Wavion WBS5800 2S User Manual
WBS-2400 & WBS-5800
Outdoor Wi-Fi Sector Base Station
Installation Guide
Rev. 3
February 2009
Note: To better reflect the value of Wavion products we are changing the name of our product
family from Access Points (AP) to Wireless Base Stations (WBS), consequently the existing WS-
410 product name will be changed to Wavion WBS-2400.
The new product name emphasizes the difference in architecture (Multiple Radio system) and
the value to customer, superiority in performance (coverage, capacity, indoor penetration and
immunity to interference) of Wavion WiFi base station over any other standard outdoor WiFi
access point products available in the market.
All references in Wavion's documentation to WS-410 refer also to the WBS-2400, and vice
versa. Both products are exactly the same except for the name change.
Copyright Notice
©2006, 2007, 2008 Wavion, Inc. All rights reserved. Wavion is a registered trademark of
Wavion in the United States and certain other jurisdictions. Specifications are subject to change
without notice.
FCC Notice to Users and Operators
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user will be required to correct the interference
at his own expense. If this equipment does cause interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
correct the interference by using one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician.
Warning
by the party responsible for compliance could void the user’s authority
to operate the equipment.
:
Changes or modifications to this unit not expressly approved
Note
:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note
:
According to the FCC rules the WBS-5800 unit must only be
used for fixed point to point applications with fixed clients.
R&TTE Compliance Statement
This equipment (ETSI-models only) complies with all the requirements of DIRECTIVE
1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on
radio equipment and telecommunication terminal Equipment and the mutual recognition
of their conformity (R&TTE)
Installation Guide 3
Contents
Chapte r 1
Chapte r 2
Chapte r 3
Chapte r 4
Chapte r 5
Chapte r 6
Chapte r 7
Chapte r 8
Chapte r 9
Chapte r 1 0
Chapte r 1 1
Chapte r 1 2
About This Guide ........................................................................ 5
Preface ....................................................................................................5
Conventions .............................................................................................5
Contacting Technical Support ....................................................................6
Introduction ............................................................................... 7
Package Content ........................................................................ 8
Installing the Wavion WBS-2400/5800 Sector Base Station .. 10
Important Safety Instructions.................................................................. 11
Preparing for Installation......................................................................... 12
Choosing a Location................................................................................ 13
Preparing the Site ................................................................................... 13
Mounting Strategies................................................................................ 14
Using Hose Clamps ................................................................................. 14
Mounting on a Pole/Streetlight ................................................................ 15
Grounding the Data Protection Device...................................................... 18
Connecting Power and DATA................................................................... 20
Safety Information for the Wavion WBS-2400/5800 .................................. 24
Service Instructions ................................................................................ 25
Product Specification WBS-2400 Sector.................................. 26
Antenna 2.4GHz Specifications and Patterns .......................... 30
MT-343037/CV 2.4GHz Sector Antenna .................................................... 30
Product Specification WBS-5800 ............................................. 33
Antenna 5.8GHz Specifications and Patterns .......................... 39
MT-463009CV 5.8GHz Antenna Azimuth Patterns directional Antenna ........ 39
Installation Accessories ........................................................... 41
Ethernet Cables ...................................................................................... 42
Sun Protection ........................................................................................ 42
Lightning Protection ................................................................................ 42
Power Over Ethernet............................................................................... 42
Wind Loading Considerations .................................................. 43
Acronyms.................................................................................. 44
Appendix A: WBS-2400/5800 Product list............................... 46
4 Wavion Networks
Chapter 1
About This Guide
Preface
This guide details the Wavion WBS-2400/5800 Sector installation procedures. The
intended audience of this document is trained technical professionals.
Conventions
The exclamation point within a triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in
the literature accompanying the product.
The lightning flash with an arrowhead symbol within a triangle is intended to
alert the user to the presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The notebook is intended to alert the user of a note containing further
information.
5 Wavion Networks
About This Guide
Contacting Technical Support
For technical support, contact Wavion using these methods:
Wavion Technical Support
Wavion
Address:
Telephone: +972-4-9097300
Fax: +972-4-9097322
6 Hayetzira Street,
PO BOX 580
Yoqneam Illit, 20692
Israel
Email:
Web:
support@wavionnetworks.com
www.wavionnetworks.com
6 Wavion Networks
Introduction
Chapter 2
Introduction
WBS-2400/5800 Sector a high capacity, IP services oriented Broadband Wireless access system.
