Webb WER16SP Operator's & Parts Manual

OPERATOR’S MANUAL AND PARTS LIST

SELF PROPELLED PETROL LAWNMOWER

WER16SP

Spares & Support: 01793 333212

www.webblawnmowers.co.uk

Before use please read & understand this manual, paying particular attention to

the safety instructions.

193837001 14/11/2014 v2

Thank you for choosing our petrol lawnmower.

To ensure that you get the best results from your petrol lawnmower please read all of these safety and

operating instructions carefully before using this product.

TABLE OF CONTENTS PRODUCT SPECIFICATION

Product Specifications……………………….1

Safety Rules……………………………….1-3 Model number WER16SP (193837001)

Assembly/Pre-Operation……………….....3-6 Petrol engine B&S 450e series 125cc

Operation……………………………….....7-9 Engine speed 2800rpm

Maintenance……………………………...9-11 Cutting width 420mm
Storage……………………………………...10 Adjustable cutting height 15-65mm
Environment…………………….………….10 Grass collection capacity 40L

Parts Diagram and Lists...………………11-16 Sound Pressure Level 90.8 dB(A)

DOC………………………………………..17 Guaranteed Sound Power Level 96dB(A)

Warranty……………..............................18-19 Max. vibration value 2.67m/ s

2

Also Available From Webb…………….......21 Steel Deck

Warranty Registration…………………..22-23

IMPORTANT: Failure to observe the following safety instructions could result in serious injury.
WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making

repairs, always the disconnect the spark plug lead.

CAUTION: Exhaust and other engine parts become extremely hot during operation and remain hot after

engine has stopped. To avoid severe burns on contact, stay away from these areas.

Drive lever

Brake lever

Grass collector

Height adjust handle

Triangle knob

B&S 450E series

Hose connector

Fuel cap

Air Filter

Starter Handle

1

1. GENERAL OPERATION AND SAFETY RULES

z Read the instructions carefully. Be familiar with the controls and the proper use of the equipment.
z Do not put your hands or feet near or under rotating parts. Keep clear of the discharge opening at all

times.

z Only allow responsible individuals, who are familiar with the instructions, to operate the machine.
z Thoroughly inspect the area where equipment is to be used and remove all objects, which could be

thrown by the machine.

z Never mow while people, especially children, or pets are nearby.
z While mowing, always wear appropriate footwear and trousers. Do not operate the equipment when

barefoot or wearing open sandals.

z Do not pull the mower backwards unless absolutely necessary.
z Never operate the lawnmower with defective guards, or without safety devices, for example

deflectors and/or grass catchers, in place.

z Only use accessories approved by the manufacturer.
z Stop the blade(s) when crossing gravel drives, paths, or roads.
z Stop the engine and disconnect the spark plug:

- before clearing blockages or unclogging the chute.

- before checking, cleaning or working on the lawnmower.

- after striking a foreign object. Inspect the lawnmower for damage and make repairs before

restarting and operating the lawnmower.

- if lawnmower starts to vibrate abnormally (check immediately).

z Shut the engine off and wait until it has come to a complete stop before removing the grass catcher.
z Mow only in daylight or good artificial light.
z Do not operate the machine while under the influence of alcohol or drugs.
z Never operate machine in wet grass, this could cause slipping.
z Keep a firm hold on the handle and walk; never run.
z Disengage the self-propelled mechanism before starting the engine.
z Always wear safety goggles or safety glasses with side shields when operating the mower.
z Remove obstacles such as rocks, tree limbs, etc.
z Watch for holes, ruts, or bumps. Tall grass can hide obstacles.
z Do not trim near drop-offs, ditches or embankments. The operator could lose their footing or balance.
z Do not mow excessively steep slopes.
z Keep in mind that the operator or user is responsible for accidents or hazards involving the machine

that could occur to other people or their property.

z Be alert and turn the machine off if children enter the area.
z For wheel

ed ro

tary machines, mow across the face of slopes, never up and down.

z Never allow children or people unfamiliar with these instructions to use the lawnmower.
z WARNING-Petrol is highly flammable.

