Read and understand all instructions and warnings before operating or using this product.
This product is only intended and only safe for transporting ladders. It is the responsibility of the user to secure these
materials to the rack before transporting.
Ladders must be secured per ANSI standard A142.2-1990 paragraph 8.4.4. Ladder damage will occur from road shock
and vehicle vibration if the ladder is not properly secured to the ladder rack. Bouncing and side to side motion of an
improperly secured ladder will cause wear and weaken the ladder. Using a damaged ladder could lead to structural collapse resulting in serious injury or death. Place ladder in a raised position before transporting. Driving with rack in lowered
position may cause serious injury or damage to vehicle, ladder, rack or persons.
Any modification or unintended use of this product shall immediately void all manufacturers warranties. Manufacturer disclaims all liability for injuries to persons or property resulting from any modification to, or unintended use of this product.
Never load your rack to exceed the safe capacity of your vehicle. Heavy loads when carried high can dangerously alter the
center of gravity.
Loads should be approximately centered front to rear. Failure to do this will cause damage to the vehicle roof. Long loads
that extend out the rear of the vehicle will prevent the rear hatch from fully opening and cause damage if attempted.
WARNING
–ATTENTION–
–NOTICE–
CAUTION
ASSEMBLY INSTRUCTIONS
MODEL 2501 EZ-GLIDE™SYSTEM
WARNING LIGHT HOLDER
TOOLS REQUIRED
• 1/2" Open or Box End Wrench
• 3/8" Drive Socket (1/2")
• 3/8" Drive Ratchet
• 3/8" & 1/2" Drill Bits
• Electric Drill
• Tape Measure
PARTS LIST
• Warning Light Holder
1 Mounting Kit:
2 5/16-18 x 2-3/4" Hex Hd. Bolt
2 5/16-18 Nylon Lock Nut
4 5/16" Flat Washer
HARDWARE KIT
SEE PAGE 2
Check this kit to be sure the following parts are included.
Approximate assembly and Installation time:
30 min. per unit (1/2 hr.) depending on van equipment and installer experience.
IMPORTANT BEFORE YOU BEGIN
Read these instructions and warnings completely before installation.
1
Part No. 24-0105 REV. C ECN 5315 05/13
STEP 1
This Warranty is in lieu of all Warranties express or implied. The terms of this Warranty shall not be modified by any party, their successors or assigns. This Warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
Place the Warning Light Holder (A) on top of the desired Cross-Member (B). Mark the
location of the two mounting holes. Drill two 3/8" dia. through holes the cross-member.
Next measure, mark and drill one 1/2" dia. through hole centered between the
mounting holes. The center hole is for the wires from the light to pass through.
(2) 5/16-18 x 2-3/4"
Hex Hd. Bolt
STEP 2
Attach the Warning Light Holder to the Cross-Member
with the 5/16-18 x 2-3/4" Fasteners.
(4) 5/16"
Flat Washer
(A)
(B)
(2) 5/16-18
Nylon Lock Nut
NO REPLACEMENT PARTS AVAILABLE FOR THIS MODEL
This LIMITED WARRANTY is made by Knaack LLC, 420 E. Terra Cotta Ave., Crystal Lake, Illinois to the original retail purchaser of KNAACK® or WEATHER
GUARD® products.
KNAACK LLC WARRANTS THAT KNAACK OR WEATHER GUARD PRODUCTS WILL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP FOR A
PERIOD OF TWO (2) YEARS FROM DATE OF PURCHASE BY THE ORIGINAL RETAIL PURCHASER.
If, before the
Knaack
replace any defective part.
This Warranty shall not apply if the KNAACK or WEATHER GUARD product has been subjected to misuse, abnormal service or handling, impr
alterations
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUD-ING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY
DISCLAIMED. KNAACK LLC SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF ANY BREACH OF THIS
WARRANTY. NOR SHALL THE DAMAGES EXCEED THE RETURN AMOUNT OF THE PURCHASE PRICE PAID BY THE ORIGINAL PURCHASER.
Product fits based on vehicle design available at the revision date. Vehicle manufacturers may change specs after the revision date, so if you have a
vehicle produced with a model year date after the revision date, please contact
If you have any questions, please call our customer service department at 1-800-456-7865. WEATHER GUARD Products are protected
more of the following patents: U.S. 5145087, 5308126, 4509787, 4573731, 4618083, D-346355, D-346994, D-353574; Canada 1218968, 1224230,
1235100 and; U.K. 2233036. Other patents pending.
expiration of the Warranty period, purchaser discovers that the KNAACK or WEATHER GUARD product fails to fulfill the Warranty, purchaser shall contact
to make arrangements
LLC
made by anyone
for an inspection of the product. If Knaack
All Warranty repairs shall be made by an authorized KNAACK Product dealer or Knaack LLC approved service company.
other than a KNAACK or WEATHER GUARD Product dealer or a K
420 E. Terra Cotta Ave, Crystal Lake, IL 60014, 815-459-6020, info@knaack.com
LIMITED WARRANTY
LLC
KNAACK LLC
©2002 Knaack LLC
ines a defect exists, Knaack
determ
your distributor or Knaack LLC to verify fitting of product to vehicle.
naack
LLC
approved s
shall, at its
LLC
ervice company.
option and expens
oper maintenance, or
e, repair or
by one or
2
Part No. 24-0105 REV. C ECN 5315 05/13