WBS-2400/5800 Sector is a new category of Broadband Wireless Base Station designed from
the ground up for metro-Wi-Fi deployments. The system employs wireless packet switched data
technology to support high-speed IP services including fast Internet and Virtual Private
Networks. WBS-2400/5800 Sector users are provided with a network connection that is always
on, supporting immediate access to the Internet and other IP services at high data rates. The
system is designed for cellular-like deployment, enabling the system architecture to vary in size
and structure. A system can include any number of cells, each containing several base station
access units for better coverage of densely populated areas.
It is based on three antennas and radios and custom-built ASICs, utilizes Wavion's powerful
multi-antenna signal processing technologies, and provides significant performance gains to offthe-shelf 802.11 standards-based
The WBS-2400/5800 Sector may be mounted on streetlights or rooftops and may be
easily interfaced with wired internet connections, wireless mesh or backhaul equipment.
Complete management of the WBS-2400/5800 Sector is provided through SNMP, a
graphical user interface, and SYSLOG services.
Installation Guide 7
Package Content
Check that the package contains:
• POE injector unit with wall mounting kit
• Outdoor Unit
• Pole mounting bracket for the outdoor unit
• Allen head wrench with 4 screws
• Waterproof sealing tape for IP67 (band to sealing rubber)
Additional Equipment and Tools required for Installation
• Ethernet cable (straight for connecting to a hub/switch)
• Crimping tool for RJ-45 connectors.
• Ground cable with an appropriate termination.
• Mains plug adapter or termination plug (if the power plug on the supplied AC
power cord does not fit local power outlets).
• Portable PC with Ethernet card and Telnet software and a straight Ethernet
cable.
WARNING: Use straight Ethernet (POE) cable connecting the injector to AF unit in order to have
all the features work properly (reset button and Link LED). Using cross cable might cause turn
Link led to “ON” permanently and also may be the cause software reset. DATA cable connecting
the injector to the network can be cross cable as well.
Chapter 3
8 Wavion Networks
Package Content
• Addition tools and materials, including appropriate means (e.g. a pole) for
• 1/4-inch flat blade screwdriver
installing the outdoor equipment.
WARNING: ONLY experienced installation professionals who are familiar with local
building and safety codes and, wherever applicable, are licensed by the
appropriate government regulatory authorities should install outdoor units and
antennas. Failure to do so may void the WBS-2400/5800 product warranty and
may expose the end user or Service Provider to legal and financial liabilities.
Wavion and its resellers or distributors are not liable for injury, damage or
regulation violations associated with the installation of Outdoor Units or antennas
Installation Guide 9
Chapter 4
Installing the Wavion WBS-2400/5800 Sector
Base Station
This guide explains how to safely install the Wavion WBS-2400/5800 Sector Base Station.
The following topics are covered in this chapter:
• Important Safety Instructions
• Preparing for Installation
• Mounting Strategies
• Using Hose Clamps
• Mounting on a Pole, or Streetlight
• Grounding the Wavion WBS-2400/5800
• Connecting Power and Data
• Safety Information for the Wavion WBS-2400/5800
• Service Instructions
10 Wavion Networks
Important Safety Instructions
W
ARNING: It is illegal to modify the construction of this product. Modifying
the operating frequency or enhancing the transmit output power through the
use of external amplifiers or other equipment is specifically disallowed by the
"Telecommunications Act."
W
ARNING: This device is for outdoor or indoor use with conditions that no
harmful interference to authorized radio stations results from the operation
of this device. This device shall not influence aircraft security and/or
interfere with legal communications as defined in the "Telecommunications
Act." If this device is found to cause interference, the operator of this
equipment shall cease operating this device immediately until no
interference is achieved.
Note
: This device must be installed by a trained professional, value added
reseller or systems integrator who is familiar with RF planning issues and the
regulatory limits in the United States of America.
Caution
Do not defeat the safety purpose of the grounding.
Caution
Caution
required when the apparatus has been damaged in any way. For example, if
the power-supply cord or plug is damaged, liquid has been spilled on the
apparatus, objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, it does not operate normally, or has been
dropped.
Warning:
is a risk of personal injury or death if the WBS-2400/5800 antennas come
near electric power lines. Carefully read and follow all instructions in this
manual. By nature of the installation, you may be exposed to hazardous
environments and high voltage. Use caution when installing the outdoor
system.
Warning:
: Read and save these instructions. Heed all warnings. Follow all instructions.
: Only use attachments/accessories specified by the manufacturer.
