Page 1
Webee Switchee
GETTING STARTED WITH SWITCHEE
1
GETTING STARTED WITH SWITCHEE
This document is the property of Webee L.L.C.. The data contained here, in whole or in part, may not be duplicated, used or
disclosed outside the recipient for any purpose. This restriction does not limit the recipient's right to use information contained
in the data if it is obtained from another source without restriction.
Page 2
Webee Switchee
GETTING STARTED WITH SWITCHEE
2
Getting started
Page 0
© 2014 Webee LLC, All rights reserved. The Webee logo, Boss and Bees are trademarks or registered trademarks of Webee LLC
INDEX
Section 1: Mounting your Switchee
To an electrical switch........................................................03
Diagram 1..........................................................................04
To a power outlet...............................................................05
Diagram 2..........................................................................05
Section 2: Connecting to Smartee
Adding Switchee to Zigbee Network..................................06
Removing Switchee from Zigbee Network..........................06
Section 3: Specs
Electrical Specifications......................................................07
Load control Specifications.................................................07
RF characteristics...............................................................08
Dimensions.........................................................................08
Section 4: Security Instructions
Security Guidelines.............................................................09
Page 3
Webee Switchee
GETTING STARTED WITH SWITCHEE
3
MOUNTING YOUR SWITCHEE
Getting started
© 2014 Webee LLC, All rights reserved. The Webee logo, Boss and Bees are trademarks or registered trademarks of Webee LLC
1
1
Page 0
In order to connect the Switchee to your existing electrical switch follow these steps:
1- off Make sure the electricity at home is ; in order to safety handle the device. As you will be
connecting the wires from your electrical current to the Swicthee is imperative that the
electricity is disabled.
2- Identify the Load 1 and Load 2 (see Diagram 1 on page 4). Each Load works separately as
two different power outputs.
Ÿ a. Connect the 2 wires from your outlet (could be from any electrical system such as
lamps, lights, etc) to the Load1-A and Load1-B connectors on the Switchee. When
connecting make sure to do it carefully as it could represent an electrical hazard since
these wires will allow AC current to flow through them.
Ÿ b. To use the Load 2 to connect another electrical system, repeat the process by
connecting the two wires from the second electrical system to Load2-A and Load2-B
connectors on the Switchee. Once again, do it carefully to avoid electrical hazards.
3- Connect the COM (common connector) to your switch (or switches depending if you will
be using both power outputs Load1 and Load2) as shown on the Diagram 1 on page 4.
4- Connect the SW1 to the connector left on the switch that will be controlling Load1. And
connect SW2 to the connector left on the switch that will be controlling Load2, as shown on
Diagram1. The connectors SW1, SW2 and COM are signaling ports. They do not represent
an electrical hazard as they use only 5v for signaling purposes. The switches will function as
toggle button once they are properly connected. Which means you will be able to turn the
controlled devices on/off not only with your Webee App, but also manually.
5- Last, connect the L connector on your Switchee to the phase Live wire of your electrical
wiring and N connector of the Switchee to the Neutral wire of your electrical wiring (see
Diagram 1 on page 4)
To an electrical switch
Page 4
Webee Switchee
GETTING STARTED WITH SWITCHEE
4
Page 0
Diagram 1 Mounting Switchee to an electrical switch.:
Getting started
© 2014 Webee LLC, All rights reserved. The Webee logo, Boss and Bees are trademarks or registered trademarks of Webee LLC
Page 5
Webee Switchee
GETTING STARTED WITH SWITCHEE
5
Getting started
Page 0
In order to connect the Switchee to your existing power outlet follow these steps:
1- Make sure the electricity at home is off, in order to safety handle the device. As you will be
connecting the wires from your electrical current to the Swicthee is imperative that the
electricity is disabled.
2- Identify the Load 1 and Load 2 (see Diagram 2 bellow). Each Load works separately as
two different power outputs.
Ÿ a. Connect the 2 wires from your outlet (could be from any electrical system such as
lamps, lights, etc) to the Load1-A and Load1-B connectors on the Switchee. When
connecting make sure to do it carefully as it could represent an electrical hazard since
these wires will allow AC current to flow through them.
Ÿ b. To use the Load 2 to connect another electrical system, repeat the process by
connecting the two wires from the second electrical system to Load2-A and Load2-B
connectors on the Switchee. Once again, do it carefully to avoid electrical hazards.