- store fuel in containers specifically designed for this purpose;

- refuel outdoors only and do not smoke while refueling;

- add fuel before starting the engine. Never remove the cap of the fuel tank or add petrol while the

engine is running or when the engine is hot;

- if petrol is spilled, do not attempt to start the engine but move the machine away from the area

of spillage and avoid creating any source of ignition until the petrol vapours have dissipated;

- replace fuel tanks and container caps securely.

2

z Before using, always visually inspect to ensure that the blade, blade bolts and cutter assembly are not

worn or damaged. Replace worn or damaged blades and bolts in sets to preserve balance.

z Never tamper with safety devices. Regularly check that they are operating properly.
z Keep the machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow the

machine to cool before storing.

z Exercise extreme caution when changing direction on slopes.
z Never attempt to make wheel height adjustments while the engine is running.
z Grass catcher components are subject to wear, damage, and deterioration, which could expose

moving parts or allow objects to be thrown. Frequently check components and replace with the

manufacturer’s recommended parts, when necessary.

z The mower blades are extremely sharp. Wrap the blade, wear gloves, and use extra caution when

servicing them.

z Do not change the engine governor setting or over-rev the engine.
z Stop the engine if the lawnmower has to be tilted for transportation when crossing surfaces other than

grass, and when transporting the lawnmower to and from the area to be mowed.

z Disengage the drive clutch before starting the engine.
z Start the engine carefully according to the instructions, with your feet well away from the blade.
z Do not tilt the lawnmower when starting the engine or cutting.
z Do not start the engine when standing in front of the discharge chute.
z Never pick up or carry a lawnmower while the engine is running.

DANGER – Rotating Warning! Keep hands
Read blades. Keep hands and feet clear of the
Operator’s and feet out of cutting deck when the
Manual. Openings while machine is running.
. Machine is running.

Warning! Before starting
Keep Before you work on any repair work, remove
Bystanders the cutting equipment, the spark plug cable
Away. remove the spark plug from the spark plug.
socket.

Warning! Keep other persons

Remove Objects that could at a safe distance when

Be thrown by the blade. using this lawnmower.

ASSEMBLY/PRE-OPERATION

Read this instruction manual in its entirety before you assemble or operate your new lawnmower.

IMPORTANT: The lawnmower is shipped WITHOUT OIL OR PETROL in the engine.

Your new lawnmower has been assembled and tested at the factory.

Roll the lawnmower out of the carton and check the carton thoroughly for additional loose parts.

3

To avoid damage during the transport process, the drive and brake cables for your machine may not be

fitted to their appropriate handle bar.

The front cable is the brake cable, which is to be fitted to the front lever on your machine, this is the

Operator Presence Control Lever (OPC). The cable at the rear is your drive cable, which is to be fitted to

the rear lever, which is your Drive Lever.

Apply inward pressure to the lever assembly on the left hand side of the machine, to remove the lever lug

from the handle assembly.

Brake Cable

Drive Cable

4

Insert the Brake Cable into the OPC Lever.

Insert the Drive Cable into the Drive Lever.

Re-seat the lever assembly back into the main handle.

5

INST ALL A TT ACHMENTS

Your lawnmower was shipped ready to be used as a rear bag mower.

The mower has three different operating modes.

1. Collecting:

• Fit the grassbox by lifting the rear flap on the mower and hook the front of the box to the shaft on the

mower.

• Lower the flap to lock the grassbox in position.

• When the box is full, the grass will be visible through the viewing window in the top of the box.

• Stop the engine before emptying the grassbox.

2. Rear Discharge:

• With the grassbox removed and the rear flap in the down position, the mower will cut and discharge the

grass from the rear of the machine.

3. Mulching:

• Fit the mulch plug to the rear discharge opening of the mower and close the rear flap.

• The mower will now recycle the chopped grass into the lawn surface.

• To mulch efficiently only cut one third of the length of the grass.

ASSEMBLE HANDLE

Fit the Lower Handle to the frame of the lawnmower.

Insert 1x Square Neck Bolt M8x30 in the lower hole of the handle and frame from the outside.

Once through, add the Flat Washer and Small Triangle Knob with M8 Hex Nut, tighten until they are

secure.

