pressure is
released the liquid readily vaporizes and becomes gas.
■ LP gas has an odor similar to natural gas. You should
know this odor.
■ LP gas is heavier than air. Leaking LP gas may
collect in low areas that prevent dispersion.
■ The LP tank must be installed, transported and stored
in an upright position. LP tanks should not be
dropped or handled roughly.
■ Never store or transport the LP tank where
temperatures can reach 125° F (too hot to hold by
hand - for example: do not leave the LP tank in a car
on a hot day).
■ The LP cylinder supply must be arranged for vapor
withdrawal.
Note - A refill will last about 20 hours of cooking time at
normal use.The fuel scale will indicate the propane
supply so you can refill before running out.You do not
have to run out before you refill.
■ Treat "empty" LP tanks with the same care as when
full. Even when the LP tank is empty of liquid there
still may be gas pressure in the cylinder. Always
close the tank valve before disconnecting.
■ Do not use a damaged LP tank. Dented or rusty LP
tanks or LP tanks with a damaged valve may be
hazardous and should be replaced with a new one
immediately.
■ The joint where the hose connects to the LP tank
must be leak tested each time the LP tank is
reconnected. For example, test each time the LP tank
is refilled.
■ Be sure the regulator is mounted with the small vent
hole pointed downward so it will not collect water.
This vent should be free of dirt, grease, bugs etc.
■ The LP tank and connections supplied with your
Weber Gas Barbecue have been designed and tested
to meet government, American Gas Association and
Underwriters Laboratories requirements.
■ Replacement LP tanks supplied by Weber satisfy the
requirements. Check to be sure the tank has a D.O.T.
certification, and has been tested within five years.
Your LP gas supplier can do this for you. Figure 10.
If you have questions about spare LP tanks, please
call Weber-Stephen Customer Service.
DOT 4BA240
2/96
Date Tested
20 lb LP tank
D.O.T. Certification (example)
■ All LP tank supply systems must include a collar to
protect the tank valve.
■ The LP tank must be constructed and marked in
accordance with the specifications for LP gas
cylinders of the U.S. Department of Transportation
(D.O.T.).
Figure 10
8
INSTALL WORK
SURFACES
FOR THE PLATINUM SERIES II 2200
You will need...left work surface, right work surface, four
1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16
inch or adjustable wrench.
Insert the left work surface tabs in the slots to the left of
the cooking box. Figure 11 (a). Slip washers on the bolts
and insert the bolts as shown. Tighten. Figure 11 (b).
Insert the right work surface tabs in the slots to the right of
the cooking box. Figure 11 (c). Slip washers on the bolts
and insert the bolts as shown. Tighten. Figure 11 (d).
Platinum Series II 2200
Figure 11
(a)
(b)
(c)
(d)
View from
left side
View from left
underside
View from
right side
View from right
underside
Tabs
Tabs
Tabs
If you have the Platinum Series II 2200,
continue to step “Install Work
Surfaces” on this page.
If you have the Platinum Series II 3200,
go to step “Install Work Surface and
Side Burner” on page 9.
If you have the Platinum Series II 3400,
go to step “Install Work Surface and
Side Burner” on page 11.
After this assembly, proceed to step “Install Bottom
Rack” on page 13.
9
INSTALL WORK SURFACE
AND SIDE BURNER
FOR THE PLATINUM SERIES II 3200
You will need... left work surface, side burner assembly,
four 1/4-20 x 1/2 inch bolts, four nylon washers and a
7/16 inch or adjustable wrench.
Insert the left work surface tabs in the slots to the left of
the cooking box. Figure 12 (a). Slip washers on the bolts
and insert the bolts as shown. Tighten. Figure 12 (b).
Note: Remove protective covers from tabs of
side burners.
Insert the side burner assembly tabs in the slots to the right
of the cooking box. Figure 12 (c). Slip washers on the bolts
and insert the bolts as shown. Tighten. Figure 12 (d).
Side burner can only be installed on right side
of barbecue.
Platinum Series II 3200
Figure 12
Route the side burner hose so it will not interfere with the
scale indicator rod.
