Watts Premier WP-2 LCV, WP-2 BVC Installation, Operation And Maintenance Manual

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

MODELS:

WP-2 LCV, WP-2 BVC

WP-2 BVC has been tested by Bio Vir as a Microbiological Water Purier based upon the

recommendations set forth in the USEPA Guide Standard and Protocol for Microbiological Water

Puriers (OPP Task Force Report, 1987)

Please read carefully before proceeding with installation. Your failure to follow any attached instructions or

operating parameters may lead to the product’s failure.

Refer to enclosed warranty for operating parameters to ensure proper use with your water supply.

Watts Premier, Inc. 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381
Phone: [phone] www.premierH2o.com Fax: [phone]

Manual #: 199389 Manual Date: 02/05/2009

Thank you for your purchase of a state of the art Watts Premier Water Treatment system.

WP-2 BVC Microbiological Water Treatment System:

Watts Premier WP-2 BVC water treatment system contains a patented State of the Art
Microbiological Filter. This lter has been independently tested and certied to remove disease

causing microorganisms from the drinking water, including bacteria, viruses and protozoan cysts.
While these water contaminants may not be in your water at all times, it provides a level of security
in the event there is a short term water concern such as a boil alert.

This lter has also been tested and certied to reduce chlorine tastes and odors from the drinking
water providing you great tasting water in addition to the comfort in knowing you have the protection
of the Microbiological Filter. See performance data sheet for individual contaminants and reduction
performance.

WP-2 LCV Water Treatment System:

Watts Premier WP-2 LCV water treatment system contains a heavy duty lead, cyst and VOC
lter block. This specialty formulated block is capable of reducing lead, cryptosporidium, Giardia,
Entamoeba as well as harmful Chemicals (See performance data sheet for complete list of
VOC’s). It is estimated that VOC’s are present in one-fth of the nation’s water supplies. These
water contaminants can enter ground water from a variety of sources including localized use of
herbicides and pesticides, gasoline or oil spills, leaking underground fuel tanks, septic system
cleaners, and chemicals used in the dry-cleaning industry. See performance data sheet for individual
contaminants and reduction performance.

System Maintenance

Just because you can not taste it, does not mean that it is not there. Many contaminants in the
drinking water are undetectable to the taste. Additionally, over time if you do not replace the
lter elements, other bad tastes and odors will be apparent in your drinking water. This is why
it is important to change your lters at the recommended intervals as indicated in this system
manual.

When replacing any of the lter elements, pay special attention to any cleaning instructions. Should
you have any further questions please refer to our web site at www.premierH2o.com or call our
customer service department at 1-800-752-5582.

2

Table of Contents

Maintenance Record......................................................................................................

Operational Parameters ................................................................................................

Contents of WP-2 System .............................................................................................

Tools Recommended For Installation ............................................................................

Installation......................................................................................................................

Drill / Punch a Hole for Watts Top Mount Faucet...........................................................

Watts Top Mount Faucet Installation .............................................................................

Adapt-a-Valve Installation................................................................................................

System Start Up...............................................................................................................

Filter Change..................................................................................................................

Parts Listing ..................................................................................................................

Performance Data Sheets..............................................................................................

California Certicate.......................................................................................................

Other Products by Watts................................................................................................

Warranty Registration.....................................................................................................

Removing Chlorine from your shower...........................................................................

Warranty .......................................................................................................................

3
4
4
4
4
5
6
7
7
8
9
10-12
13
14
15-16
17
18

Service Record

Date of Purchase:__________ Date of Install:___________ Installed by:_____________

Date

Sediment
Filter
(6 months)

Model Number:__________ Serial Number:___________

BVC/LCV
Filter
(6 Months)

Date

Sediment
Filter
(6 months)

BVC/LCV
Filter
(6 Months)

NOTES:

3

Operational Parameters

Installation needs to comply with state and local plumbing regulations.

Maximum Minimum
Operational Temperature 100°F (37.8°C) 40°F (4.4°C)
Operating Pressure 85 psi (5.98 kg/cm²) 20 psi (1.406 kg/cm²)
pH Parameters 10 5
Flow Rate 0.5 GPM @ 60 psig

Contents of Under Counter System

1 WP-2 Unit
2 Filters
1 Parts Bag
1 Faucet Assembly

If any of the items are missing, please contact Watts Premier prior to installing

Tools Recommended For Installation

A small knife
Variable speed drill
1/8” (3mm), 1/4” (6.4 mm) and 7/16” (11.0mm) drill bits
1/2” Diamond Tip Drill bit (for porcelain sinks)
1/2” hole punch (for stainless steel sinks)
1/2” and 5/8” open-end wrenches (or adjustable wrenches)
Phillips screwdriver

Installation

This system has been designed to t under most kitchen sinks. Please read the entire manual carefully
before proceeding with installation.