Enter Hex Bolt M8x16 into the second lower handle fixing and frame hole from the outside.

Once through, add Lock Nut M8/8.8 and tighten.

Fit the Top Handle to the Lower Handle.

There are two holes in the Upper Handle, insert the Carriage Bolt M8x50 from the inside through the

Lower Handle and your selected hole in the Upper Handle to assemble the handle at your chosen height.

Once through, fit a Flat Washer and Large Triangle Knob with an M8 Hex Nut, tighten until they are

secure.

6

OPERATION

Operator Presence Control (OPC) Bar - must be held down to the handle to start the engine. Release to

stop the engine.

Starter rope - used to start the engine.
Drive control lever - used to engage self- propelled motion of the lawn mower.

LAWNMOWER ENGINE SPEED

The engine speed was set at the factory for optimum performance. Speed is not adjustable.

DRIVE CONTROL (Model: WER16SP)

z The drive is controlled by holding the Operator Presence Control bar down to the handle and pulling

the drive control lever back towards the handle.
z Forward motion will stop when the operator presence control bar is released. To stop forward motion

without stopping the engine release the drive control lever until the drive control disengages and hold the

operator presence control bar down against handle to continue mowing without the drive.

ADJUST CUTTING HEIGHT

Lower the cutting deck for a low cut and raise the deck for a high cut; adjust cutting height to suit your

requirements. Medium position is best for most lawns.

7

BEFORE STARTING ENGINE ADD OIL

Before each subsequent use the oil level must be checked and if necessary topped up with SAE30 engine

oil.

OIL FILLER CAP/DIPSTICK

Your lawnmower is shipped without oil in the engine.

CAUTION: DO NOT overfill the engine with oil, or it will smoke heavily from the exhaust on startup.

1. Be sure that the lawnmower is on level ground.

2. Remove the oil dipstick from the oil fill spout.

3. Insert and tighten the dipstick.

IMPORTANT:

z Check the oil level before each use. Add oil if needed. Fill to the full line on the dipstick.
z Change the oil after every 25 hours of operation or each season. You may need to change the oil

more often under dusty, dirty conditions. See “TO CHANGE ENGINE OIL” in the Maintenance

section of this manual.

ADD PETROL

z Fill fuel tank to the bottom of the tank filler neck. Do not overfill. Use fresh, clean, regular unleaded

petrol. Do not mix oil with petrol. Purchase fuel in quantities that can be used within 30 days to

ensure fuel freshness. Old or stale fuel can cause damage to the engine carburettor which would

not be covered under the warranty.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use petrol near an open flame.

FUEL TANK CAP

UPPER LIMIT

LOWER LIMIT

8

CAUTION: To avoid engine problems, the fuel system should be emptied before being stored for 30 days

or more. Empty the fuel tank, start the engine and let it run until the fuel lines and carburettor are empty.

Use fresh fuel for your next use of the machine. See Storage Instructions for additional information.

Never use engine or carburettor cleaner products in the fuel tank, permanent damage may occur.

START ENGINE

To start the engine, first make sure that the spark plug is tightened and that the machine is filled with

sufficient oil and petrol.

NOTE: Due to the protective coating on the engine, a small amount of smoke may be present during the

initial use of the product and should be considered normal.

Press the primer bulb 3 times to allow fuel into the engine (for the first use, press 5 times).

Hold the Operator Presence Control bar down to the handle and pull the starter handle quickly.

Do not allow the starter rope to snap back.

STOP ENGINE

z To stop engine, release the Operator Presence Control bar.
z Disconnect the spark plug cap if the lawnmower is to be left unattended.

MOWING TIPS

z Under certain conditions, such as very tall grass, it may be necessary to raise the height of the cut to

reduce the pushing effort and to keep from overloading the engine and leaving clumps of grass

clippings. It may also be necessary to reduce ground speed and/or run the lawnmower over the area a

second time.

z For extremely heavy cutting, reduce the width of cut by overlapping the previously cut area and mow

slowly.

z Pores in cloth grass catchers can become filled with dirt and dust during use and catchers will collect

less grass. To prevent this, regularly hose the catcher off with water and let it dry before using.

z Keep the top of the engine around the starter clean and clear of grass clippings and chaff. This will

assist engine air flow and extend engine life.

