Please read & understand this manual, paying particular attention to the safety instructions, before use.
Operator’s Manual & Parts List
07 Dec 2015
193837002
41cm Steel Deck
Hand Push Lawnmower
WER16HP
193836002
41cm Steel Deck
Self Propelled Lawnmower
WER16SP
Contents
Box Contents
Product Diagram
Assembly Guidelines
Before you begin / Starng the engine
Using your mower / Safety ps
Basic Maintenance
Technical Specificaon
Declaraon of Conformity
Parts List & Diagrams
Warranty
For Spares or Support of your Webb product, please contact us:
Tel: 01793 333212
(Mon – Fri 8.30am to 5.00pm)
Email: customerservice@webblawnmowers.co.uk
To view the full range or find out more informaon go to
www.webblawnmowers.co.uk
×1
1.
×1
4.
×1
2.
×1
5.
×2
3.
×4
6.
1. Petrol Engine Mower
4. Rear Grass Catcher
2. Instruction Manual
5. Mulch Plug
3. Quick Release Handles
6. Bolt and Nut Assembly
What you get with your mower
NOT INCL. WER16HP
INSTRUCTION MANUAL
Please read & understand this manual, paying particular attention to the safety instructions, before use.
Operator’s Manual & Parts List
29 Oct 2015
193861001
42cm Self Propelled
Steel Deck Lawnmower
WER42SP
193863001
46cm Self Propelled
High Wheeled
Steel Deck Lawnmower
WER46SPHW
193864001
51cm Self Propelled
High Wheeled
Steel Deck Lawnmower
WER51SPHW
1.
2.
3.
4.
2
3
6
7
8
5
1
4
9
5.
7.
9.
8.
6.
BOX CONTENTS / PRODUCT DIAGRAM
Drive Lever (WER16SP Only)
Brake (OPC) Lever
Fuel Tank Cap
Air Filter & Primer Bulb
Spark Plug
Exhaust
Oil Filter & Dipstick
Height Adjustment Lever
Grass Collection Bag
Remove and ensure you have all the parts
required for assembly (see page 2 for reference)
Parts required:
4 x Bolts
1. LOWER HANDLE BAR ASSEMBLY
3. ATTACHING THE SAFETY (OPC) CABLE
1.
2. Upper Handle Bar Assembly
Spring cord Guide and bolt.
3a
3b
3. Aaching the Transmission Cable
and bolt.
3a.
Pull the brake lever out of the right
side hole, tilt forward and lower towards
the mower.
3b.
Insert the end of the cable into the
hole in the lever and replace the lever
back into hole of the handle.
INSTRUCTION MANUAL
6. LOCATE THE STARTER CORD
6
The starter cord spring maybe located differently depending on the model
1. Lower Handle Bar Assembly
attach lower handle bar bolts.
take the weight of the handle
2. UPPER HANDLE BAR ASSEMBLY
4. ATTACHING THE DRIVE CABLE
5. FIT THE CABLE CLIPS
5. FIT THE CABLE CLIPS
2a 2b
7a
7b
4. Aaching the Drive Cable
4a.
Pull the drive lever out of the
left side hole and lower
towards the mower.
4b.
the mower handle
5. Fit the Cable Clips
Push the cable clips into place.
Parts required:
2 x Quick Release Handle Assemblies
6. Locate the Starter Cord
Pull the stater cord upto the
spring. holding the cord at the
lower side of the spring rotate
the string clockwise around
the spring.
7. Aach the Grass Catcher
7a.
with one hand.
7b.
Lower the Grass catcher
hooks onto bar, left and right.
4a 4b
5
INSTRUCTION MANUAL
The mower is supplied without oil in the
engine. Refer to the B&S engine manual
before starting the engine for the first time.
Firstly, remove the warning label
from under the dipstick, then
remove the dipstick and slowly
pour SAE30 or 10W/30
lawnmower grade engine oil int
the engine via the oil filler (as directed by
thr B&S engine manual).
Replace the dipstick and tighten.
Before you use the mower each
time, check the oil level (fig. 2) and
if necessary top up with SAE30
or 10W/30 oil. To check the oil level,
unscrew the yellow dipstick, wipe
with a rag and replace into the oil
filler (do not screw back in place),
remove the dipstick again and
check the level.
The oil level must be between the
min and max marks on the dipsick
(fig.3). Replace the dipstick and
screw into place.
Petrol is highly flammable so
extreme caution must be taken when
handling it. Always store petrol in
approved containers and you must
ensure that you use fresh petrol that it
less than 4-6 weeks old. Do not mix oil
with petrol.
