Wayne BRSPT130 Operating Instructions And Parts Manual

5. Protect electrical cord from sharp
objects, hot surfaces, oils, and chemicals.
Avoid kinking the cord and replace
damaged cords immediately.

IMPORTANT: Make sure there is adequate
room for the switch to operate.

6. A sump pit cover must be installed to
prevent debris from clogging or
damaging the pump or interfering with
pump.

Operation

Always disconnect the
power source before
attempting to install,
service, relocate or maintain the pump.
Never touch sump pump, pump motor,
water or discharge piping when pump
is connected to electrical power. Never
handle a pump or pump motor with
wet hands or when standing on wet or
damp surface or in water. Fatal
electrical shock could occur.

1. A ground fault circuit interrupter (GFCI)
is required.

Risk of electrical

shock! This pump is
supplied with a grounding conductor
and grounding type attachment plug.
Use a grounded receptacle to reduce
the risk of fatal electrical shock.

Never cut off the round grounding
prong. Cutting the cord or plug will
void the warranty and make the pump
inoperable.

Installation

1. Install pump in a sump pit with minimum
size as shown in Figure 1. Construct sump
pit of tile, concrete, steel or plastic.

2. The unit should be located and rest on
a solid, level foundation. Do not place
pump directly on clay, earth, gravel or
sandy surface. These surfaces contain
small stones, gravel, sand, etc. that may
clog or damage the pump and cause
pump failure.

Flood risk. If

flexible discharge
hose is used, make sure pump is
secured in sump pit to prevent
movement. Failure to secure pump
could allow pump movement and
switch interference and prevent pump
from starting or stopping.

3. Thread check valve (Blue Angel™ offers

Model 66005-BLA1) into pump body
carefully to avoid stripping or cross
threading. Do not use pipe joint sealant.

4. Connect 1-1/2" rigid pipe to rubber boot

on check valve. Reverse boot for 1-1/4"
diameter pipe. Tighten hose clamps.

Support pump and

piping when
assembling and after installation.
Failure to do so could cause piping to
break, pump to fail, etc. which could
result in property damage and/or
personal injury.

Please read and save these instructions. Read carefully before attempting to assemble,
install, operate or maintain the product described. Protect yourself and others by
observing all safety information. Failure to comply with instructions could result in
personal injury and/or property damage! Retain instructions for future reference.

Description

The submersible pump is designed for
indoor home sump applications. The unit is
equipped with an 8-ft long, 3-prong
grounding type power cord. Motor is oil
filled and sealed for cooler running and
designed to operate under water. A float
switch is provided for automatic pump
operation. This pump is not suitable for
aquatic life.

General Safety
Information

Do not use to pump
flammable or explosive
fluids such as gasoline, fuel oil,
kerosene, etc. Do not use in a
flammable and/or explosive
atmosphere. Pump should only be used
to pump clear water. Personal injury
and/or property damage could result.

This pump is not

designed to handle
salt water, brine, laundry discharge or
any other application which may
contain caustic chemicals and/or
foreign materials. Pump damage could
occur if used in these applications and
will void warranty.

All wiring must be

performed by a
qualified electrician. Failure to follow
this warning could result in fatal
electrical shock.

If the basement has water
or moisture on the floor,
do not walk on wet area
until all power is turned off. If the
shutoff box is in the basement, call an
electrician. Remove pump and either
repair or replace. Failure to follow this
warning could result in fatal electrical
shock.

A backup system

should be used.
Blue Angel™ offers Model BSP15 and
BSP25

Operating Instructions and Parts Manual BRSPT130

350800-002 1/07

Tether 14"

Min. Diameter

Submersible Sump
Pump

14"

Figure 2

Grounded
Outlet

24"

Figure 1

For parts, product & service information

visit www.blueangelpumps.com

© 2007 Blue Angel™ Pumps

5. While the pump is draining the pit,
verify that the discharge piping is
carrying the water to a point several feet
away from the foundation.

If pump discharge

line is exposed to
freezing temperature, the exposed line
must be pitched to drain. Trapped
water will freeze and damage the
pump.

Maintenance

Always disconnect the
electrical supply before
attempting to install,
service, relocate or
perform any maintenance. If the power
source is out of sight, lock and tag in
the open (off) position to prevent
unexpected power application. Failure
to do so could result in fatal electrical
shock. Only qualified electricians

2. This pump is only for use on 120 Volt
(single-phase), 60 hz, 15 amp service and
is equipped with a 3-conductor cord and
3-prong, grounding type plug. Insert the
float switch cord plug directly into a
120 volt outlet.

3. Insert the pump power cord plug
directly into the back of the float switch
cord plug (See Fig. 2).

4. Fill sump with water. The pump will
start automatically when the water has
filled the sump to the cut-in level. The
pump will stop when the water reaches
the cut-out level. See specifications for
cut-in/out levels. The pump will cycle
thereafter as required.

Do not operate the

pump unless it is
submerged in water. Dry running
causes pump failure.

The motor is

equipped with an
automatic reset thermal protector.

