WEATHER GUARD 8867-3-01 User Manual

WORKTOP MODEL 8867

INSTALLATION MANUAL

ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT.

WARNING – NOTICE –

These instructions are to be followed using the parts and fasteners
supplied for proper installation. Any modifications or improper
installation of this product will create a hazardous condition that
can cause property damage, serious personal injury or death.

Approximate Assembly and Installation Time:

2

. (.3 hours) depending on van equipment

0 min

installation experience.

PARTS

Item Qty. Description

A 1

1 B

1 NOTE: The unit(s) this work top is to be

mounted on, must be the correct width or
properly spaced to accept the mounting
method.

Place the Work Top in position and mark the
center point of the bolt holes that will require
fastening.

NOTE: Mark
since an off-center Blind Fastener makes
installation difficult.

Remove work top and drill where marked
with 1/8" drill bit for pilot holes. Redrill
holes to enlarge them, using a 13/32"
drill bit. Install Blind Fasteners. (See
INSTALLATION INSTRUCTIONS
FOR BLIND

center of bolt hole carefully

FASTENERS on page 2).

Any modification or unintended use of this product shall immediately
void all manufacturers warranties. Manufacturer disclaims all liability
for injuries to persons or property resulting from any modification
to, or unintended use of this product.

TOOLS REQUIRED

• Electric Drill

Work Top

olt Kit #32-0101

• Drill Bits: 13/32", 1/8"

• Open End Wrenches: 7/16", 9/16"

A

Attach Work Top using four (4) 1/4-20 x 3/4"
Hex Head Bolts and 1/4" Lock Washers.

INSTALLATION IS NOW COMPLETE.

PAGE 1IF YOU HAVE ANY QUESTI ONS, PLEASE CONTACT U S TOLL-FREE AT 1.800.4 56.7865

Part No. 24-0244 REV. B ECN 5305 04/13

BOLT KIT #32-0101 NOTE: Depending on your application you may end up with extra hardware after installation is complete.

4 1/4-20 Blind Fasteners

4 1/4" Lock Washers

4 1/4-20 x 3/4" Hex Head Bolts

CAUTION

To keep debris out of your eyes when drilling,
always wear protective eyewear.

Place a drop of oil on the black oxide bolt before
assembling as shown on right. Place the Blind
Fastener in the hole and use a 7/16" wrench to
tighten black hex bolt until the Blind Fastener is
fully seated. When setting black hex bolt, it will
start out hard. As the Blind Fastener “bulbs” out
it will get easier, until it bottoms out or sets. Make
sure the Blind Fastener and Installation Tool do
not turn during installation.

1 Blind Fastener Installation Tool

1 1/4-20 x 2-1/4" Hex Head Black Bolt

INSTALLATION INSTRUCTIONS FOR BLIND FASTENERS

7/16” Wrench

(Or 7/16”

Socket)

Black Oxide Bolt

Flat Washer

9/16” Wrench

Installation Tool

Blind Fastener

KNAACK LLC LIMITED WARRANTY

This LIMITED WARRANTY is made by Knaack //&. 420 E. Terra Cotta Ave., Crystal Lake, Illinois to the original retail purchaser of KNAACK
Products.

KNAACK LLC WARRANTS THAT KNAACK PRODUCTS WILL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP FOR A PERIOD OF
THREE (3) YEARS FROM DATE OF PURCHASE BY THE ORIGINAL RETAIL PURCHASER.

If, before the expiration of the Warranty period, purchaser discovers that the KNAACK Product fails to fulfill the Warranty, purchaser shall contact
Knaack LLC to make arrangements for an inspection of the product. If Knaack LLC determines a defect exists, Knaack LLC shall, at its option and
expense, repair or replace any defective part. All Warranty repairs shall be made by an authorized KNAACK Product dealer or Knaack LLC
approved service company.

This Warranty shall not apply if the KNAACK Product has been subjected to misuse, abnormal service or handling, improper
alterations made by anyone other than a KNAACK Product dealer or a Knaack LLC approved service company.

THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED.

KNAACK LLC. SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF ANY BREACH OF THIS
WARRANTY. NOR SHALL THE DAMAGES EXCEED THE RETURN AMOUNT OF THE PURCHASE PRICE PAID BY THE ORIGINAL
PURCHASER.

This Warranty is in lieu of all Warranties express or implied. The terms of this Warranty shall not be modified by any party, their successors or assigns.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

maintenance, or

®

PAGE 2IF YOU HAVE ANY QUESTI ONS, PLEASE CONTACT U S TOLL-FREE AT 1.800.4 56.7865

Part No. 24-0244 REV. B ECN 5305 04/13