To put petrol in the fuel tank, firstly
remove the warning label form
under the petrol cap. It’s best to fill
the tank using a clean funnel, but
never fill it completely (fig. 4).
Instead, leave at least 13mm from
the bottom of the filler neck to
allow for expansion. Ensure that
you securely tighten the petrol cap
after filling. (Funnel & fuel not
supplied).
INSTRUCTION MANUAL
WARNING!
The following procedures must be carried out before you start the engine of your lawnmower.
!
STARTING THE ENGINE
Starng the engine
1.
Make sure that your mower is
on a safe, at area (a paved area
or path is ideal - avoid thick wet
grass and gravel surfaces) away
from fuel or fueling area to
make starting safe.
2.
Press the fuel primer bulb
5 times.
3.
Firmly hold the brake handle
with one hand, and then with
your other hand pull the cord
slowly until you feel resistance.
Then pull vigorously with one
positive action (Fig. 7). Guide the
cord back to it’s rest position (do
not release).
4.
To restart a hot engine, refer to
‘Point 3’
5.
To turn off your mower, release
the brake handle.
Fig 5
Fig 7
USING YOUR MOWER
Aach the Grass Collecon Bag
The grass collection bag attaches
easily by lifting the mower’s Rear Flap
with one hand (Fig. 9) and slide the
grass collection bag into position (Fig.
10).
Cung Height Adjustment
For best results adjust the cutting
height of your mower to suit the
mowing conditions. Do not try to
remove too much grass in one pass.
Adjustment of the cutting height is
made centrally. Turn off the mower
and take the weight of the mower
by lifting. Take hold of the cut height
adjustment lever, positioned on the
mower’s right hand rear wheel.
Move the lever outwards to release
it from its locating notch. Move
the lever towards the front of the
machine to increase the cutting height
and towards the rear to reduce the
cutting height. Return the lever to
the locating notch to set the desired
cutting height.
securely into its serrated holder (Fig.
11).
Mowing your Lawn
Start your mower (see: Starting
the engine). Keep hold of the Brake
(OPC) Lever (releasing the Brake
(OPC) Lever will stop the engine to
avoid accidents) (Fig. 12). To power
the mower forward move the Drive
Lever up and forward (Fig. 13). The
mower can be pushed with the drive
disengaged for more precise handling.
After mowing and emptying the Grass
Collection Bag ensure the engine is not
running and turned off.
Cleaning your Mower
Cut grass is damp. Regular cleaning
after each use will ensure better
functioning of the mower and reduce
the risk of corrosion or seizure.
the engine to cool then remove
accumulated grass clippings from and
around the engine with a brush. Clean
the grass collection bag annually with
a brush or gentle spray of water and
allow to dry.
Clean underneath regularly disconnect the spark plug cap and tilt
the mower backwards. Remove cut
grass with a scraper and a brush.
Do not use a pressure washer or hot
water to clean the mower. Dry off the
machine before storing by leaving it
clean surface to prevent corrosion or
seizure.
Storing your Mower
Store your mower in a dry, well-
sparks or heat sources. Disconnect the
spark plug cap. Avoid storing beneath a
tarpaulin or similar cover as it may
cause condensation resulting in
corrosion.
Winter Storage:
Thoroughly clean the mower. Run
the engine outdoors until fuel tank
is empty or empty fuel using a fuel
suction pump. Dispose of discarded
fuel safely and responsibly. Run
the engine until remaining fuel is
consumed.
Remove the spark plug from the
engine. pour a tablespoon of engine
oil into the cylinder. Gently pull the
starter rope several times to distribute
the oil to protect the cylinder over
winter. Replace and tighten the spark
plug.
Transporng your Mower
Ensure the fuel tank is empty. Run
the engine until any remaining fuel is
consumed. Allow the engine to cool.
How to cut for best results
For best results cut your lawn in
alternative directions switching
direction each time you cut. Cut your
lawn at an equal and regular height.
Slightly overlap your cutting lines.
WARNING!
WARNING!
!
!
Turn mower off before
adjusting cutting height lever
Turn mower off before cleaning
Fig 9
Fig10
Fig12 Fig13*
Fig11
*WER16SP Only
INSTRUCTION MANUAL
Before starting your mower
inspect it carefully to ensure that
there are no loose parts and that it
is in good working order.
Be sure of your footing.
Always walk, never run, when
operating the lawnmower.
Keep hands, feet and
clothing away from the
mower’s moving parts and
always wear appropriate footwear
(avoid sandals or open shoes).
