Page 1
Installation Instructions
ThermoCall TC4
Entry/Advanced
Page 2
Thermo Call TC4
# 67769A
965 082 AMP
1
2
3
4
# 24990A
# 98393A
Page 3
Thermo Call TC4
ThermoCall TC4 Entry
5
Please refer to the corresponding heater
documentation for all other heater
integrations.
123456
789101112
sw
Page 4
Thermo Call TC4
Please refer to the corresponding heater
documentation for all other heater
integrations.
ThermoCall TC4 Advanced
6
sw
123456
789101112
Page 5
Improper installation or repair of Webasto heating and cooling systems can
cause fire or the leakage of deadly carbon monoxide leading to serious injury
or death.
To install and repair Webasto heating and cooling systems you need to have
completed a Webasto training course and have the appropriate technical
documentation, special tools and special equipment.
Only genuine Webasto parts may be used. See also Webasto air and water
heaters accessories catalogue.
NEVER try to install or repair Webasto heating or cooling systems if you have
not completed a Webasto training course, you do not have the necessary
technical skills and you do not have the technical documentation, tools and
equipment available to ensure that you can complete the installation and
repair work properly.
ALWAYS carefully follow Webasto installation and repair instructions and
heed all WARNINGS.
Webasto rejects any liability for problems and damage caused by the system being installed by untrained personnel.
Page 6
ThermoCall TC4
Table of Contents
Installation Instructions ........................................................................................................................................ 1
General information .........................................................................................................................................................1
Certification .....................................................................................................................................................................1
Scope of Delivery Entry ....................................................................................................................................................1
Scope of Delivery Advanced .............................................................................................................................................2
Adapting wiring harness ..................................................................................................................................................2
ThermoCall TC4 Entry: .................................................................................................................................................2
ThermoCall TC4 Advanced: .........................................................................................................................................2
Legend ............................................................................................................................................................................2
SIM card ..........................................................................................................................................................................3
Installation ........................................................................................................................................................... 4
Installing GSM module .....................................................................................................................................................4
Installing GSM antenna ....................................................................................................................................................4
Installing button with indicator lamp ............................................................................................................................4
Connection ........................................................................................................................................................... 5
Connector assignment of GSM module ...........................................................................................................................5
Connection of an alarm system installed in the vehicle (Advanced) ...................................................................................6
Connection of an external temperature sensor (Advanced) ..............................................................................................6
Connection to heater .......................................................................................................................................................7
Thermo Top Evo or Thermo Top E/C ............................................................................................................................7
Thermo Top Evo or Thermo Top E/C with MultiControl (Advanced) .............................................................................7
Thermo Top Evo or Thermo Top E/C with Telestart T91/T100 HTM (Advanced) ...........................................................7
Summer/winter connection (only Advanced, only for Thermo Top E/C) ............................................................................8
Initial start-up ..................................................................................................................................................................8
Technical data ...................................................................................................................................................... 9
Drawing of installation location for GSM module in vehicle ............................................................................... 10
Page 7
Installation Instructions
3
4
5
1
2
ThermoCall TC4
General information
With ThermoCall TC4 the following
Webasto heaters can be operated
with a mobile or landline phone:
Water heaters:
-Thermo Top E/C
-Thermo Top Evo
-Thermo Pro 50 Eco
-Thermo Pro 90
-Thermo 120/150 STD
Air heaters:
-Air Top 2000 STC
-Air Top Evo 40
-Air Top Evo 55
Detailed information can be found in
er operating instructions.
the heat
The function cannot be guaranteed
conjunction with OE heaters.
in
Please turn over these installation
structions to the customer
in
together with the operating
instructions.
Certification
The CE marking and the E-marking
are located on the adhesive label on
the module.
Scope of Delivery Entry
1. GSM module ThermoCall TC4
2. Entry wiring harness
3. GSM antenna
4. Button with indicator lamp
5. Self-tapping screws
and (not shown):
-Quick Start Guide
-CD with operating and installation instructions
1
Page 8
ThermoCall TC4
3
4
5
1
2
Scope of Delivery Advanced
0
1. GSM module ThermoCall TC4
2. Advanced wiring harness
3. GSM antenna
4. Button with indicator lamp
5. Self-tapping screws
and (not shown):
-Quick Start Guide
-CD with operating and installation instructions
2
Adapting wiring harness
The included wiring harness must be
adjusted with corresponding
"pinning into" the existing
installation situation (heater
selection).
ThermoCall TC4 Entry:
Strip the tied-back wires at the
ter connector, connect the
hea
required wires as shown in the
illustrations 1 to 4 and illustration 5
and then insulate and tie back the
wire ends that are not required.
ThermoCall TC4 Advanced:
Strip the tied-back wires at both
tors for the heater and
connec
control element, connect the
required wires as shown in the
illustrations 1 to 4 and illustration 6
and then insulate and tie back the
wire ends that are not required.