MAINTENANCE
IMPORTANT-Regular, careful maintenance is essential for keeping the safety level and original
performance of the machine unchanged over time.

1) Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. Regular

maintenance is essential for safety and performance.

2) Never store the equipment with fuel in the tank inside a building where vapour may reach a flame,

spark or source of extreme heat.

3) Allow the engine to cool before storing in an enclosed space.

4) To reduce the fire hazard, keep the engine, exhaust silencer, battery compartment and fuel storage area

free of grass, leaves, or excessive grease. Remove grass cuttings from containers before storage.

5) Do not use equipment with worn or damaged parts. Parts should be replaced not repaired. Only use

genuine spare parts. Parts that are not of the same quality can damage the equipment and create safety

hazards.

6) If the fuel tank has to be drained, this should be done outdoors and when the engine is cool.

7) Wear strong work gloves when removing and reassembling the blade.

9

8) Check the blade’s balance after sharpening.

9) Check the self-closing guard and grass-catcher frequently for wear and deterioration.

10) Whenever the machine is to be handled, transported or tilted you must:

- Wear strong working gloves.

- Grasp the machine at the points that offer a safe grip, clear of the blade and taking account of the weight

of the machine and its distribution.

CLEANING

Your lawnmower has been supplied with a hose pipe connector towards the back of the deck. This enables

you to clean your machine, using your garden hose. Clip the hose to the machine using a standard hose

connector. Turn on your tap. Ensure that any trailing hose is away from the machine deck. Start the

machine. The momentum of the blade rotation will force water around the deck to clean it.

Carefully clean the machine after each cut to ensure an easy start-up next time you use the machine. Be

sure to remove grass debris and mud accumulated inside the chassis before it dries.

If you need to tilt the mower while cleaning always tip it backwards towards the handles, do not tip it on

its side as this will cause oil to enter the carburettor or exhaust.

The paintwork on the inside of the chassis may peel off over time due to the abrasive action of the cut

grass; when this occurs you must touch up the paintwork using a rustproof paint as soon as possible to

prevent the formation of rust that would lead to corrosion of the metal.

Remove the transmission casing by removing the screws and clean around the transmission and drive

belts with a brush or compressed air once or twice a year.

Once every season, the drive wheels should be cleaned internally. Remove both wheels. Clean the gear

wheel and the wheel gear rim of grass and dirt using a brush or compressed air.

CHANGING BLADES

Empty the oil tank before removing the blade.

To replace the blade, undo the screw.

Reinstall as illustrated. Tighten the screw properly. Tightening torque 45 Nm.
When replacing the blade, the blade screw should also be replaced.

STORAGE
The same petrol must not remain in the tank for more than 30 days.
Thoroughly clean the mower and store it indoors in a dry place.

THE ENVIRONMENT

In order to protect the environment, we recommend that the following points should be given special

consideration:

z Always use pure unleaded petrol.
z Always use a funnel and/or petrol can with a level control to avoid spillage when refilling the fuel

tank.

z Do not fill the fuel tank completely.
z Do not overfill with engine oil.
z When changing the oil, ensure that all the used oil is collected. Avoid spillage. Take the used oil to a

recycling unit.

10

z Do not dispose of used oil in a rubbish bin. Take it to a recycling unit.
z Replace the silencer if faulty. Always use the Manufacturer’s original spare parts.
z Always seek professional help when the carburettor requires adjustment.
z Clean the air filter according to the instructions.