Never put your hands or feet
underneath the chassis of the
lawnmower while the engine is
running.
Clear the area to be mowed of any
stones, sticks, wire and debris
before beginning. Always ensure
that you mow a safe distance away
(over 14 metres) from adults,
children and animals.
Always use fresh premium unleaded
petrol that is not more than 4-6 weeks
old. Fill the tank using a funnel, but
never completely. Clean up
any overflow or splashes
before starting.
Do not smoke when filling
the fuel tank, using the
machine,or when petrol is in the
immediate area. Never use or store
the mower near a naked flame.
Turn off the engine and disconnect
the spark plug cap before cleaning,
transporting, or making adjustments.
Never leave the mower unattended.
Never open the fuel filler cap, or fill
the tank, if the engine is still hot
after use. Please ensure that you
securely tighten the petrol cap
after filling.
Mow across the face of slopes,
not up & down, and avoid mowing on
very steep slopes. We recommend
you avoid mowing when it is
raining, after nightfall or in
poor light conditions.
Do not transport the
mower in a vehicle if there
is any petrol in the tank.
Be aware that the machine’s
exhaust area and other parts
of the lawnmower get very
hot during and right after use.
Turn off the engine before
emptying the grass-catcher and
before clearing any grass caught
in the rear flap where the catcher fits.
Store fuel and oil in a cool
well-ventilated place, away
from direct sunlight and gas
cylinders or hot water heater systems
It is recommended that you wear
ear protectors, safety goggles and
safety boots when using the
lawnmower.
All servicing and repair work under
warranty must be carried out by an
Authorised Dealer, otherise the
1+1-Year warrany may be void.
To inspect the underside of your
mower, only tilt the lawnmower
to your right, or back, when standing
behind it (this is the side where the
exhaust is near the ground) otherwise
oil may leak into inappropriate areas
of the engine. Never tilt the lawnmower
when the engine is running.
Do not operate the machine by
pulling it towards you as you risk
pulling it onto your feet. Instead,
always push and walk behind your
lawnmower.
Do not fill the tank, or start
the lawnmower indoors, or in a
poorly ventilated area, as exhaust
gases contain poisonous substances
and petrol fumes are flammable
and dangerous.
Do not alter engine governing
settings or over-rev the engine, as
excessive speed is dangerous and
can reduce engine life.
Holding the blade firmly in one hand, use
a spanner or socket to loosen the blade
screw & rotate anti-clockwise.
Wear appropriate protective gloves to
prevent possible injury when handling
the blade. Disconnect the spark plug cap
and tilt the mower on its side with air
filter and carburettor side uppermost.
Before and after each mowing session,
check that the blade, its attachment
bolts and drive shaft are not damaged
or excessively worn. Never try to
straighten a bent blade. Replace a
damaged, worn or bent blade as soon
as possible. Use only genuine WEBB
parts or those approved by WEBB.
Wear appropriate protective gloves to
prevent possible injury when handling
the blade. Disconnect the spark plug cap
and tilt the mower on its side with air
filter side uppermost.
Check that all components (the blade,
key, blade holder, screws and washers)
are present, clean and in good condition.
Tighten the screws connecting all of
the components. Make a final visual
check that all parts are present and
aligned before tightening the fixing
bolt very firmly with a wrench while
holding the blade firmly in one hand
(NB wear suitable gloves).
Rotate clockwise
Check the correct alignment and
matching of pads with the blade.
The blade must be positioned
precisely on its stand.
Position the blade on its support with
the cooling fins facing the engine.
For best mowing results, have the edges
sharpened and the blade balanced at
least once a year by a specialist service
dealer or agent.
Excessive vibration when mowing is a
good indication of a problem with the
cutting system.
Check the spark plug initially after the
first five hours of mower use.
Thereafter, maintenance of the spark
plug should take place every 25 hours.
Remove the spark plug cap (Fig.15)
using a rotary motion and then remove
the spark plug with the wrench provided
(Fig.16).
If the spark plug is worn or damaged,
replace with a new spark plug of the
same or suitable type for the engine.
If in doubt, contact your point of
purchase or local dealer.
Alwasy refer to your B&S manual.
Clean off any carbon deposits using a
copper brush and check the electrode
gap with a feeler gauge (the gap should be
≈ 0.7 mm). Replace and tighten the
serviced spark plug and replace the cap.