Legend
To illustrations 1 to 6.
br brown
ge yellow
gr grey
rt red
sw black
vi violet
--- not in use
Thermo Top E/C
Thermo Top Evo
Page 9
ThermoCall TC4
SIM card
A SIM card not included in the
delivery scope is required to operate
the unit.
Both 1.8 V and 3 V SIM cards of a
k operator, which supports
networ
the GSM 900/1800 mobile
communications standard, can be
used.
Always observe any information of
pective network operator
the res
when operating the SIM card. No
warranty can be given for the SIM
card used. The function should be
checked separately in individual
cases.
Before inserting the SIM card, the
code must be changed to 1234
PIN
with a mobile phone. Information on
this topic is contained in the
respective operating instructions of
the mobile phone.
All data which may be present on
he SIM card will be deleted when
t
commissioning the GSM module.
The SIM card is inserted under the
liding cover on the top of the GSM
s
module with the angled side
opposite the hinge and with the chip
side facing downward.
Only insert or remove the SIM card in
the deenerg
The range is dependent on the
resp
result from the operation of a SIM
card. Information on this topic and
on roaming charges abroad and in
areas close to the border (due to
network overlapping) can be
obtained from the respective
network operator. No liability can be
accepted for any costs arising.
ised state.
ective network operator. Costs
3
Page 10
ThermoCall TC4
91011
Installation
Installing GSM module
The GSM module must be installed in
the passenger compartment.
-Determine the installation location in
assenger compartment (under
the p
the instrument panel, when retrofitting preferably near the MultiControl
the radio receiver)
or
-Fasten the GSM module with self-tapping screws (ensure sufficient clearance for the connection of the wiring
and the antenna)
harness
-Watch vehicle parts located behind
he module when mounting it with
t
the self-tapping screws! Contacts/
plug connections must face downwards.
NOTE
Note down the installation
ation of the GSM module
loc
on the last page of these
installation instructions, e.g.
for replacing SIM card!
4
Installing GSM antenna
The antenna must be installed on
the front or rear window. However,
never in the tinted area or under the
heating wires of the window heater
or wires of the window antenna.
-Clean the window thoroughly with a
eaning cloth
cl
-Pull the protective film off the anten-
na and glue on the antenna (maintain
minimum distance of 30 mm from
a
metal parts)
-Route the antenna cable to the GSM
dule (never shorten or kink) and
mo
connect to the module
Installing button with indicator lamp
NOTE
-The supplied push button
must be insta
-Follow initial start-up procedure.
-Install push button in view of
the dri
-Drill an 8 mm diameter hole in a dummy switch or another suitable location easily accessible to the driver
oordinate the installation location
(c
with the vehicle owner if necessary)
-Mount the push button in the 8 mm
a. hole
di
-Route the push button wiring harness
to the 12-pi
ule and connect them (blue wire on
9, green on Pin 10 and red on Pin
Pin
11)
lled.
ver.
n connector on the mod-
Page 11
ThermoCall TC4
Connection
Connector assignment of GSM module
Socket Function Remarks Entry Advanced
1 12 - 24 V (+30)
2 Earth = 0
3 Output of parking heater only for Thermo Top E/C
4 additional analogue output, 12-24 V positive * for 2nd installed heater with
5 Earth output for summer function (fan only) only for Thermo Top E/C
6 W bus communication with parking heater or
7 not in use (optional Input 1 for alarm system) +12 V
8 Input 2 (for MultiControl/Telestart) only for Thermo Top E/C
9 Earth for push button including indicator lamp (blue wire)
10 ON/OFF for push button including indicator lamp (green
11 Output for indicator lamp in push button (red wire)
12 not in use
*:The connection may vary depending on the installed 2nd heater. Information on the integration is contained in the
respective heater installation instructions.
MultiControl/ Telestart
wire)
analogue control
only for Thermo Top Evo
5
Page 12
ThermoCall TC4
Connection of an alarm
system installed in
(Advanced)
The vehicle owner receives a text
message when the alarm system is
triggered.
Insert the wire in Pin 7 of the 12-pin
connector and connect it to the output
of the alarm system (must be a +12 V
signal).
To define which text message
ontent the ThermoCall TC4 is to use
c
to inform you, send the following
text message command to the
ThermoCall TC4 following initial
start-up: 1234IBANK:"Entry
command". The entry command
can, for example, be Alarm.
The alarm can be sent to up to 5
numbers. To define which
phone
phone numbers are to be used, send
the following text message
command to the ThermoCall
TC4:1234NBANK:XXX:YYY:ZZZ:
VVV:WWW
XXX:YYY:ZZZ:VVV:WWW = phone
rs to be entered by the user,
numbe
e.g.:
+436641234567:+4369912345678
: etc.