Step 1: Mounting System Under Sink

(A) Locate a space under the sink that

allows the unit to be mounted close
to the cold water supply and allows
for easy access during maintenance
and filter changes. System must
be installed to the cold water supply
only. Allow approximately 2” (5cm)
clearance between the bottom of the
lter housing and the oor of the sink
cabinet.

(B) Using the mounting holes on the

bracket, mark the location for the
mounting screws on the cabinet wall
under the sink.

(C) Screw the (2) screws into the wall at

the marked location.

(D) Hang the module on the screws using

the mounting holes in the bracket.

Two Stage Under Counter (WP-2)

Counter Top

Blue

Tubing

HOT

Sink

Green
Tubing

COLD

4

Drill a Hole for the Faucet in a Porcelain Sink

Note:

Step 1

Step 2

Step 3

Most sinks are pre drilled with 1 ½” or 1 ¼” diameter hole that you can use for your
faucet. (If you are already using it for a sprayer or soap dispenser, see step 1)

Porcelain sinks are extremely hard and can crack or chip easily.
Use extreme caution when drilling. Watts Premier accepts no responsibility for
damage resulting from the installation of faucet.
Diamond tip drill bit is recommended for drilling in porcelain.

Determine desired location for the faucet on your sink and place a
piece of masking tape over where the hole is to be drilled. Mark the
center of the hole on the tape.

1

Using a variable speed drill set on the slowest speed, drill a
hole through both porcelain and metal casing of sink at the marked
center of the desired location. Use lubricating oil or liquid soap to keep
the drill bit cool (If drill bit gets hot it may cause the porcelain to crack
or chip).

Using a 1/2” Drill Bit, proceed to drill the larger hole. Keep drill speed
on the slowest speed and use lubricating oil or liquid soap to keep the
hole saw cool during cutting.

/8“ pilot

Step 4

Make sure the surroundings of the sink are cooled before mounting the
faucet to the sink after drilling and remove all sharp edges.

Punch a Hole for the Faucet in a Stainless Steel Sink

Note:

Step 5

If mounting faucet to a Stainless Steel Sink you will need a 1/2”
Hole Punch. The faucet opening should be centered between the
back splash and the edge of the sink, ideally on the same side as
the vertical drain pipe.

Drill a ¼” pilot hole. Use a 1/2” Hole Punch and an adjustable wrench
to punch the hole in the sink.

The faucet can now be installed.

5

WATTS Premier Monitored & Non-Monitored
(Top Mount) Faucet Installation

Minimum Maximum
Mounting Hole Size .5” 1.25”
Torque on Toggle Bolt 5lb.in. (max)

Step 6

Step 7

Step 8

Step 9

Remove faucet base & spout from their respective plastic
bags. Feed the faucet tubing through the round rubber gasket
which you will nd in the faucets parts bag. Peel the white
backing from the upper side of the gasket and press rmly
on to the base of the faucet. From above the sink, feed the
faucet tubing & toggle bolt down through the .5” mounting
hole in the sink.

Peel the white backing from the bottom side of the rubber
gasket, align the faucet base so that the handle is on the
right side and press the faucet base down rmly over the
mounting hole. Turn the handle down (towards you) to the
“ON” position to reveal the tightening screw (located where
the spout will be inserted). Using a Phillips head screwdriver,
turn the screw clockwise until the toggle bolt secures the
faucet base snug onto the sink top, do not over torque toggle
bolt (5lb.in. max)

Once the faucet base is securely fastened to the sink top,
insert the faucet spout into the faucet base until it is fully
seated. Turn the handle up (away from you) to the “OFF”
position.

Connect the 3/8” blue tube from faucet to the 1/4” blue
tube from the system using the 3/8” x 1/4” union provided.

Faucet Battery Installation

Line from Unit

Line from Faucet

Step 10

Remove the faucet battery from the plastic bag. Locate the faucet battery compartment drawer on the base of the faucet. Use
a small screwdriver to pry on the notch at the compartment drawer face and slide the drawer out. Insert the battery into the
battery compartment drawer.