The spark plug cap must be
removed before any aempt
is made to remove the blade
INSTRUCTION MANUAL
MAX
MIN
Air Filter
will reduce the performance and
life of the engine while making it
harder to start. Regular checks
are therefore essential, especially
when using the mower in dusty
conditions. Check and clean the air
often if the engine is used in a dusty
environment.
cartridge. Clean the cartridge in a
small bowl of warm water containing
a few drops of washing-up liquid
until it is perfectly clean and free
from all traces of grease and dust.
water and then squeeze gently to
remove most of the water. Let it air
dry until it is completely dry.
Clean the cover and inside of the air
Apply a uniform layer of oil to the
brush (you can use clean engine oil
lid, ensuring that each component
is in place and properly installed. If
very dirty, replace it using a genuine
part.
in. Remove the dipstick and check
the oil level holding the dipstick
horizontal.
The oil level should be between the
minimum and maximum oil level
marks on the dipstick (Fig.20). Add
oil if necessary and repeat the above
checking process. Running the
engine without oil or with too little
oil can cause serious engine damage.
Note: Dispose of used engine oil carefully,
responsibly and in accordance with local or
national regulations
Changing the oil
of mower use. Thereafter, change
the oil after every 25 hours use
or at least once a year. Leave the
engine running outdoors for several
minutes to warm the oil and make it
Remove the spark plug cap and
unscrew the oil level dipstick. Use a
suitable oil suction pump and follow
with new oil.
WARNING!
!
Parts of the engine will become very
hot and can cause severe burns.
WARNING!
The above advice is provided as an aid, please follow the instructions provided in your B&S engine manual, when maintaining your engine.
WARNING!
Do not twist the foam cartridge to
clean it as this could cause damage.
If your mower is not serviced
correctly, you could reduce your
mower’s ability to operate and void
warranty.
MAX
MIN
Fig17
Fig19
Fig18
Fig20
Checking the oil level
level surface. Unscrew the oil level
dipstick (Fig.19) and wipe dry.
Insert the dipstick until it reaches
!
BASIC MAINTENANCE
TECHNICAL SPECIFICATION
ca
b
Consistent with our policy of continuous
improvement, WEBB reserves the right
of any of its products without notice or
obligation.
Therefore, please treat the text
and images in this manual as being for
illustrative purposes only. They may
in no case serve as a basis for any
legal claim.
WER16HP WER16SP
Maximum Operating Speed
Cutting Width 41cm / 16”
2800 rpm
41cm / 16”
Adjustable Cutting Heights 5 5
Cutting Heights 25-70cm 25-70cm
Grass Collection Capacity 40 L 40 L
Noise Level 96 dB 96 dB
Chassis
Heavy Duty
Steel
Heavy Duty
Steel
Dimensions (cm)
a = 130. b =
110. c = 53
a = 165. b =
110. c = 65
Function
Collection
Mulching
Collection
2800 rpm
INSTRUCTION MANUAL
Problem Likely cause Suggested remedy
E ngine d oe s n ot
start
Out, or almost out, of fuel Fill tank with min unleaded petrol
Spark plug depleted Replace with a suitable new spark plug
Spark plug dirty Clean or replace with a new spark plug
Spark plug not connected Press
rmly on the terminal cover
Flooded engine Remove Spark Plug, clean with appropriate cloth and refit
Old petrol in the tank Drain stale fuel and replace with new min unleaded petrol
Water in the fuel tank Contact an authorised dealer
Engine stops often
Blocked fuel supply Ensure the fuel line is not pinched or blocked
Fuel cap is not venting You may need to slightly loosen the fuel cap
Wrong type of fuel Drain petrol tank and ll with new min unleaded petrol
Engine loses power
Dirty air cleaner lter Clean or replace with a new air- lter
Incorrect height adjustment Raise the mower’s cutting height lever
Blocked fuel cap vent holes Ensure the 3 holes in the fuel tank cap are clear
Mower vibrates too
much
Loose cutting blade Check and tighten bolts and nuts
Bent or broken disc/blades Replace disc or blades
Excessive grass/dirt build-up Clean and ensure underside clear of build up
Disc or blades worn/damaged Replace blades
Poor cutting
catching
Catcher not
tted correctly Reattach carefully and also check for damage
Incorrect cutting height set Adjust the cutting height
Blocked grass catcher vents Clear and clean the vents
FAST TROUBLE SHOOTING
EC DECLARATION OF CONFORMITY
We Handy Distribuon Ltd - SN3 5HY (Importer) declare that the product:
Designaon: 125cc Petrol Lawnmower
Model(s): WER16HP / WER16SP
Type/Serial No. As per rang label on machine
Complies with the following direcves:
2006/42/EC- Machinery Direcve
2004/108/EC- Electro-Magnec Compability Direcve
2000/14/EC amended by 2005/88/EC- Noise Emission in the Environment by Equipment for use
Outdoors Direcve.