: Refer all servicing to qualified service personnel. Servicing is
Risk of personal injury or death when installing this device! There
This apparatus must be connected to earth ground
Warning:
Do not open the unit. There is a risk of electric shock inside.
Caution:
approved
in this manual could void your authority to operate this equipment.
You are cautioned that any change or modification not expressly
Installation Guide 11
Caution
performed by qualified personnel.
Caution
devices having an environmental rating equal to or better than the enclosure rating to
close all unfilled openings.
Caution
suppressor device in the branch circuit to limit expected transients to Overvoltage
Category II values. The limits are based on IEC60664 and are also located in Table 2H
of UL60950 (for mains 110V, the transient rating is 1500V).
Caution
antennas.
Caution
kept when the system is operated.
Caution
instructions
: There are no user-serviceable parts inside. All service must be
Only UL listed parts and components will be used for installation. Use UL listed
To maintain Overvoltage (Installation) Category II, install a suitable surge
The WBS-2400/5800must be installed only with the equipped
A minimum distance of 40cm from the WBS-2400/5800X's antenna should be
Read and save these instructions. Heed all warnings. Follow all
Preparing for Installation
ONLY experienced installation professionals who are familiar with local building and
safety codes and, wherever applicable, are licensed by the appropriate government
regulatory authorities should install outdoor units and antennas.
The following lists the equipment required for installation and explains how to prepare
the installation site.
WARNING
the operating frequency or enhancing the transmit output power
through the use of external amplifiers or other equipment is illegal.
WARNING
that operation of this device causes no harmful interference to
authorized radio stations. This device shall not influence aircraft security
and/or interfere with legal communications. If this device is found to
cause interference, the operator of this equipment shall cease operating
this device immediately.
: Do not modify the construction of this product. Modifying
This device is for use outdoors or indoors on the condition
12 Wavion Networks
Choosing a Location
To ensure the optimal performance select the locations for the equipment using the following
guidelines:
The antenna (integrated on the front panel of the outdoor unit) should provide a
direct, or near line of sight, with the sector location that need to be covered.
The antenna should be aligned to face the CPEs that aim to be in service, higher
the placement of the antenna, the better the achievable link quality (but not in all
cases).
Average rooftop (depend on the topology of the location) should be
The location of the outdoor unit should enable easy access to the unit for
installation and testing
Avoid installations in locations that devices operating in the same frequency
range.
The outdoor unit should be installed at the highest point of a metal pole that
there will be no interference caused by RF reflections. If this is not possible, it
should be installed at least 3 meters from the metal pole.
It is recommended to use maximum distance possible from an RF radiating
source.
Preparing the Site
1. Follow the appropriate electrical and building codes to ensure safe and
durable wiring.
2. Follow the National Electrical Code (NEC) requirements, unless local codes in
your area take precedence over the NEC code
3. The length of the indoor-to-outdoor Ethernet cable should not exceed 90
meters. The length of the Ethernet cable connecting the indoor unit to the
user's equipment, together with the length of the Indoor-to-Outdoor cable,
should not exceed 100 meters.
4. An appropriate ground cable should be available. Connect a grounding cable
between the Ground terminal of the outdoor unit and a good ground
connection.
Please refer to standards for building entrance protection.
Installation Guide 13
Mounting Strategies
Consider the available mounting structures and antenna clearance when choosing a
mounting location. Wavion outdoor unit WBS-2400/5800 Sector should be mounted
horizontal pole only the antennas pointing vertically and clear of obstruction.
It is recommended to attach ground and data cables to the WBS-2400/5800 Sector prior
to mounting. Before mounting the WBS-2400/5800 Sector, read the wiring instructions in
Grounding the Wavion WBS-2400/5800
Note
: The WBS-2400/5800 should be mounted with at least 4 ft/3 Meter of
clearance around the antennas to eliminate potential interference from the
mounting structure.
and
Connecting Power and Data.
on
Figure 4.1 Pole mounting kit for the Outdoor Unit & Sealing kit
Using Hose Clamps
Special hose clamps that include threaded holes are used by the mounting assembly to
secure the WBS-2400/5800 Sector to the mounting structure. Figure 4.2 demonstrate
how to correctly use the hose clamps. The bands must be threaded through holes in the
pole bracket, and then attached horizontal pole and tightened.
There are two pairs of threaded holes on the back of the unit, enabling to use the special
clamps for mounting the unit on diverse pole diameters.
14 Wavion Networks
Loading...