PARTS DIAGRAM AND LIST – HANDLE ASSEMBLY

Item No Part Number Description Qty Item No Part Number Description Qty

1 QG112-1 Foam Handle Cover 1 13 WE113-17 Flat Washer 8.4x16x1.6 4
2 QG112-2 Brake Lever 1 14 WE113-72 Carriage Bolt M8x50 2
3 WE113-8 Bolt M6x30 2 15 WE113-74 Triangle Knob Small (Grey) 2
4 WE113-10 Plastic Stopper 1 16 QG112-4 Square Neck Bolt M8x32/8.8 2
5 WE113-7 Brake Cable Assembly Plate 1 17 QG112-5 Square Neck Bolt M8x20/8.8 2
6 WE113-9 Lock Nut M6/8.8 2 18 QG112-6 Lower Handle 2
7 WE113-4 Top Handle 1 19 WE113-21 Cable Fastener 1
8 WE113-5 Rope Guide 1 20 QG112-7 Small Knob 2

9 WE113-6 Cap Nut M6/8.8 1 21 QG112-8 Handle Stopper 2
10 QG112-3 Brake Cable 1 22 WE117-1 Self Propelled Cable 1
11 WE113-19 Hex Nut M8 6 23 WE117-2 Self Propelled Lever 1
12 WE113-73 Triangle Knob Large (Grey) 2

11

PARTS DIAGRAM AND LIST – DECK ASSEMBLY

Item

No

Part

Number

Description Qty

Item

No

Part

Number

Description Qty

1 WE116-2 B&S 450e Petrol Engine 1 13 QG112-17 Height Adjustment Rod 1
2 QG112-10 Self-Tapping Screw ST6.3x18 2 14 WE117-3 Self-Tapping Screw 5
3 QG112-11 Large Washer 6x18x1.6 2 15 WE117-4 Deck 1
4 WE113-9 Lock Nut M6/8.8 3 16 QG112-20 Height Adjustment Board 1
5 QG112-12 Rear Discharge Base A 2 17 QG112-21 Right Rear Bracket 1
6 QG112-13 Rear Discharge Base B 1 18 WE113-25 "O" Ring 11.2x2.65 1
7 QG112-14 Bolt M6x16 3 19 WE113-26 Hose Connector Inlet 1
8 WE113-12 Lock Nut M8/8.8 6 20 WE113-27 Hose Connector Nut M12x1.25 1

9 QG112-15 Left Rear Bracket 1 21 WE113-28 Cable Stopper 1
10 WE113-34 Square Neck Bolt M8x15/8.8 6 22 WE117-5 Pressure Plate 2
11 WE113-42 Lock Nut M6/8.8 4 23 WE117-23 Mulch Plug 1
12 QG112-16 Bolt M6x12 4

12

PARTS DIAGRAM AND LIST – FRONT AXLE ASSEMBLY

Item No Part Number Description Qty

1 QG112-20 Wheel Trim (Grey) 2
2 WE113-52 Lock Nut M8 2
3 WE113-51 Wheel Bearing 4
4 QG112-21 Front Wheel 2
5 QG112-22 Front Axle 1
6 WE113-40 R Pin 1.5x25 1

13

PARTS DIAGRAM AND LIST – REAR AXLE ASSEMBLY

Item No Part No Descriptio n Qty Item No Part No Description Qty

1 WE113-40 R Pin 1.5x25 1 10

WE113-51

Bearing 4

2 WE117-6 Drive Cog Left 1 11 WE117-21 Wheel 2
3 WE117-7 Drive Pin 2 12 WE117-13 Inner Wheel Cover 2
4 WE117-8 Self-Propelled Washer 4 13 WE117-14 Height Adjuster Handle 1
5 WE117-9 Spring Washer 6 14 WE117-15 Rear Wheel Axle Sleeve 2
6 WE117-10 Drive Cog Right 1 15 WE117-16 Self-Propelled Spring 1
7 WE117-11 Rear Axle 1 16 WE117-17 Gearbox Assembly 1
8 WE117-12 Wheel Trim (Grey) 2 17 WE117-18 Drive V Belt 1
9 WE113-52 Lock Nut M8 2 10 WE113-51 Bearing 4

14

PARTS DIAGRAM AND LIST – GRASS COLLECTOR ASSEMBLY

Item No Part Number Description Qty

1 QG112-26 Lock Washer 2
2 QG112-27 Rear Discharge Cover 1
3 WE113-64 Rear Discharge Cover Spring 1
4 QG112-28 Rear Discharge Cover Shaft 1
5 QG112-29 Grass Collector Breather 1
6 QG112-30 Grass Collector Board 1
7 QG112-31 Grass Collector Top 1
8 QG112-32 Gasket 4