The conformity assessment procedure followed was in accordance with
EN 836/A
3:2004
ZEK01.2-08.2008
EN ISO 14982:2009
EN ISO 3744:1995
ISO 11094:1991
Nofied Body:
TÜV SÜD Product Service GmbH
Addresses:
Ridlerstrasse 65-80339 München (Germany)
Westendstrasse 65-80686 München (Germany)
No. 88 Heng Tong Road, Shanghai 200070, (P.R. China)
Measured Sound Power Level: 90.8dB(A)
Guaranteed Sound Power Level: 96dB(A)
Authorised signatory and technical file holder
Date: 30/07/2014
Signature:
Name: Mr Simon Belcher
Posion: Managing Director
Company: Handy Distribuon Ltd
Address:
Murdock Rd, Swindon, Wiltshire, SN3 5HY.
NOTES
WER16HP - Blade Assembly
Item No Part No Description Qty
1 QG112-38 Blade Adaptor 1
2 QG113-39 Blade 1
3 WE70040070000 Blade Washer 1
4 WE113-71 Hex Flange Bolt 50mm 1
Item No Part No Description Qty
1 B&S 450E Petrol Engine 1
2 QG112-10 Self-Tapping Screw ST6.3x18 2
3 QG112-11 Large Washer 6x18x1.6 2
4 WE113-42 Lock Nut M6/8.8 3
5 QG112-12 Rear Discharge Base A 2
6 QG112-13 Rear Discharge Base B 1
7 QG112-14 Bolt M6x16 3
8 WE113-12 Lock Nut M8/8.8 6
9 QG112-15 Left Rear Bracket 1
10 WE113-34 Square Neck Bolt M8x15/8.8 6
11 WE113-42 Lock Nut M6/8.8 4
12 QG112-16 Bolt M6x12 4
13 QG112-17 Height Adjustment Rod 1
14 WE114-21 Hex Self-Tapping Screws 3/8 16x1ST 3
15 WE70740930590 Deck 1
16 QG112-20 Height Adjustment Board 1
17 QG112-21 Right Rear Bracket 1
18 WE113-25 "O" Ring 11.2x2.65 1
19 WE113-26 Hose Connector Inlet 1
20 WE113-27 Hose Connector Nut M12x1.25 1
21 WE113-28 Cable Stopper 1
WER16HP - Deck Assembly
Item No Part No Description Qty
1 WE20620280000 Wheel Trim (Grey) 2
2 WE113-52 Lock Nut M8 2
3
WE113-51
Wheel Bearing 4
4 WE20640230000 Front Wheel 2
5 QG112-24 Front Axle 1
6 WE113-67 R Pin 1.5x25 1
WER16HP - Front Axle
Item No Part No Description Qty
1 WE20620080059 Wheel Trim (Grey) 2
2 WE113-52 Lock Nut M8 2
3 WE113-51 Wheel Bearing 4
4 WE20880301000 Rear Wheel 2
5 WE20270010059 Height Adjustment Handle 1
6 QG112-27 Rear Axle 1
7 WE113-67 R Pin 1.5x25 1
WER16HP - Rear Axle
Item No Part No Description Qty
1 WE113-1 Foam Handle Cover 1
2 WE113-2 Brake Lever 1
3 WE104-5 Bolt M6x30 2
4 WE113-10 Plastic Stopper 1
5 WE113-7 Brake Cable Assembly Plate 1
6 WE113-42 Lock Nut M6/8.8 2
7 WE113-4 Top Handle 1
8 WE113-5 Rope Guide 1
9 WE113-6 Cap Nut M6/8.8 1
10 WE118-1 Brake Cable 1
11 WE116-1 Hex Nut M8 4
12 WE60250220000 Pin 2
13 WE113-17 4
14 WE113-52 Lock Nut M8 2
15 WE20040050059 Triangle Knob 2
16 WE104-16 Square Neck Bolt M8x32/8.8 2
17 QG112-5 Square Neck Bolt M8x20/8.8 2
18 QG112-6 Lower Handle 2
19 WE20240020000 Cable Clip 1
20 WE20040010059 Thin Knob 2
21 WE20580030059 Quick Fold Handle 2
22 WE70220020000 Quick Fold Bolt 2
23 WE60200040000 Quick Fold Nut Housing 2
Flat Washer ￠8.4X￠16X1.6
WER16HP - Handle Assembly
Item No Part No Description Qty
1 WE113-65 Lock Washer 2
2 QG112-29 Rear Discharge Cover 1
3 WE113-64 Rear Discharge Cover Spring 1
4 QG112-30 Rear Discharge Cover Shaft 1
5 QG112-31 Grass Collector Breather 1
6 QG112-32 Grass Collector Board 1
7 QG112-33 Grass Collector Top 1
8 QG112-34 Gasket 4
9 WE117-3 Self-Tapping Screw ST6.3x14 4
10 QG112-36 Grass Collector Frame 1
11 WE20070070011 Grass Collector Bag (Webb) 1
WER16HP - Grass Collector
Item No Part No Description Qty
1 WE114-19 Chassis Bushing 2