2

Operating Instructions And Parts Manual

Troubleshooting Chart

Symptom Possible Cause(s) Corrective Action

Pump will not start
or run

Pump starts and
stops too often

Pump will not shut
off or thermal
protector turns off

Pump operates but
delivers little or no
water

1.Blown fuse

2.Low line voltage

3.Defective motor

4.Defective float switch

5.Impeller bound-up

6.Float obstructed

1.Backflow of water from
piping

2.Faulty float switch

1.Defective float switch

2. Obstacle in piping

3.Float obstructed

1.Low line voltage

2.Plugged impeller

3.Obstructed piping

4. Excessive lift height
(water has to go higher
than pump can handle)

1.If blown, replace with proper sized fuse or reset breaker

2.If voltage is under 108 volts, check wiring size

3.Replace pump

4.Replace float switch

5.If impeller will not turn, remove housing and remove
blockage

6.Make sure float moves freely up and down

1.Install or replace check valve (Blue Angel™ check valve kit
#66005-WYN)

2.Replace float switch

1.Replace float switch

2.Remove pump and clean pump and piping

3.Make sure float move freely up and down

1.If voltage is under 108 volts, check wiring size

2.Clean out impeller

3.Remove pump and remove obstruction from piping or
reposition piping to prevent obstruction

4.Reposition pump to a suitable position to decrease lift
height

should repair this unit. Improper repair
could result in fatal electrical shock.

1. Let the pump cool for a minimum of
two hours before servicing because the
pump contains hot oil under pressure
and the motor is hot.

2. Disassembly of the motor prior to
expiration of warranty will void the
warranty. If repairs are required, see
troubleshooting chart.

3. Inlet should be kept clean and free of all
foreign objects and inspected annually.
A clogged inlet will damage the pump.

4. Pump should be checked monthly for
proper operation.

This pump contains

dielectric oil for
cooling. This oil can be harmful to the
environment. Check the state
environmental laws before disposing
this oil.

www.blueangelpumps.com

3

BRSPT130

1 Tether Float Switch Kit 60022-001
2 Power Cord Kit 62003-001
3 Impeller 28541-001
4 Impeller Retaining Clip 67106-001

Ref. Parts Numbers
No. Description RSP-130

For Replacement Parts, call 1-888-636-6628

Please provide following information:

- Model number

- Serial number (if any)

- Part descriptions and number as shown
in parts list

Address parts correspondence to:

Blue Angel™
101 Production Drive
Harrison, OH 45030 U.S.A.

Replacement Parts List

• Only use factory parts to repair this pump.

1

2

www.blueangelpumps.com

Specifications

Power supply requirements.............120V, 60 hz

Motor................................................Single phase, oil filled

Liquid temperature range...............40°F to 120°F

Circuit requirements ........................15 amps (min)

Dimensions .......................................11" high x 9" base

Cut-in level (factory set) ..................Tether ...14"

Cut-out level (factory set)................Tether...7"

Construction

Motor housing .................................Glass reinforced thermoplastic

Volute ...............................................Thermoplastic

Base ...................................................Thermoplastic

Impeller.............................................Glass reinforced thermoplastic

Shaft..................................................Stainless steel

Seals ..................................................Buna N

Discharge ..........................................11/2" NPT

4

Limited Warranty

For one year from the date of purchase, Blue Angel™ will repair or re place, at its option, for the original
purchaser any part or parts of its Sump Pumps or Water Pumps (“Product”) found upon examination by Blue
Angel™ to be defective in materials or work man ship. Please call Blue Angel™ (888-636-6628) for instructions or
see your dealer. Be pre pared to provide the model number and the serial number when exercising this warranty.
All transportation charges on Products or parts submitted for repair or replacement must be paid by purchaser.

This Limited Warranty does not cover Products which have been damaged as a result of accident, abuse,
misuse, neglect, improper installation, improper maintenance, or failure to operate in accordance with Blue
Angel™’s written instructions.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, IN CLUD ING THOSE OF MER CHANT ­ABIL I TY AND FITNESS FOR A PARTICULAR PUR POSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF
PURCHASE. THIS IS THE EXCLUSIVE REM E DY AND ANY LIABILITY FOR ANY AND ALL INDIRECT OR
CONSEQUENTIAL DAM AG ES OR EXPENSES WHATSOEVER IS EXCLUDED.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusions or
limitations of incidental or consequential damages, so the above lim i ta tions might not apply to you. This
limited war ran ty gives you specific legal rights, and you may also have other legal rights which vary from
state to state.

In no event, whether as a result of breach of contract warranty, tort (in clud ing negligence) or otherwise, shall
Blue Angel™ or its suppliers be liable for any special, consequential, incidental or penal damages including, but
not limited to loss of profit or revenues, loss of use of the products or any associated equipment, damage to
associated equip ment, cost of capital, cost of substitute products, facilities, services or replacement power,
downtime costs, or claims of buyer’s cus tom ers for such damages.

You MUST retain your purchase receipt along with this form. In the event you need to exercise a warranty
claim, you MUST send a copy of the purchase receipt along with the material or correspondence. Please call
Blue Angel™ (888-636-6628) for return authorization and instructions.

DO NOT MAIL THIS FORM TO WAYNE. Use this form only to maintain your records.

MODEL NO._______________ SERIAL NO.__________________________ INSTALLATION DATE_____________

ATTACH YOUR RECEIPT HERE

Operating Instructions And Parts Manual

www.blueangelpumps.com