9 QG112-33 Self-Tapping Screw ST6.3x14 4
10 QG112-34 Grass Collector Frame 1
11 QG112-35 Grass Collector Bag (Unbranded) 1

15

PARTS DIAGRAM AND LIST – BLADE ASSEMBLY

Item No Part Number Description Qty

1 WE114-19 Chassis bushing 2
2 WE117-19 Belt Cover 1
3 WE114-21 Hex Self-Tapping Screw 3/8-16x1ST 1
4 WE114-20 Hex Self-Tapping Screw 3/8-16x1ST 30mm 2
5 WE117-20 Blade Adapter 1
6 QG113-37 Blade 1
7 WE113-70 Blade Washer 1
8 WE113-71 Hex Flange Bolt 50mm 1

16

EC Declaration of Conformity

We, Importer

Handy Distribution

SN3 5HY

Declare that the product

Designation: 125cc Petrol Lawnmower

Model: WER16SP

Complies with the following directives:

2006/42/EC- Machinery Directive

2004/108/EC- Electromagnetic Compatibility Directive

2000/14/EC amended by 2005/88/EC- Noise Emission in the Environment by Equipment for

Use Outdoors Directive.

The conformity assessment procedure followed was in accordance with

Directive 2006/42/EC Annex VI

Name of the Notified Body: TÜV Product Service

Address: No. 88 Heng Tong Road, Shanghai 200070, P.R. China

-Measured Sound Pressure Level: 90.8 dB (A)

-Guaranteed Sound Power Level: 96 dB (A)

Standards and technical specifications referred to:

EN 836/A3:2004

ZEK01.2-08.2008

EN ISO 14982:2009

EN ISO 3744:1995

ISO 11094:1991

Authorised signatory and technical file holder

Date: 30/7/2014

Signature:
Name / title: Mr. Simon Belcher / Managing Director

Murdock Rd, Swindon, Wiltshire, SN3 5HY.

17

GJ HANDY & CO LTD USER WARRANTY POLICY

GJ Handy & Co Ltd reserve the right to change specifications and/or price without notice

Version 2 08-2014

1. Users Statement of Warranty

Each new machine is warranted against defective material or assembly of material under normal usage. The
warranty applies to the original purchaser and covers faulty parts and the labour involved in replacing and
repairing those parts, which are of original manufacture.

2. Period of Warranty
All Webb, Handy Pro (Brushcutter & Long Handle Hedgecutter only) and Sanli domestic products

(a) 2 years from the original date of sale to the first domestic user.

(b) 90 days from the original date of sale to the professional/commercial user.

(c) 90 days from the original date of sale when used for hire.

(d) Engines as per the manufacturer’s warranty statement which will be supplied with the machine.

(e) 90 days from the original date of purchase for Replacement Spare Parts.

(f) All machines must be serviced within the first 12 months from the original date of purchase to comply

with the warranty, failure to do so will invalidate the second year of the warranty.

(g) A reduced warranty period of 90 days applies to those items which are subject to normal wear and tear

(e.g. wheels, tyres, cutter bars, cylinders, bottom blades, belts, cables, grass bags, spark plugs).

All Handy, Handy Pro (All others), Mowerland and Q-Garden domestic products

(a) 1 year from the original date of sale to the first domestic user.

(b) 90 days from the original date of sale to the professional/commercial user.

(c) 90 days from the original date of sale when used for hire.

(d) Engines as per the manufacturer’s warranty statement which will be supplied with the machine.

(e) 90 days from the original date of purchase for Replacement Spare Parts.

(f) A reduced warranty period of 90 days applies to those items which are subject to normal wear and tear

(e.g. wheels, tyres, cutter bars, cylinders, bottom blades, belts, cables, grass bags, spark plugs).

All warranty repairs must be undertaken by an authorised service dealer. These dealers have been accredited

by GJ Handy & Co Ltd and agree to only use genuine parts and follow our repair procedures.