2 WE117-19 Belt Cover 1
3 WE60060390000 Hex Flange Bolt M8x25 1
4 WE60060180000 Hex Flange Bolt M8x30 2
5 WE117-20 Blade Adapter 1
6 QG113-89 Blade 1
7 WE113-70 Blade Washer 1
8 WE113-71 Hex Flange Bolt 50mm 1
WER16SP - Blade Assembly
Item No Part No Description Qty
1 B&S Engine 1
2 QG112-10 Self-Tapping Screw ST6.3x18 2
3 QG 11 2 - 11 Large Washer 6x18x1.6 2
4 WE113-42 Lock Nut M6/8.8 3
5 QG112-12 Rear Discharge Base A 2
6 QG112-13 Rear Discharge Base B 1
7 QG112-14 Bolt M6x16 3
8 WE113-12 Lock Nut M8/8.8 6
9 QG112-15 Left Rear Bracket 1
10 WE113-34 Square Neck Bolt M8x15/8.8 6
11 WE113-42 Lock Nut M6/8.8 6
12 QG112-16 Bolt M6x12 6
13 QG112-17 Height Adjustment Rod 1
14 WE117-3 Self-Tapping Screw ST6.3x14 5
15 WE70740950130 Deck 1
16 QG112-20 Height Adjustment Board 1
17 QG112-21 Right Rear Bracket 1
18 WE113-25 "O" Ring 11.2x2.65 1
19 WE113-26 Hose Connector Inlet 1
20 WE113-27 Hose Connector Nut M12x1.25 1
21 WE113-28 Cable Stopper 1
22 WE117-5 Pressure Plate 2
23 WE117-23 Mulch Plug 1
WER16SP - Deck Assembly
Item No Part No Description Qty
1 WE20620280000 Wheel Trim (Grey) 2
2 WE113-52 Lock Nut M8 2
3
WE113-51
Wheel Bearing 4
4 WE20640230000 Front Wheel 2
5 QG112-24 Front Axle 1
6 WE113-67 R Pin 1.5x25 1
WER16SP - Front Axle
Item No Part No Description Qty
1 WE113-67 R Pin 1.5x25 1
2 WE117-6 Drive Cog Left 1
3 WE60290080000 Drive Pin 2
4 WE117-8 Self-propelled Washer 4
5 W E 11 4 -11 Spring Washer 12 6
6 WE117-10 Drive Cog Right 1
7 W E 11 7 -11 Rear Axle 1
8 WE20620080059 Wheel Trim (Grey) 2
9 WE113-52 Lock Nut M8 2
10 WE113-51 Wheel Bearing 4
11 WE20880301000 Rear Wheel 2
12 WE117-13 Inner Wheel Cover 2
13 WE20270010059 Height Adjustment Handle 1
14 WE113-55 Rear Axle Sleeve 2
15 WE117-16 Self-propelled Spring 1
16 WE117-17 rear drive assy. 1
17 WE117-18 Drive V Belt 1
18 WE70050270000 Brake spring 1
WER16SP - Rear Axle
Item No Part No Description Qty
1 WE113-1 Foam Handle Cover 1
2 WE113-2 Brake Lever 1
3 WE117-2 Self-propelled Lever 1
4 WE113-4 Top Handle 1
5 WE113-5 Rope Guide 1
6 WE113-6 Cap Nut M6/8.8 2
7 WE113-7 Brake Cable Assembly Plate 1
8 WE104-5 Bolt M6x30 2
9 WE113-52 Lock Nut M8 2
10 WE118-1 Brake Cable 1
11 WE60200040000 Pin 2
12 WE20580030059 Quick Fold Handle 2
13 WE70220020000 Quick Fold Bolt 2
14 WE113-17 6
15 WE116-1 Hex Nut M8 6
16 WE70520290130 Lower Handle 2
17 WE20240020000 Cable Clip 1
18 WE20040010059 Thin Knob 2
19 QG112-5 Square Neck Bolt M8x20/8.8 2
20 WE104-16 Square Neck Bolt M8x32/8.8 2
21 WE20040050059 Triangle Knob 2
22 WE104-19 Plug 2
23 WE70780090000
Self-propelled Cable
1
24 WE113-10 Plastic Stopper 1
Flat Washer ￠8.4X￠16X1.6
WER16SP - Handle Assembly
Item No Part No Description Qty
1 WE113-65 Lock Washer 6 2
2 WE20380080060 Rear Discharge Cover 1
3 WE113-64 Rear Discharge Cover Spring 1
4 QG112-30 Rear Discharge Cover Shaft 1
5 QG112-31 Grass Collector Breather 1
6 QG112-32 Grass Collector Board 1
7 QG112-33 Grass Collector Top 1
8 QG112-34 Gasket 4
9 WE117-3 Self-Tapping Screw ST6.3x14 4
10 QG112-36 Grass Collector Frame 1
11 WE20070070011 Grass Collector Bag (Webb) 1
WER16SP - Grass Collector
This Service Book is provided with your Webb, to help you look after your purchase to our recommendations and enable you
to take advantage of the 2 year conditional manufacturer domestic warranty*.
