Submersible Utility
Pump
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
© 2000 Wayne Water Systems
Operating Instructions and Parts Manual TSC
Do not pump flammable or
explosive fluids such as gasoline, fuel oil, kerosene, etc. Do not use
in a flammable and/or explosive environment. Pump only clear water.
Personal injury and/or property damage will result.
Risk of electric shock! This
pump has not been tested for
use in swimming pool areas. Never
place pump in pools while people are
in the water.
Do not handle pump with wet
hands or when standing in
water or on a damp surface.
Risk of electric shock! This
pump is supplied with a
grounding conductor and grounding
type attachment plug. Use a grounded
receptacle to reduce the risk of fatal
electrical shock.
This pump con-
tains dielectric
motor oil for motor heat transfer.
Care should be taken when disposing
of this oil. Do not use this pump in
ponds or fountains because the motor
oil can be harmful to aquatic life.
2. Wear safety glasses at all
times when working with
pumps.
3. It is strongly recommended
that this unit be plugged into a
Ground Fault Circuit Interrupter
(GFCI). Consult a local electrician
for installation and availability.
4. Do not use the power cord or dis-
charge hose to carry or handle the
pump. Damage to the power cord
or discharge hose may occur. Use
the lifting ring supplied on the
pump.
351301-001 1/00
Installation and Operation
Always disconnect
electric supply
before attempting to install, service,
relocate or perform any maintenance.
If the power source is out of sight, lock
and TAG IN OPEN (OFF) POSITION to prevent unexpected power application.
Failure to do so could result in fatal
electrical shock!
This unit is not designed for
use in septic tanks or underground vaults to pump raw sewage or
effluents. Never use in hazardous or
explosive locations.
1. This pump has been designed to
attach to a standard garden hose.
Thread the female end of the garden hose to the male discharge on
the pump.
2. To reduce leakage between the
pump and the hose, place a hose
washer (not included) on the garden hose before installing to the
pump.
3. For best pump performance,
unwind the hose before starting the
pump. This will help remove any
kinks or binds in the hose and allow
the unit to pump with less
restriction.
4. Set the pump on a hard surface in
the water. Do not set the pump
directly on mud or sand surfaces.
This will cause the inlet screen to
clog.
5. The water level must be at least 1/2
inches for the pump to operate.
Water levels less than 1/2 inches will
not allow the impeller to contact
water and no water will be
pumped.
Description
This portable, submersible utility pump
is designed for non-automatic use in
water. The units are equipped with an
8 ft. 3-prong grounding type power
cord. The motor is oil filled and sealed
for cooler operation. The discharge fitting is designed for convenient attachment to a garden hose.
IMPORTANT: THIS PUMP IS NOT
SUITABLE FOR AQUATIC LIFE!
Unpacking
After unpacking the unit, carefully
inspect for any damage that may have
occurred during transit. Check for
loose, missing or damaged parts.
Danger indicates
an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Warning indicates
a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Caution indicates a
potentially hazardous situation which, if not avoided,
MAY result in minor or moderate
injury.
Notice indicates
important information, that if not followed, MAY cause
damage to equipment.
This manual contains information that
is very important to know and understand. This information is provided for
SAFETY and to PREVENT EQUIPMENT
PROBLEMS. To help recognize this
information, observe the following:
1. Read these rules and
instructions carefully.
Failure to follow these
instructions could cause
serious bodily injury and/or property damage.
Very Important Safety
Information
2
Operating Instructions and Parts Manual
Installation and Operation
(Continued)
Do not handle pump with wet
hands or when standing in
water or on a damp surface when the
unit is operating or fails to operate.
Always disconnect pump power cord
from power source before handling.
6. Plug the power cord into a grounded 115-volt AC power outlet. The
pump will start operating as soon as
the power cord is plugged into the
power outlet.
7. The pump will remove water down
to 1/8 inches of the hard surface the
pump was placed on.
8. The pump should be turned off
once the water level reaches the
1/8-inch mark.
Do not allow
pump to run dry.
The shaft seal depends on water for
lubrication. Operating pump without
water will damage the shaft seal and
cause pump failure.
Maintenance
Always disconnect electric
supply before attempting to
install, service, relocate or perform any maintenance. Failure to do so
could result in fatal electrical shock.
Minimal service is required for this
pump. If pump should fail to operate,
perform the following troubleshooting
guidelines:
1. The motor housing of the
pump is completely sealed
and requires no service.