The side burner hose is connected in the following
manner:
Slide back the collar of the quick disconnect on the
manifold. Push the male fitting of the side burner hose
into the quick disconnect, and maintain pressure. Slide
the collar closed. Figure 13. Figure 14 shows the quick
disconnect engaged.
View from
left side
View from left
underside
View from
right side
View from right
underside
Manifold side view
Manifold side view
Figure 14
Figure 13
Male fitting
Quick disconnect
engaged
Side burner hose
Tabs
Tabs
Tabs
(d)
(b)
(c)
(a)
View from right
underside
To LP tank
To side burner
connection
Figure 15
10
Check that the side burner is properly assembled.
Figure 16
Burner cap
Burner ring
Burner head
Burner base
Windshield
Grate
(a)
(c)
(b)
Burner orifice
WARNING: Set the burner ring onto the burner head.
Rotate the burner ring until the four lugs on the
burner ring are seated in the four slots on the burner
head. Figure 16 (b).
Note: The burner head has a hole in it that fits over the
igniter electrode.
INSTALL WORK SURFACE
AND SIDE BURNER
FOR THE PLATINUM SERIES II 3200
(CONTINUED)
Slots
Lugs
Igniter
electrode
After this assembly, proceed to step “Install Bottom
Rack” on page 13.
11
INSTALL WORK SURFACE
AND SIDE BURNER
FOR THE PLATINUM SERIES II 3400
Figure 17
Platinum Series II 3400
View from
left side
View from left side
View from
right side
View from right
underside
Tabs
Tabs
Tabs
(d)
(b)
(c)
(a)
You will need... left work surface, side burner assembly,
four 1/4-20 x 1/2 inch bolts, four nylon washers and a
7/16 inch or adjustable wrench.
Insert the left work surface tabs in the slots to the left of
the cooking box. Figure 17 (a). Slip washers on the bolts
and insert the bolts as shown. Tighten. Figure 17 (b).
To install side burner
Note: Remove protective covers from tabs of
side burners.
Insert the side burner assembly tabs in the slots to the right
of the cooking box. Figure 17 (c). Slip washers on the bolts
and insert the bolts as shown. Tighten. Figure 17 (d).
Side burner can only be installed on right side
of barbecue.
Left panel
12
Route the side burner hose around the tank panel so it
will not interfere with scale indicator rod.
The side burner hose is connected in the following
manner:
Slide back the collar of the quick disconnect on the
manifold. Push the male fitting of the side burner hose
into the quick disconnect, and maintain pressure. Slide
the collar closed. Figure 18. Figure 19 shows the quick
disconnect engaged.
Manifold side view
Manifold side view
Figure 19
Figure 18
Male fitting
Quick disconnect
engaged
Side burner hose
View from right
underside
To LP tank
To side burner
connection
Figure 20
Check that the side burner is properly assembled.
Figure 21
Burner cap
Burner ring
Burner head
Burner base
Windshield
Grate
(a)
(c)
(b)
Burner orifice
INSTALL WORK SURFACE
AND SIDE BURNER
FOR THE PLATINUM SERIES II 3400
(CONTINUED)
WARNING: Set the burner ring onto the burner head
with the slots facing up. Rotate the burner ring until
the four lugs on the burner ring are seated in the four
slots on the burner head. Figure 21 (b).
Note: The burner head has a hole in it that fits over the
igniter electrode.
Lugs
Slots
Igniter
electrode
After this assembly, proceed to step “Install Bottom
Rack” on page 13.
13
INSTALL BOTTOM RACK
Figure 22
Place the bottom rack between the frame supports.
Figure 22.
For the Platinum Series II 3400, place the bottom rack
under the cart between the frame supports. Lift up one
end of the rack so it clears the crosspiece. Continue to lift
until the opposite end clears the opposite crosspiece. Set
the rack in place on both crosspieces.
Valves are shipped in the OFF position, but you should
check to be sure. Put the knob on each valve. Check by
pushing down and turning clockwise. If they do not turn,
they are off. Proceed to the next step. Figure 23.
Figure 23
For models 3200 & 3400, check that the side burner
valve is in the OFF position. Push in and turn to OFF.
Figure 24.
