WEATHER GUARD 88052 User Manual

INSTALLATION INSTRUCTIONS

V an Window Screens

IMPORTANT BEFORE YOU BEGIN

Read these instructions and warnings completely

before installation.

WARNING

This product can reduce the driver’s ability to clearly see
roadways, vehicular or pedestrian traffic and other objects
through the rear and side windows of the vehicle, which
can cause an accident. Extra precautions should be taken
when driving a vehicle with this product. Make all adjust­ments necessary to ensure maximum visibility, including
but not limited to, changing mirror and seating positions.
State and local laws may prohibit obstruction of windows
in a moving vehicle.

Van Type Rear Door Rear Door Side Door Side Door Rear Side
Hinged Hatch Sliding Hinged Window

FORD

'92 Model Year & Newer-Full size 88022 88023 88021
'91 Model Year & Older-Full size 88010 88010 88010
'98 Model Year & Older Windstar 88024 88025
'99 Model Year & Newer Windstar 88029 88030

CHEVROLET

'96 Model Year & Older G-Classic 88010 88010 88011
'96 Model Year & Newer GMT 600 88028 88026 88027
Astro 88014 88013
'98 Model Year & Newer Venture 88033 88031 88032

GMC

'96 Model Year & Older Vandura 88010 88010 88011
'96 Model Year & Newer Savana 88028 88026 88027
Safari 88014 88013

DODGE

'94 Model Year & Newer Ram 88010 88010 88010
'94 Model Year & Older Caravan 88016 88017 88015

PLYMOUTH

'94 Model Year & Older Voyager 88016 88017 88015

BOLT KITS Each Van Window Screen unit is shipped with matching bolt kit(s) which include:

88013 88023 88011* 88031* 88010*
88015 88025 88016* 88032* 88024 88014* 88026

MODELS 88017 88029 88021 88027 DESCRIPTION

88033 88030 88022 88028

BOLT KIT 32-8813 32-8813 32-8810 32-8810 32-8820
QUANTITY 10 20 12 24 16 1/4-14x3/4" Self Drilling Screw

10 20 12 24 16 1/4" Flat Washer

*- Includes two bolt kits

Rev. E 3/99 Part No. 24-8811

*
*

PARTS LIST TOOLS REQUIRED

MODELS DESCRIPTION

88013 88015 88033 88010 88011 88027
88017 88023 88014 88016 88028
88024 88025 88021 88031
88029 88030 88022 88026 88032

Qty. 1 2 Screens

• Drill with 5/16" Hex Driver Bit or
5/16" Nut Driver

• Hacksaw or Wire Cutters

• File

• Pliers

NOTE
These Wire Window Screens
are designed to fit in cargo
areas of cargo vans. If your
vehicle has interior window
trim, it may require removal.

INSTALLATION

INSTRUCTIONS

1. Align the Screen over the window

frame and note areas where the
screen may need trimming. Areas that
may need trimming or bending are the
Tabs and Latch. If you have window
latches, open the latch to it's highest
point and replace the screen to deter­mine removal points. If trimming is re­quired, be sure to file down any sharp
edges after cutting.

CAUTION

Screen

Tab

Figure 1.

1/4" Flat Washer

1/4-14x3/4" Self
Drilling Screw

1/4" Flat
Washer

Latch Area

To keep debris out of your
eyes when trimming screen
tabs or using self-drilling
Tek screws, always wear
protective eyewear.

2. Install the screen after proper

alignment.

NOTE - If tab removal was neces­sary, the screen can still be fas­tened by placing the screws to the
inside of the outer framing as
shown in Figure 2.

Figure 2.

- NOTICE -

Any modification or unintended use of this product shall immediately void all manufacturers warranties.
Manufacturer disclaims all liability for injuries to persons or property resulting from any modification to, or
unintended use of this product.

If you have any questions, please give us a call. Call Toll Free 1-800-456-7865

KNAACK MANUFACTURING COMPANY

420 E. TERRA COTTA AVENUE - CRYSTAL LAKE, ILLINOIS, USA 60014 - 815-459-6020

©1999 Knaack Manufacturing Company