18

GJ HANDY & CO LTD USER WARRANTY POLICY

GJ Handy & Co Ltd reserve the right to change specifications and/or price without notice

Version 2 08-2014

3. Not covered by this warranty

(a) The warranty policy does not cover any depreciation or damages caused by ordinary wear, rusting or

corrosion, lack of correct maintenance or operation, misuse, abuse, lack of transportation or accident.

(b) The warranty policy does not cover any costs necessary for the standard periodic maintenance services

instructed by the operators manual, or service parts replacement which would include oil, filters, tyres,
belts, brake linings, fuses, blades, seals and other service parts unless it can be proven that the item has
evidence of faulty manufacture.

(c) The warranty policy will not cover failure or damage caused as a result of parts or accessories being

modified without the written approval of GJ Handy & Co Ltd.

(d) The warranty policy will not cover the unit if non-genuine parts have been fitted and as a result the unit

has been damaged.

(e) The warranty policy is non-transferable and is only applicable to the original purchaser.

4. Disclaimer

(a) This warranty is only a remedy for product defects. GJ Handy & Co Ltd will never issue a warranty for the

merchantability of a product or its fitness for a particular purpose.

(b) No person is authorised to make any warranties, representations or promises, expressed or implied, on

behalf of GJ Handy & Co Ltd, or to modify the terms conditions or limitation of this warranty policy in any
way.

(c) Neither GJ Handy & Co Ltd nor any company affiliated with GJ Handy & Co Ltd shall be liable in any

event or manner whatsoever for incidental or consequential damages or injuries, including, but not
limited to, loss of crops, loss of profit, out of pocket expenses or profits, rental of substitute equipment or
other commercial losses.

5. General

(a) Most warrantable failures show up within the first few weeks of use. These failures are usually

straightforward and warranty assessment is relatively easy.

(b) Failures relating to cutter decks and belts need careful investigation, as the cause may not always be

straightforward. Look for damage to blades and pulleys especially when the cutter belt or blade boss
have snapped or cracked as this could be due to impact damage.

(c) Customers should always refer to the operator’s instruction manual when any disputed problem arises,

you will find most areas covered within the manual.

19

NOTES

20

•

•

HHAANNDD PPUUSSHH CCYYLLIINNDDEERR

LLAAWWNN MMOOWWEERRSS

•

•

EELLEECCTTRRIICC && PPEETTRROOLL

CCYYLLIINNDDEERR

LLAAWWNN MMOOWWEERRSS

•

•

IINNTTEERRCCHHAANNGGEEAABBLLEE

CCYYLLIINNDDEERR CCAARRTTRRIIDDGGEESS

•

•

EELLEECCTTRRIICC && PPEETTRROOLL RROOTTAARRYY

LLAAWWNN MMOOWWEERRSS

•

•

PPEETTRROOLL RRIIDDEE OONN

LLAAWWNN MMOOWWEERR

•

•

PPEETTRROOLL LLAAWWNN SSCCAARRIIFFIIEERR

AA SSEELLEECCTTIIOONN OOFF QQUUAALLIITTYY PPRROODDUUCCTTSS FFRROOMM OOUURR VVAASSTT RRAANNGGEE

FFIINNDD OOUUTT MMOORREE AATT WWWWWW..WWEEBBBBLLAAWWNNMMOOWWEERRSS..CCOO..UUKK

21

Warranty Registration Form

Please go to www.webblawnmowers.co.uk select registration and complete the registration for your machine.

(Alternatively please fill in this form and return to the address above.)

Owner’s Name: …………………..…………………………………………………………………..................

Address: ………………………………………………………………………………………......................... …………………………… Postcode:………………….. Telephone No.: ……..……………................

Email Address: ……………………...................................... Agent/ Dealer: ……………………........................................ Product: ....................................................... Model: .................................................................. Serial No: ....................................... ............. Engine No:……..................................................... Date of Purchase: .........................................

Date of Delivery: ......................................... (Warranty Commences From Date of Delivery)

Webb Lawnmowers,

Hobley Drive,

Swindon,

SN3 4NS, United Kingdom.

Telephone: [phone]

Fax: [phone]

E-mail: [e-mail]

Webb Lawnmowers

Hobley Drive

Stratton St Margaret

Swindon

Wiltshire

SN3 4NS