Figure 24
CHECK THAT ALL BURNER VALVES ARE OFF
14
CONNECT FILLED LP TANK
WARNING: Make sure that the LP tank valve is
closed. Close by turning clockwise.
Hook the LP tank onto the fuel scale. Loosen the tank
lock wing nut. Swing the tank lock down. Tighten the wing
nut. Figure 25.
Figure 25
Tank lock wing
nut
Remove the tape and packaging from the hose and regulator.
Route the hose so it will not interfere with the scale
indicator rod.
The hose and regulator are connected in the following manner:
Slide back the collar of the quick disconnect on the tank
valve. Push the male fitting of the regulator into the quick
disconnect, and maintain pressure. Slide the collar closed.
Figure 26 (a). Figure 26 (b) shows the quick disconnect
engaged and various components of the tank and
regulator. Regulator vent hole should be at 3, 6, or 9
o'clock. It should not be pointed up. Figure 26 (c).
Figure 26
Turn so regulator vent
does not collect water
Hose
Quick disconnect
engaged
Valve handwheel
close clockwise
Tank valve
Collar
Male
fitting
Pressure
relief valve
Tank
Regulator
Regulator
vent
(a)
(b)
(c)
15
CHECK FOR GAS LEAKS
WARNING
The gas connections of your Weber Gas
Barbecue have been factory tested. We do
however recommend that you leak check all
gas connections before operating your
Weber Gas Barbecue.
Remove the knobs from the control panel. Figure 27.
Figure 28
Figure 27
Use a Phillips screwdriver to remove the screws from the
underside of the control panel. Figure 28.
Stand at the right end of the barbecue. Lift the control
panel off. The side burner or work surface remains
in place.
View from right
underside
WARNING: You should check for gas leaks every time
you disconnect and reconnect a gas fitting.
You will need: a soap and water solution and a rag or
brush to apply it.
Note - Since some leaks test solutions, including soap
and water, may be slightly corrosive, all connections
should be rinsed with water after checking for leaks.
DANGER
Do not use an open flame to check for
gas leaks. Be sure there are no sparks or
open flames in the area while you check for
leaks. This will result in a fire or explosion
which can cause serious bodily injury or
death and damage to property.
Figure 29
To perform leak checks: open tank valve by turning the
tank valve handwheel counterclockwise. Figure 29.
WARNING
Make sure all burner control knobs are in
the OFF position, including the side burner,
if the barbecue has a side burner.
16
CHECK FOR GAS LEAKS
WARNING: Do not ignite burners while checking
for leaks.
Check for leaks by wetting the connections with the soap
and water solution and watching for bubbles. If bubbles
form or if a bubble grows there is a leak.
Check:
a) Hose to manifold connection. Figure 30 (a).
WARNING: If there is a leak at connection a, retighten
the fitting with a wrench and recheck for leaks with
soap and water solution.
If a leak persists after retightening the fitting, turn
OFF the gas. DO NOT OPERATE THE BARBECUE.
Contact Weber-Stephen Customer Service.
b) Regulator to tank connection. Figure 30 (b).
c) Manifold to side burner hose connection.
Figure 30 (c).
d) Valves to manifold connections. Figure 30 (d).
e) Side burner hose to side burner valve, and side
burner supply line to side burner valve. Figure 30 (e).
f) Side burner supply line to side burner orifice
connection. Figure 30 (f).
g) Hose to regulator connection. Figure 30 (g).
WARNING: If there is a leak at connections
b, c, d, e, f or g, turn OFF the gas. DO NOT OPERATE
THE BARBECUE. Contact W eber-Stephen
Customer Service.
When leak checks are complete, turn gas supply OFF at
the source and rinse connections with water.
Figure 30
(a) (b)
(c)
(g)
(e)
(d)
views from
below
(f)
17
REINSTALL THE CONTROL PANEL
Set the control panel in place over both frame braces.
(Hold the Crossover Ignition button up while setting the
control panel in place.) Slip washers on Phillips screws,
insert into holes as shown, and tighten. Figure 31 (a).
Push on the burner control knobs. Figure 31 (b).
Figure 31
REFER TO OPERATING
GUIDE BEFORE LIGHTING
BARBECUE
Underside view
of right work
surface or side
burner
18
Loading...