* Commercial/Professional & Hire users receive a 90 day warranty
Present this service book to your authorised Webb repair dealer, whenever a service or a warranty appraisal is required.
The booklet is applicable to the following products, in the UK only:
Ride On Lawn Tractors
Petrol & Electric Cylinder Lawnmowers
Petrol Rotary Lawnmowers
Petrol Hand Held Range
Please register your machine using the following pages or at www.webblawnmowers.co.uk. By registering your machine, you
agree to maintain the machine in accordance with the service schedules specied in this manual and services duly recorded.
You may be asked to produce this booklet as proof of servicing in the event of a claim. Proof of purchase should also be kept
as a reference.
Ensure you have the following information available from your machine product label. The two examples below can be found
on your machine:
1
3
4
2
1. Model Number
2. Serial & Product Number
Please complete using BLOCK CAPITALS.
Sections marked* must be completed to validate Warranty.
Cylinder Mowers Only
3. Serial Number
4. Model Number
INSTRUCTION MANUAL
1. Users Statement of Warranty
Each new machine is warranted against defective material or assembly of material under normal usage. The warranty applies
to the original purchaser, is not transferable and covers faulty parts and the labour involved in replacing and repairing those
parts, which are of original manufacture.
2. Period of Warranty
2 year conditional warranty from the original date of sale to the rst domestic user.
90 days from the original date of sale to the professional/commercial or for hire user.
Engine warranty as per the engine manufacturer’s warranty, which will be supplied with the machine.
90 days from the original date of sale for Replacement Spare Parts
All machines’ must be serviced within the rst 14 months from the original date of purchase, to qualify for a second year
parts & labour warranty, details of the service must be recorded in the service record within this manual.
A reduced warranty period of 90 days applies to those items which are subject to normal wear and tear and in normal use,
will need replacement or adjustment.
These items are chargeable after 90 days of ownership.
Filters
Tyres / Wheels
Drive chains and belts
Brake & clutch friction components
Control cable & starter cords
Fluids & lubricants
Spark plugs
Blades (Lawnmowers & Brushcutters)
Cutter bars (Hedgecutters)
Drive & clutch cable surfaces
Nylon Lines (Line Trimmers)
Carburettor cleaning
Bearings
Bushes
Electric cable
Grass collectors
3. Not covered by this warranty
(a) The warranty policy does not cover any depreciation or damages caused by ordinary wear, rusting or corrosion, lack of
correct maintenance or operation, misuse, abuse, lack of transportation or accident.
(b) The warranty policy does not cover any costs necessary for the standard periodic maintenance services instructed by the
operators manual, or service parts replacement which would include oil, lters, tyres, belts, brake linings, fuses, blades, seals
and other service parts unless it can be proven that the item has evidence of faulty manufacture.
(c) The warranty policy will not cover failure or damage caused as a result of parts or accessories being modied without the
written approval of GJ Handy & Co Ltd.
(d) The warranty policy will not cover the unit if non-genuine parts have been tted and as a result damage has occurred to
the unit.
(e) The warranty policy is non-transferable and is only applicable to the original purchaser.
4. Disclaimer
(a) This warranty is only a remedy for defect of products. GJ Handy & Co Ltd will never warranty in terms of the
merchantability or the tness for a particular purpose.