Ÿ
3- Last, connect the L connector on your Switchee to the phase Live wire of your electrical
wiring and N connector of the Switchee to the Neutral wire of your electrical wiring (see
Diagram 2 bellow)
To a power outlet
Diagram Mounting Switchee to a power outlet2:
© 2014 Webee LLC, All rights reserved. The Webee logo, Boss and Bees are trademarks or registered trademarks of Webee LLC
Page 6
Webee Switchee
GETTING STARTED WITH SWITCHEE
6
CONNECTING TO SMARTEE
Getting started
© 2014 Webee LLC, All rights reserved. The Webee logo, Boss and Bees are trademarks or registered trademarks of Webee LLC
1
2
Page 0
To join the Switchee to the Smartee, click on the “Add Device” function of your App and
the Smartee will automatically connect your Switchee to the network. For more detailed
instructions check our Smartee User Manual.
If the Switchee does not automatically join the network, press and hold the Config
button. The Switchee will continuously blink erratically as it attempts to join the hub.
Upon a successful joining of the Switchee to the ZigBee network of your Smartee, the
status LED will stop blinking.
If the after following these steps the Switchee will not join the Smartee Zigbee network,
do as follows:
• Make sure the network on your Smartee is open for joining. Keep in mind that once you
clicked on Add Devices, the network will be open for 60 seconds.
•Check if the Switchee hasn’t join another network (the light will be static), see the next
step to learn how to remove it from a network in order to add it to a new one.
Once the Switchee is added to your Smartee, you will be able to start controlling it
trough your Webee App.
If it becomes necessary to remove the Switchee from a Zigbee network then you must
factory default the Switchee. To factory default the Switchee:
A. Press and hold the Switchee's CONFIG button for 5-8 seconds.
B.When the Led blinks twice release the button, LED will start blinking erratically.
C. The Switchee will now be reset to factory defaults and begin scanning for a ZigBee
network to join.
Adding to Zigbee Network
Removing from Zigbee Network
Page 7
Webee Switchee
GETTING STARTED WITH SWITCHEE
7
SWITCHEE’S SPECS
1
323
Description
Min
Typ
Max
Unit
Input voltage range
90-264
VAC
Input frequency
47-63
Hz
Operating temperature
-40-+70
ºC
Storage temperature
-40-+85
ºC (95% RH)
Operating Humidity
--85%
RH
Input current
-
45mA/115VAC
23mA/230VAC
-
mA/VAC
Electrical specifications of power supply
Description
Min
Typ
Max
Unit
Output voltage range
90-264
VAC
Input frequency
47-63
Hz
Total power output
--2500
W
P o w e r o u t p u t p e r
channel (using one
channel)
--2500 @ 230VAC
1600 @ 115VAC
W
P o w e r o u t p u t p e r
channel (using two
channels)
--1250 @ 230VAC
1250 @ 115VAC
W
Load control specifications
Page 0
Getting started
© 2014 Webee LLC, All rights reserved. The Webee logo, Boss and Bees are trademarks or registered trademarks of Webee LLC
Page 8
Webee Switchee
GETTING STARTED WITH SWITCHEE
8
Description
Min
Typ
Max
Unit
Frequency
2405
-
2480
MHZ
Power output
-40-20
dBm
Sensitivity
-10
-103
-97
dBm
RF Characteristics
Dimensions
Getting started
© 2014 Webee LLC, All rights reserved. The Webee logo, Boss and Bees are trademarks or registered trademarks of Webee LLC
Page 0
Page 9
Webee Switchee
GETTING STARTED WITH SWITCHEE
9
SAFETY INSTRUCTIONS
Getting started
© 2014 Webee LLC, All rights reserved. The Webee logo, Boss and Bees are trademarks or registered trademarks of Webee LLC
1
4
Page 0
Safety Guidelines
-To be installed and/or used in accordance with appropriate electrical
codes and regulations.
-If you are unsure about any of these instructions, consult a
qualified electrician.
-Follow all guidelines carefully, if you have any questions contact us at
support@webeelife.com.
Warning:
Make sure to veriffy that the devices you are
connecting are within the electrical range of
the Swicthee. Check electrical specifications.
Otherwise, it will be damage and will no longer
function.
Page 10
Webee Switchee
GETTING STARTED WITH SWITCHEE
10
V1.0 REV. January, 2015
© 2014 Webee LLC, All rights reserved. The Webee logo, Boss and Bees are trademarks or registered trademarks of Webee LLC
Loading...