WaveLinx Relay Switchpack Installation Manual
WaveLinxInstallation Instructions
Relay Switchpack with 0-10V
WARNING
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this product
must be performed by a qualified electrician. This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and operation of
the product and hazards involved.
Before installing or performing any service, the power MUST be turned OFF at the branch circuit breaker. According to
NEC 240-83(d), if the branch is used as the main switch for a fluorescent lighting circuit,
the circuit breaker should be marked with “SWD”. All installations should be in compliance with the National Electric
Code and all state and local codes.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting any
maintenance. Disconnect power at fuse or circuit breaker.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Due to sharp edges, handle with care.
Failure to comply with these instructions may result in serious injury (including death) and property damage.
DISCLAIMER OF LIABILITY: Eaton assumes no liability for damages or losses of any kind that may arise from the improper, careless,
or negligent installation, handling or use of this product.
IMPORTANT: Read carefully before installing product. Retain for future reference.
NOTICE: Product/component may become damaged and/or unstable if not installed properly.
Note: Specifications and dimensions subject to change without notice.
ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on delivery receipt.
File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be filed within 15 days of delivery. All
damaged material, complete with original packing must be retained.
NOTICE: All new wiring must be fully veried before applying power.
NOTICE: Designed for indoor installation and use only. Dry location rated.
Relay Switchpack with 0-10VWaveLinx
General Information
Overview
The Wireless Relay Switchpack with 0-10V (WSP-MV-010) control is an integral part of the WaveLinx Connected Lighting (WCL)
system and offers 120-277VAC 20 amp zero crossing relay control and continuous 0-10V dimming control of LED and non LED loads.
The wireless relay Switchpack with 0-10V control also supports 20 amp plug load control. The WSP-MV-010 is powered by the 120277VAC circuit it is controlling and provides simple junction box mounting through 1/2” knockout. The wireless relay Switchpack with
0-10V control operates on a wireless mesh network based on IEEE 802.15.4 standards.
The intended use of the WaveLinx Relay Switchpack with 0-10V output is for commercial lighting and control integration. Listed below
are a few operating notes related to the switch pack.
• The basic WaveLinx system uses some number of WaveLinx Relay Switchpacks with 0-10V output. Each is powered by AC line
voltage 120-277VAC (+/- 10%) input power supply with Line, and neutral terminals.
• The WaveLinx Relay Switchpack also includes a 0-10 V output to allow the entire system to be controlled by a single 0-10 V
control device.
• The WaveLinx Relay Switchpack will support up to 120mA current sink at the 0-10V output and it can switch up to
20 amps plug loads.
Plenum Rating
Most of the components in this system are intended to be mounted above the ceiling tiles, in an area that could be intended for air
handling. For this reason, all of the WaveLinx Relay Switchpack cabling is plenum rated.
ote: N The components do not meet the plenum rating standards for Chicago without additional measures.
IB503100EN page 2
October 2020
www.cooperlighting.com
Relay Switchpack with 0-10V Wavelinx
Junction Box Mounting
The WaveLinx Relay Switchpack with 0-10V output is
designed to be mounted to a solid surface (horizontal or
vertical) and attached to a Junction Box.
Installation instructions are included for connecting the
leads to the fixtures.
10V Wiring Detail
20 amp circuit from
circuit breaker
To 0-10 V Continuous
Dimming 20 amp luminaires
Black (Incoming Hot)
Wireless Relay Switchpack
White (Neutral)
Red (Load Out)
Purple (0-10V +)
Gray (0-10V -)
Junction Box
White (Neutral)
Switchleg
with 0-10V Control
(WSP-MV-010)
Plug Load Wiring Detail
20 amp circuit from
circuit breaker
To 20 amp split
receptacle
Black (Incoming Hot)
Wireless Relay Switchpack
with 0-10V Control
(WSP-MV-010)
White (Neutral)
Red (Load Out)
Purple (0-10V +)
Gray (0-10V -)
Junction Box
White (Neutral)
Switchleg
Controlled Switchleg Neutral
20 amp split
receptacle
Continuous Powered 20amp circuit
www.cooperlighting.com
IB503100EN page 3
October 2020
Loading...