WEATHER GUARD 8931-3 User Manual
ASSEMBL Y AND INSTALLA TION INSTRUCTIONS
IMPORTANT
BEFORE YOU BEGIN
Read these instructions and
warnings completely before
installation.
Slide Out Rack - Model 8931
Rack Assembly
1/4-20x1-1/4" Bolt
BOLT KITS
Bolt Kit #709 is provided with your
Rack. Check this bolt kit to be sure
the following parts are included:
Quan. Description
8 1/4" Flat Washer
4 1/4-20 x 1/2" Screw, phillips
4 1/4-20 x 1-1/4" Bolt, hex hd.
4 1/4-20 Nylon Lock Nut
Bolt Kit #32-0345 is provided with
your Rack. Check this bolt kit to be
sure the following parts are in
cluded:
Quan. Description
1 1/4-20 Plusnut®
1 Plusnut® Tool
1 1/4-20 x 1-1/4" Blk Ox Bolt
1 1/4" Lock Washer
Flat Washer
Nylon Lock Nut
TOOLS REQUIRED
• Screwdriver, phillips
• 7/16" Open or Box End
Wrench (2)
• Electric Drill with 5/16" Drill Bit
Rev. A 4/95 Part No. 24-8931
INSTALLATION
INSTRUCTIONS
1. Place Rack Assembly in position
and pull lower slide all the way out. Remove lower slide (See
Drawer Removal) and mark mounting hole locations.
CAUTION
Prior to drilling, so as not to
cut or puncture fuel tanks,
fuel lines, brake lines, electric wires, etc., check under
vehicle for locations.
CAUTION
To keep debris out of your eyes
when checking the underside of the
vehicle, or when drilling, always
wear protective eyewear.
3. Fasten unit in position.
NOTE - A 1/4-20 Plusnut®, Plusnut®
Tool, 1/4-20 x 1-1/4" Black Oxide Bolt
and 1/4" Lock Washer are provided for
use in areas where standard fasteners
can't be used, such as heat shields
and floor supports. See Plusnut® installation instructions.
NOTE - If stacking, use four 1/4-20 x
1/2" screws (provided) instead of 1/420 x 1-1/4" bolts. Model 8940 Acces-
sory Mounting Strap Kit is required
if stacking units.
INSTALLATION PROCEDURE
USING PLUSNUT® BLIND
FASTENERS
CAUTION
Prior to drilling, so as not to
cut or puncture fuel tanks, fuel
lines, brake lines, electric
wires, etc., check under vehicle for locations.
DRAWER REMOVAL (above)
2. Remove rack assembly and
drill marks with a 5/16" drill bit. Replace
the rack.
W ARNING
All floor mounting bolts near
the gas tank area should be
installed from the underside
of the vehicle, to guard
against the gas tank being
punctured in the event of a
collision. This would mean
not using Plusnuts® in this
area.
1. Pull drawer all the way open, then
push back to align stop with lance stop.
2. Push lance stop in with screwdriver
as shown, until lance stop clears the
stop on the drawer guide.
3. Repeat on the other side and remove drawer.
4. To install drawer, pry out lance stop
(approx. 1/4") and push drawer into
slide until it stops.
Use 7/16" wrench to tighten black hex
bolt until Plusnut® fastener is fully
seated. When setting black hex bolt, it
will start out hard. As the Plusnut®
“bulbs” out it will get easier, until the
Plusnut® bottoms out or sets. Make
sure the Plusnut® and Plusnut® Tool
do not turn during installation.
-NOTICE-
Any modification or unintended use of this product shall immediately void all manufacturers warranties.
Manufacturer disclaims all liability for injuries to persons or property resulting from any modification to, or
unintended use of this product.
If you have any questions, please give us a call. Call Toll Free 1-800-456-7865
Weather Guard® products are protected by one or more of the following patents or trademarks:
U.S. - 842268, 1661625, 1663369; Canada - 282725; U.K. - 1400720; other patents pending.
KNAACK MANUFACTURING COMPANY
420 E. TERRA COTTA AVENUE - CRYSTAL LAKE, ILLINOIS, 60014 - 815-459-6020
©1992 Knaack Manufacturing Company
Loading...