WEATHER GUARD 8908-3 User Manual
INSTALLATION MANUAL
PARTS CABINET
VAN STORAGE SOLUTIONS
Danger of explosion. Do not use this product for stor ing or transporting ammables, exp losives, hazardous materials, or hazardous waste, such as
containers of gasoline, solvents, gun powder, dynamite, propane tanks, acetylene tanks and cutting torches. Failure to heed this warning will result
in death or serious injury.
This product is only intended and safe for use in storing and transporting small tools, equipment and other similar materials. These instructions are
to be followed using the parts and fasteners supplied for proper installation. Any modications or improper installation of this product will create a
hazardous condition that could result in death, serious personal injury and/or property damage.
All oor mounting bolts near the fuel tank area should be installed from the underside of the vehicle, to guard against the fuel tank being punctured in
the event of a collision. This would mean not using Blind Fasteners in this area. Holes in this area should be 5/16". Ensure ample space in roof ribs
and sidewall ribs for mounting screws so as not to puncture exterior roof or wall.
Do not install this product where it could interfere with deployment of air bags. Failure to comply could result in death or serious body injury.
FOR THE WAY YOU WORK™
ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS
BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT.
Models 8906-3 • 8908-3 • 8909-3 • 8918-3
WWW.WEATHERGUARD.COM
DANGER
WARNING
CAUTION
Prior to drilling, so as not to cut electric wires, fuel lines, brake lines, etc., check behind and underneath drilling and mounting locations. To keep debris
out of your eyes when checking the underside of the vehicle, or when drilling, always wear protective eye wear. Failure to heed this warning will result
in death or serious injury.
– NOTICE –
Any modication or unintended use of this product shall immediately void all manufacturers warranties. Manufacturer disclaims all liability for injuries
to persons or property resulting from any modication to, or unintended use of this product.
INSTALLATION TIME
Approximate installation time: 12 minutes per unit (0.2 hours) depending on van equipment installation experience.
TOOLS REQUIRED
• 7/16" Open or Box End Wrench (2)
• Pencil or Marker
• Electric Drill with 5/16" Drill Bit
Bolt Kit #3522 is provided with your product. Check this bolt kit to be sure
the following parts are included:
NOTE: Depending on your application you may end up with extra
hardware after installation is complete.
BOLT KIT
DESCRIPTION
BOLT KIT
#3522 QTY.
*24-0063*
1/4-20 Nylon Lock Nut 10
1/4-20 x 1/2" Hex Head Bolt 10
1
Part No. 24-0063 Rev B 11/11 (ECN 5026)
Figure 2. Flat Shelf Installation
1/4-20 Nylon
Lock Nut
5/16" Hole
1/4-20 x 1/2"
Hex Hd. Bolt
INSTALLATION INSTRUCTIONS (3" SHELF)
NOTE: Model 8918-3 has three brackets, use third
as a center support, not to be bolted to bottom of
unit. Install bracket before bolting unit to shelf.
STEP 1: For installation on a 3" shelf, use two Mounting
Brackets with models 8906-3/8908-3/8909-3 and three
brackets for model 8918-3.
STEP 2: Bolt Mounting Brackets to cabinet bottom (see
Figure 1).
STEP 3: Position unit aligning mounting bracket holes
with van shelf holes and bolt unit to shelf.
INSTALLATION INSTRUCTIONS (1" SHELF)
STEP 1. Mounting brackets are not used on a 1" shelf.
Invert shelf, as shown in Figure 2.
1/4-20 x 1/2"
Hex Hd. Bolt
Mounting Bracket
1/4-20 Nylon
Lock Nut
1/4-20 Nylon
Lock Nut
Figure 1.
1/4-20 x 1/2"
Hex Hd. Bolt
STEP 2. Set unit in position and mark four holes. Remove
unit and drill holes.
STEP 3. Bolt unit to shelf.
2
Loading...