Disassembly of the motor
housing or alteration of the power
cord could result in fatal electrical
shock.
2. Verify pump is operating correctly.
a. Disconnect pump from power
source.
b. Disconnect discharge hose from
pump.
c. Immerse pump in a bucket or tub
of water.
d. Plug power cord into a grounded
115 volt AC power outlet. If
pump operates correctly proceed
to step #3. If pump does NOT
operate, unplug power cord and
proceed to maintenance guideline item 4 in this section.
3. Verify discharge hose is correctly
installed.
a. Connect hose to another water
source such as a faucet. If water
flows through hose, proceed to
step 3b. If water is restricted, verify discharge hose is unwound.
Remove all kinks, bends or
obstructions in hose.
b. Verify pumping height does NOT
exceed 25 feet (See Figure 1). If
pumping height is greater than
25 feet, this pump will NOT work.
4. Periodic cleaning of pump is
required to maintain performance
of the pump. Follow the cleaning
steps listed below:
a. Unplug the power cord.
b. Remove the 3 screws at the bot-
tom of the pump.
c. Remove the volute cover. Note
the alignment marks.
d. Remove the gasket. Note how
the openings in the gasket align
with the openings in the pump
base.
e. Remove the debris and make sure
the impeller turns freely.
Figure 1 Water Level
25 Ft. Max.
Water Level
f. Replace the gasket making sure
the openings are aligned.
g. Replace the volute cover.
h. Replace the 3 screws.
3
Operating Instructions and Parts Manual
For Replacement Parts, call 1-800-237-0987
Please provide following information:
- Model number
- Serial number (if any)
- Part description and number as shown in parts list
Address parts correspondence to:
Wayne Water Systems
100 Production Drive
Harrison, OH 45030 U.S.A.
1 Power cord 31006-002 31006-002 1
2 Discharge fitting 15875 15875-002 1
3 Outer housing with o-ring 28053-001 28053-001 1
19023-001 19023-001 1
4 Impeller 23097 23097 1
5 Volute gasket 23122 23122 1
6 Volute cover with screen 28056-001 28056-002 1
Ref.
No. Description TSC130/250 TSC160 Qty.
1
2
3
4
5
6
4
Operating Instructions and Parts Manual
Limited Warranty
For one year from the date of purchase, Wayne Water Systems Division ("Wayne") will repair or re place, at its option, for
the original purchaser any part or parts of its Sump Pumps or Water Pumps (“Product”) found upon examination by
Wayne to be defective in materials or work man ship. Please call Wayne (800-237-0987) for instructions or see your dealer.
Be pre pared to provide the model number and the serial number when exercising this warranty. All transportation
charges on Products or parts submitted for repair or replacement must be paid by purchaser.
This Limited Warranty does not cover Products which have been damaged as a result of accident, abuse, misuse, neglect,
improper installation, improper maintenance, or failure to operate in accordance with Wayne’s written instructions.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, IN CLUD ING THOSE OF MER CHANT ABIL I TY
AND FITNESS FOR A PARTICULAR PUR POSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF PURCHASE. THIS IS
THE EXCLUSIVE REM E DY AND ANY LIABILITY FOR ANY AND ALL INDIRECT OR CONSEQUENTIAL DAM AG ES OR
EXPENSES WHATSOEVER IS EXCLUDED.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusions or limitations
of incidental or consequential damages, so the above lim i ta tions might not apply to you. This limited war ran ty gives you
specific legal rights, and you may also have other legal rights which vary from state to state.
In no event, whether as a result of breach of contract warranty, tort (in clud ing negligence) or otherwise, shall Wayne or
its suppliers be liable for any special, consequential, incidental or penal damages including, but not limited to loss of prof-
it or revenues, loss of use of the products or any associated equipment, damage to associated equip ment, cost of capital,
cost of substitute products, facilities, services or replacement power, downtime costs, or claims of buyer’s cus tom ers for
such damages.
You MUST retain your purchase receipt along with this form. In the event you need to exercise a warranty claim, you
MUST send a copy of the purchase receipt along with the material or correspondence. Please call Wayne (800-237-0987)
for return authorization and instructions.
DO NOT MAIL THIS FORM TO WAYNE. Use this form only to maintain your records.
MODEL NO._______________ SERIAL NO.__________________________ INSTALLATION DATE_____________
ATTACH YOUR RECEIPT HERE
Loading...