6
the vehicle
Connection of an external temperature sensor (Advanced)
This is required for measuring the
temperature outside the ThermoCall
TC4 (e.g. for cargo areas) and for
using the temperature alarm
function.
Required material:
-W bu s temperature sensor 9023181A
not required in combination with
(
Telestart T100 HTM)
-Y-adapter 9001505A (only required if
control element is connected after
a
the ThermoCall TC4)
-See the Webasto Accessories Cata-
logue for any required extensions.
Carry out the connection as shown in
he following drawing and illustrations
t
on the inner cover pages.
To use the temperature alarm, the
hone numbers to be notified must
p
be reported to the ThermoCall TC4.
To define the phone numbers, the
following text message command
must be sent to the ThermoCall TC4:
1234NBANK:XXX:YYY:ZZZ:VVV:
WWW
XXX:YYY:ZZZ:VVV:WWW = phone
ers to be entered by the user,
numb
e.g.:
+436641234567:+4369912345678
: etc.
For details, see operating
structions.
in
Page 13
Advanced:
Not used
Connector
of heater
wiring
Entry
Connector
of heater
wiring
harness
To GSM
module
To GSM
module
To MultiControl
To GSM
module
Connector of
heater wiring
harness
To Y-adapter
Connector
of heater
wiring
harness
To GSM
module
Connection to heater
Thermo Top Evo or Thermo Top E/C
-Connect wiring harness to GSM module.
-Connect the 4-pin connector of the
ter wiring harness to the 4-pin
hea
GSM module wiring harness
Thermo Top Evo or Thermo Top E/C with MultiControl (Advanced)
-Connect wiring harness to GSM module.
-Connect the 4-pin connector of the
ter wiring harness to the 4-pin
hea
GSM module wiring harness
-Connect the 4-pin GSM module connector to the MultiControl
ThermoCall TC4
Thermo Top Evo or Thermo Top E/C
with Telestart T91/T100 HTM
vanced)
(Ad
-Connect wiring harness to GSM module.
-Connect the 4-pin connector of the
ter wiring harness to the 4-pin
hea
GSM module wiring harness
-Connect 4-pin GSM module connector to the Y-adapter of the Telestart
7
Page 14
ThermoCall TC4
Summer/winter connection
(only Advanced,
Thermo Top E/C)
-The summer/winter wire is not included in the delivery scope and must be
red separately
orde
-Connect the violet wire to the violet
re of the heater wiring harness us-
wi
ing a connector
-Plug into a free slot of the 4-pin connector of the heater wiring harness
8
only for
Initial start-up
-Connect the 12-pin connector of the
GSM module wiring harness to the
module
-After applying voltage, the indicator
amp flashes 2x per second.
l
-After about 60 seconds, the indicator
amp flashes 1x per second.
l
NOTE
Depending on the dial-in time
f the SIM card, it can take a
o
up to 5 minutes until the
system is finally ready for
operation
-As soon as operational readiness is
chieved, program the ThermoCall
a
TC4 and put it into operation according to the operating instructions.
-To query the firmware version
send the text message command
ERSION" to the ThermoCall TC4
"V
NOTE
Check that the indicator lamp
i
n the button is functioning
correctly.
Operation of the
ThermoCa
permitted with a fully
functional indicator lamp.
-Indicator lamp flashes to show the
ystem is ready for operation
s
ll TC4 is only
-Follow the heater initial start-up procedure.
Page 15
Technical data
Values Entry Advanced
Rated voltage 12 V DC
Rated voltage 12 / 24 V DC
Bias current consumption 0.005 A
Current consumption during data transfer 0.040 A
Max. output current 1.00 A
Max. input voltage 35 V
Switching voltage for inputs +5.5 V
Permissible ambient temperature -40 °C to +85 °C
Permissible storage temperature -40 °C to +85 °C
Dimensions (LxWxH) 95x55 (75) x30 mm
Weight 100 g
Protection type IP42
Material PBT
ThermoCall TC4
9
Page 16
ThermoCall TC4
Drawing of installation location for GSM module in vehicle
Note or sketch the installation location of the GSM module in the following field for possible service cases.
10
Page 17
In multilingual versions the German language is binding.
The telephone number of each country can be found in th
the respective Webasto representative of your country.
e Webasto service center leaflet or the website of
Webasto Thermo & Comfort SE
Postfach 1410
82199 Gilching
Germany
Visitors’ address:
Friedrichshafener Str. 9
82205 Gilching
Germany
Internet: www.webasto.com
Technical Extranet: http://dealers.webasto.com
Ident-Nr. 9032843A • 06/15 •Errors and omissions excepted • Printed in Germany • © Webasto Thermo & Comfort SE, 2015
Loading...