Wayne-Dalton 3750-372, 3014, 3651-372, 3012 User Manual
Photoelectric Safety Sensors
Installation Instructions
and Owner’s Manual
Wayne-Dalton Corp.
P.O. Box 67 Mt. Hope, OH 44660
(888) 827-3667
www.wayne-dalton.com
Quantum™/Classicdrive™ models: 3012, 3014, 3016, 3018, 3212, 3213, 3214, 3312, 3313, 3314, 3316, 3412, 3414, 3512, 3514.
DoorMaster™ models: BDOR-2000 & BIRW-2000
idrive™ models: 3660-372, 3661-372, 3662-372, 3760-372, 3751-372.
Opener Models:
Torsion idrive™ models: 3651-372, 3750-372.
WIRES ARE
PRE-ATTACHED
Photoelectric Sensors Hardware: 297218
(2) 5/16 x 1-1/2” Lag Screws
(2) 1” Flat Head Nails
Photoelectric Sensors
(1) Sender w/Wire: 260600
(1) Receiver w/Wire: 260597
(2) 1/4-20 x 1/2” Carriage Bolts, Washers & Nuts
(2) Wall Mounting Brackets
(2) “U” Brackets
(1) Power Cord Clip (adhesive back)
(1) Jumper
Important Notice!
DOOR OPENER WILL NOT OPERATE PROPERLY UNTIL PHOTOELECTRIC
SENSORS ARE INSTALLED AND PROPERLY ADJUSTED! DO NOT OPERATE
DOOR OPENER UNTIL IT IS FULLY INSTALLED, ADJUSTED AND YOU ARE
INSTRUCTED TO DO SO!
© Copyright 2003 Wayne-Dalton Corp. New 9/4/2003
Part No: 306736
Table of Contents
Important Safety Instructions For Installation And Use 2.
Bracket Installation 3.
Wiring Installation “Quantum™/Classicdrive™” 4.
Wiring Installation “DoorMaster™” 4.
Wiring Installation “idrive™” 5.
Wiring Installation “Torsion idrive™” 5.
Photoelectric Safety Sensor Alignment 6.
Photoelectric Obstruction Sensing Test 6.
Important Safety Instructions 7.
Warranty 7.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Customer Service Number 7.
THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT YOU TO POTENTIAL
PERSONAL INJURY HAZARDS. OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS
SYMBOL TO AVOID POSSIBLE INJURY OR DEATH.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○
WARNING DISCONNECT ALL POWER FROM GARAGE DOOR OPENER BEFORE SERVICING
OR INSTALLING ACCESSORY PRODUCTS.
IMPORTANT SAFETY INSTRUCTIONS FOR
INSTALLATION AND USE
READ AND FOLLOW ALL
INSTALLATION INSTRUCTIONS.
DO NOT USE SENSITIVITY
ADJUSTMENT TO COMPENSATE
FOR A POORLY OPERATING DOOR.
THIS WILL INTERFERE WITH THE
PROPER OPERATION OF THE
SAFETY REVERSE MECHANISM.
DO NOT CONNECT OPENER TO
ELECTRICAL OUTLET UNTIL
INSTRUCTED TO DO SO.
AFTER INSTALLING OPENER,
THE DOOR MUST REVERSE
WHEN IT CONTACTS A 1 INCH
HIGH SOLID TEST OBJECT ON
THE FLOOR.
OPEN DOOR MUST NOT CLOSE
AND CLOSING DOOR MUST
OPEN IF PHOTOELECTRIC
SYSTEM IS OBSTRUCTED BY
6”X HIGH OBJECT, USING TEST
PROCEDURE DESCRIBED IN
STEP 4.
INSTALLATION AND WIRING MUST
COMPLY WITH LOCAL BUILDING
AND ELECTRICAL CODES.
CONNECT THE POWER CORD TO A
PROPERLY GROUNDED OUTLET.
DO NOT REMOVE ROUND GROUND
PIN FROM POWER CORD.
DO NOT WEAR RINGS, WATCHES
OR LOOSE CLOTHING WHEN
INSTALLING OR SERVICING A
GARAGE DOOR SYSTEM. USE A
STURDY, NONMETALLIC STEP
LADDER AND WEAR EYE
PROTECTION.
2
Step 1: Photoelectric Safety Sensor Bracket Installation
WARNING
GARAGE DOOR OPENER BEFORE SERVICING OR
INSTALLING ACCESSORIES OR PHOTOELECTRIC
SAFETY SENSORS. FOR ALL OPENERS, UNPLUG 120 V
AC POWER CORD FROM RECEPTACLE. FOR
DOORMASTER, ALSO UNPLUG TELEPHONE CORD TYPE
COMMUNICATIONS CABLE.
DISCONNECT ALL POWER TO
“U” BRACKETS
Select a mounting position, no more than 5 inches above the
floor to center line of wall mounting bracket. The sending and
receiving units should be mounted inside the door opening to
minimize any interference by the sun. However, the sensors
should be mounted as close to the door track or inside edge of
the door as possible to offer maximum entrapment protection.
It is very important that both wall brackets be mounted at the
same height for proper alignment.
The brackets may be temporarily mounted to the jamb with a 1”
flat head nail (provided) using the small hole above the slot.
Using two 5/16 x 1-1/2” lag screws (provided), permanently
mount the wall mounting brackets to both door jambs. In some
installations it may be necessary to attach a wooden spacer to
the wall to achieve the required clearance.
Attach the “U” brackets to the wall brackets with a
1/4-20 carriage bolt, washer and nut (provided). Insert
the bolt from the inside of the “U” bracket and hand tighten only
at this time.
NUT
WASHER
(1) 5/16 X 1-1/2”
LAG SCREW
(1)1/4-20 X 1/2”
CARRIAGE BOLT
TAB HOLES
TOP & BOTTOM
WALL MOUNTING
BRACKETS
NAIL
5”
Identify which side of the garage door opening (if any) is “likely”
to be exposed to sunlight. Since sunlight may affect photoelectric
sensors, you should mount the sending unit (not the receiving
unit) on the side of the door opening exposed most to the sun.
NOTE: If wires must be lengthened or spliced into prewired
installation, use wire nuts or suitable connectors.
Attach the sending and receiving units to the “U” brackets by
inserting their tabs into the respective holes.
3
TABS
TOP & BOTTOM
RECEIVING UNIT
SENDING
UNIT
(NO LED)
LED ALIGNMENT
LIGHT
Loading...