Wayne Dalton 0002119 User Manual

Z-WAVE LIGHT KIT INSTALLATION

FOR TORSION I-DRIVE

Installation Instructions

This insert is to be used in conjunction with the main installaton instructions and owner’s manual.
This insert is for Z-Wave I-Drive TorqueMaster® Pro Operator Only!

GARAGE DOORS & OPENERS

P.O. Box 67 Mt. Hope, OH 44660

© 2008 Wayne-Dalton Corp. Part No. 33xxxx New 9/22/2008

www.wayne-dalton.com

Tools Needed:

Step Ladder

Phillips Screw Driver

Select a grounding type receptacle on either
the ceiling or wall. If one is not available, have
one installed by a qualified electrician.

IMPORTANT! DOOR MUST CLEAR LIGHT
FIXTURE WHEN THE DOOR IS IN THE OPEN
POSITION.

Identify a mounting location for the light fixture
that’s in close proximity to the receptacle, and
within reaching distance of the power cord.
Fasten the mounting bracket to a stud, in the
desired location using (2) #10 x 1-1/2” deep
thread screws. Align the two metal tabs on the
mounting bracket. Hold the light fixture flush
against the mounting bracket using (1) #8 x

0.375” screw as shown. Place the hole plug
into the screw hole in the light fixture.

NOTE: For temperature protection, the hole
plug must be in place prior to using the light
fixture.

WARNING

TO AVOID ELECTRICAL SHOCK/FIRE,
DO NOT CHANGE THE POWER CORD
PLUG IN ANY WAY.

IMPORTANT! THE POWER CORD HAS A
GROUNDING TYPE PLUG WITH A THIRD
(GROUNDIING) PIN. THIS PLUG WILL ONLY FIT
INTO A GROUNDING TYPE OUTLET. IF THE
PLUG DOES NOT FIT INTO YOUR OUTLET,
CONTACT A QUALIFIED ELECTRICIAN TO
INSTALL THE PROPER GROUNDING TYPE
OUTLET. DO NOT ALTER THE PLUG IN ANY
WAY.

Plug the female end of the power cord into the
inlet connect of the light fixture. Now, plug the
other end of the power cord into the nearest
grounding type receptacle. As soon as power is
applied to the light fixture it should blink one
time. Use cable clips and #6 x 7/8” wood
screws to secure the power cord.

Screw a 15W Type-A bulb or 19W Compact
Fluorescent (maximum) light bulb into light
socket and snap diffuser into light fixture.

NOTE: When assembling diffuser, make sure
all three snap tabs are aligned and fully
snapped into the three mating slots of the
light fixture.

Turn receptacle power back on at fuse/breaker
box. The light should blink one time when the
power is turned back on.

IMPORTANT: FOR REPLACEMENT BULBS USE
ONLY 19W MAX COMPACT FLUORESCENT
BULBS OR USE ONLY 15W MAX TYPE-A
BULBS FOR THE LIGHT.

Top portion of Light

Fixture

Light Fixture

Phillips Pan Head

(ITW Fastex 354-310102-00-2099)

Plug into nearest outlet

Mounting Bracket

(P/N 293294)

#8 x 0.375”

Screw

Hole Plug-Snap In

(P/N 311122-6)

#6 x 7/8” Wood

Screws

Wire Clips

(2) #10 x 1-1/2” Deep Thread

Screws (P/N 279995)

Inlet Connector

Pg 1

Programming the Z-Wave Light Kit

Programming the Z-Wave Light Kit to the i-Drive TorqueMaster
Pro.

If your Z-Wave Light Kit is included with the opener, it should
already be programmed to the opener. Otherwise, follow the
instructions below.

IMPORTANT: ERASE ANY EXISTING PROGRAMMING ON
Z-WAVE LIGHT KIT

1. Press and hold the DELETE button on the unplugged
Wireless Gateway until the 3 LEDs turn on, then let go of the
button.

2. Press the red button on the Z-Wave Light Kit and
observe the LEDs on the Wireless Gateway flash. All network
programming, if any, has now been deleted from the Z-Wave
Light Kit. Press the red button again to turn off the light. If the
button is held in, the Z-Wave Light Kit may flash its light on
and off repeatedly. This is okay.

PROGRAM Z-WAVE LIGHT KIT TO PRIMARY CONTROLLER

1. Insure the Z-Wave Light Kit light is off.

2. Press the Scene 1 button on the Wireless Gateway and
observe that the LED lights up. Continue holding the button
down until the LED turns off and the turns back on again.

3. While the Scene 1 button is still being pressed, press
the red button on the Z-Wave Light Kit, while observing the
LED for Scene 1. If the LED flashes, the Z-Wave Light Kit has
been successfully programmed to Scene 1 of the Wireless
Gateway.

4. Release the button on the Wireless Gateway.

5. Note: If the programming was unsuccessful, try moving
the Wireless Gateway closer to the Z-Wave Light Kit or change
orientation.

COPY PRIMARY CONTROLLER PROGRAM TO THE Z-WAVE
OPERATOR

1. Press and hold the Learn button on the I-Drive
TorqueMaster
button.

2. With the Wireless Gateway in close proximity to the
I-Drive TorqueMaster® Pro, press and hold the copy button on
the Wireless Gateway until all 3 LEDs are flashing.

3. Observe the 4 LEDs on the I-Drive TorqueMaster® Pro. If
programming is successful, the LEDs will begin blinking at a
different rate, and then turn off. If not, then you may have to
move the Wireless Gateway closer or change the orientation.

4. The Z-Wave Light Kit will now come on when the
operator is engaged. The light will automatically shut off after
approximately 5 minutes. Additionally, by default, Scene 3 will
turn off Scene 1. Therefore, the light can be turned off by
pressing Scene 3 on the Wireless Gateway.

®

Pro until all 4 LEDs are blinking. Release the

(3) Mating Slots

Light Bulb

(Not Included)

Caution!

Use Only 19W Max.

COMPACT
FLUORESCENT

Caution!

Use Only 15W Max.

TYPE- A

Risk of Fire

Risk of Fire

Program Button

Power Socket

Light Fixture

Light Socket

Snap Tabs

Diffuser

LED

Light Button

Scene 1

Scene 2

Scene 3

Copy

Delete

Wireless Gateway

Pg 2