Webasto Thermo Top, Tele Thermo Top T Operating Instructions

Ident-Nr. 9000825A 3/0008

Operating Instructions

Telestart T70
Thermo Top and Thermo Top T
Tele Thermo Top T

General Information

Maintenance and Safety Information

Dear Webasto Customer !

We assume that the workshop / service center that carried out the installion explained to
you the operation and principle of functioning of your new heater to your complete
satisfaction. With these operating instructions we would like to provide you with an
overview of the use of the Thermo Top, Thermo Top T and Tele Thermo Top T heaters as
well as the hand-held transmitter Telestart T70.

Within the scope of the StVZO (Road Traffic Licensing Act) "General Design Approvals"

laid down by the Federal Office for Motor Traffic exist for the water heaters.

The installation of the units must be carried out in accordance with the enclosed
installation instructions. The installation must be checked in accordance with the Legal
Provisions for Installation. For details refer to the installation instructions.

The year of the initial operation must be durably marked on the heater's nameplate by
removing the non-applicable years.

Thermo Top

n

n

n

at filling stations and tank farms.

in locations where flammable vapours or dust may
accumulate (e.g. in the vicinity of fuel-, coal-, sawdust or
grain depots).

in enclosed spaces (e.g. garages). This should also be
considered when pre-setting heater operating times or
using the Telestart remote control.

nnexposed to temperatures greater than 120°C (storage

temperature). Exposure to such temperatures may cause
damage to the electronic components.

operated without a minimum level of 20% of good quality
antifreeze in the water of the heating circuit.

The heater must be switched :off

Danger of explosions

and asphyxiation

The heater must benot

D

!

Webasto Thermosysteme International GmbH

Postfach 80 - D-82132 Stockdorf - Hotline [phone]
Hotfax (0395) 55 92-353 - http://www.webasto.de

Setting the Operating Time

Returning to the Default Setting

Checking the Batteries

Press the ON or OFF button.

or

Batteries LED Action

okay after 1 sec.

lights up for

0.5 sec.
in red (heating) or in
green (ventilation)

low charge after 1 sec. flashes

in orange for 3 sec.

- Warm up batteries to above 0°C

- Replace batteries at the next
opportunity

discharged after 1 sec.

lights up for
5 sec. in orange

- Warm up batteries to above 0°C

- Replace batteries

Press the OFF button to call up the next operating time.
To store the setting:

- do not actuate any button for 10 seconds, or

- actuate the ON button.

Press the ON and OFF buttons simultaneously for approx. 10
seconds until the LED extinguishes.

Default setting: heating mode, 30 minutes.

Programming Telestart Transmitters

Checking the Mode

Mode setting

Depress the ON and OFF buttons simultaneously twice within
one second.

The newly selected mode (heating or ventilation) will be set in
the receiver the next time a signal is transmitted.

Upon the second actuation, the LED will change its
colour and illuminate until the buttons are released.

Simultaneously depress and hold down the ON and OFF buttons.

LED illuminates:
in : heating mode
in : ventilating mode

LED extinguishes:

- when the buttons are released, or

- after 10 seconds

red
green

2x

1. Place batteries into the battery compartment of the transmitter.

2. Remove fuse 1A (black) from the heater's fuse holder (voltage interruption).

3. Wait at least 5 seconds.

4. Replace fuse in heater's fuse holder and within 5 seconds press the OFF button
on the transmitter for at least 1 second.

5. "Learning" is completed.

A second or third hand-held transmitter can be programmed in the same manner.

min. 1 sec.

OFF

1A 1A

25A

15A

1A

25A

15A

1A

min. 5 sec. max. 5 sec.

Digital Timer with 3 Time Settings

Instant heat Reverse Program selection Forward

Symbol for
setting/
viewing
the time

Program
number
display

Clock button

Heater operation
indicator

Display illumination

1

2
3

SET

Note:
Be sure to take
into account the
switching from
summer time to
winter time (and
vice versa).

!

General

Switching the
heater on

Setting the
time of the day

Viewing
the time

Programming
heater starting
time

Erasing pro­grammed times

Selecting
preset starting
time

Switching the
heater off

SET

SET

SET

SET

The start of the heating operation can be precisely preset anywhere
between "1 minute" up to "24 hours". Three starts may be
programmed only one of which, however, can be activated.

Manually: by pressing the "instant heating" button
Automatically: by programming the heater starting time
The program number is shown on the display and the display is
illuminated.

Manually: by pressing the "instant heating" button
Automatically: after the programmed operating time has elapsed
The display field is no longer illuminated.

Press the "Clock" button and subsequently "Forward" or
"Reverse" .

Press the "Clock" button

Press the button
Within 10 sec. press the "Forward" or "Reverse" button until the
desired time for the start of the heating operation is shown on the
display.
If a different program number is required, press the button.

Briefly press the button.

Press the button within 10 sec. periods until the program number
associated with the desired preset time is displayed