(b) No person is authorised to make any warranties, representations or promises, expressed or implied, on behalf of GJ
Handy & Co Ltd, or to modify the terms conditions or limitation of this warranty policy in any way.
(c) Neither GJ Handy & Co Ltd nor any company afliated with GJ Handy & Co Ltd shall be liable in any event or manner
whatsoever for incidental or consequential damages or injuries, including, but not limited to, loss of crops, loss of prot, out
of pocket expenses or prots, rental of substitute equipment or other commercial losses.
SERVICE BOOK
5. General
(a) Most warrantable failures show up within the rst few weeks of use. These failures are usually straightforward and
warranty assessment is relatively easy.
(b) Failures relating to cutter decks and belts need careful investigation, as the cause may not always be straightforward.
Look for damage to blades and pulleys especially when the cutter belt or blade boss have snapped or cracked as this could be
due to impact damage.
(c) Customers should always refer to the operator/instruction manual when any disputed problem arises, you will nd most
areas covered within the manual.
Protecting your machine
Maintenance
Regular maintenance of your Webb machine is essential to ensure it operates, safely, efciently and therefore reducing the
environmental impact.
It is the owner’s responsibility to ensure that their Webb machine is maintained at specic intervals. Any approved Webb
service dealer can undertake a service, which are specialised in our products and will be aware of your particular machine
and any technical updates which will save valuable time & money.
If you are using your machine in dry, dusty or high temperatures, you will need to service the machine more regularly.
Fuel
Due to ongoing efforts by fuel companies to reduce emissions, unleaded petrol will oxidize & deteriorate in storage overtime,
leaving residue from detergent components.
Fuel deterioration problems may occur when petrol is stored for over 30 days. If you are planning to store fuel for over
30 days, we recommend you add Handy Parts Sure-Start fuel stabilizer to fresh fuel after purchasing. Sure-Start cannot
reconstitute stale fuel.
Storage
When storing your machine for an extended period, we do recommend that you follow the instructions of engine instruction
manual.
Always store the fuel in a clean, approved and sealed container. If the container is steel, ensure it is not corroded.
If the container is not lled to its recommended capacity, air can accelerate fuel deterioration.
Always store fuel away from direct sunlight, in a dark, cool environment.
INSTRUCTION MANUAL
Your servicing Webb approved dealer will stamp & date the below relevant sections, when the correct service actions have
been completed.
PLEASE ENSURE THE SERVICE BOOK IS AVAILABLE FOR THE DEALER, DURING SERVICE WORK.
1st Service
This must be stamped by an approved service dealer to
qualify for a free second year warranty.
24 Months
Date Date
36 Months
12 Months
Date
SERVICE BOOK
48 Months
Date
Date
Date
Date
Date
Date
Date
Date
72 Months
96 Months
120 Months
60 Months
84 Months
108 Months
132 Months
INSTRUCTION MANUAL
*House Number *House Name
*Address 1
*Address 2
*Town
*County
*Postcode
Home Tel Mobile Tel
Email
If you have registered online, this form is not necessary.
PLEASE POST THIS COPY TO THE ADDRESS OVERLEAF
*Title *Forename *Surname
Age 18 to 25 26 to 35 36 to 45 46 to 60 61 to 80 81 & over
*Usage Domestic Use Commercial/Professional/Hire Use
Personal Information (* Compulsory)
*Model No:
*Product No:
*Serial No:
*Date of Purchase:
Product Information (* Compulsory)
Webb Lawnmowers privacy commitment to machine owners: Thank you for completing this form. The information supplied, helps us to improve the
products & services we provide, including information that we believe is relevant to your and/or your machine. We value your trust by giving us this
information about yourself and we are committed to protecting your privacy. From time to time Webb, its associated companies, authorised dealers or third
parties working on our behalf may wish to contact you regarding our products, services, offers, technical improvements or just opinions, which may be used
for marketing, research or analysis purposes.
If you DO NOT wish to be contacted by either of the following methods, please tick the relevant box POST TELEPHONE
If you would like us to contact you be Email, please tick this box
You may give Webb Lawnmowers notice in writing at any time that you no longer wish to receive direct marketing communications
*Dealer Stamp (Complete Address)
*Dealer Name
*Dealer Address
*Date of Purchase
*Selling Retailer (If dealer stamp not available)
WARRANTY REGISTRATION
Webb Lawnmowers
Murdock Road
Dorcan
Swindon
Wiltshire
SN3 5HY
Loading...