NOTE: The + side of the battery faces up. The compartment drawer will not slide in if the battery is installed upside
down.

Once the battery is in place, slide the battery compartment drawer back into the base until it is ush.

When the battery is rst installed, both the red and green lights will ash to indicate that both lights are functional. Thereafter, it will
ash green only when the faucet handle is turned to the “ON” position. When your system is ready to be serviced (approximately
six months) you will see the light ash red when the handle is turned to the “ON” position.

NOTE: If your water usage is high the red light may activate sooner than six months indicating the need for lter
replacement.

This faucet provides an electronic monitor that will tell you when it is time to replace the lters in your water treatment
device. The light indicator will be green for the life of the lter, turning red once the life of the lter has been reached.
This can occur after six months of use, or sooner for heavy water usage. The battery life is expected to last one
year, however, under heavy use the battery may need to be replaced sooner. For replacement, look for battery
number CR2354 (Watts p/n:116082) which should be available at your local battery store or contact Watts Premier
at 800-752-5582. You may also order online at www.premierH2o.com.

6

Adapt-a-Valve Installation

Caution: Water supply line to the system must be from the cold water supply line.
Hot water will severely damage your system.

(A) Turn off the main supply water to the house.

Note: Housing plumbing may be the opposite of that shown in Figure B.

(B) Turn off the cold water supply to the faucet by turning the angle stop valve clockwise

until it is completely off. Drain any water in the line by opening the faucet cold side.

(C) Attach adapt-a-valve as illustrated in the center photo below, choosing the conguration

that ts your plumbing.
(D) Attach the loose end of the green tube to the Adapt-a-Valve, remove a brass nut,
plastic sleeve and brass insert from the parts bag. Place nut on the tube rst, then
the plastic sleeve (small taper end of plastic sleeve must point to the end of tube) and
then insert the brass Insert into the end of the tube (see Figure C). Insert the green
tube into the ¼” opening on the adapt-a-valve until it stops. Slide nut and sleeve down
and thread onto the male pipe threads. Use a ½” wrench to securely tighten.

(E) Turn on water supply and open the Adapt-a-valve. Check for leaks.

Figure B

Conguration for 3/8”

compression ttings

HOT

Correct installation of

Figure C

Figure C

the Adapta Valve

COLD

Conguration for 1/2” ttings

System Start Up

(A) Turn faucet handle to the open position to start the ow of water through the unit. Run 7

gallons of water through the unit in order to ush out the normal black carbon nes (it will
“sputter” until the air is purged out) from the unit. Initially, the water may appear cloudy which
is due to tiny air bubbles and it will clear up shortly. Close the faucet when nished.

(B) Check for leaks. If you have any leaks, shut off the water supply to your system, tighten

any ttings / housings and restart unit.

7

Filter Change

Watts Premier recommends changing the lter element every 6 months. However lter life
may vary depending on local water conditions and water use.

Use Watts Premier’s replacement cartridge only. Other lters may look the same, but only
lters by Watts are manufactured to t your WP-2 lter unit in order to ensure proper reduction
of water contaminants.

Sediment Pre-Filter
WP-2 BVC & WP-2 LCV Part# 104017

Carbon Block Filter
WP-2 BVC Part# 101003
WP-2 LCV Part# 101014

(A) Turn off incoming water supply to the WP-2 unit by
turning the needle valve on the adapt-a-valve clockwise.

Note: There will be water in the lter housing. Lift the
faucet handle to relieve the water pressure.

(B) Remove lter housing from lid by turning it to the left,
as shown in Figure D.

(C) Remove used lter cartridge and discard.

NOTE: Do not discard lter-housing o-ring.

Figure D

(D) Clean inside of lter housing with warm soapy water
and rinse well to remove soap.

(E) Lubricate o-ring with water-soluble lubricant (i.e. K-Y Jelly ®).

NOTE: Do not use Petroleum based lubricants such as Vaseline ®.

(F) Seat o-ring in groove in lter housing and insert new lter cartridges into appropriate lter

housing.

(G) Screw lter housing onto lid as shown in Figure D.

(H) Turn on water supply to lter unit by turning needle valve on Adapt-a-Valve counter clockwise

and check system for leaks periodically over the next 24-48 hours.

To Loosen To Tighten

Reset the Electronic Monitor Light

To reset the electronic monitor during replacement of lters, simply slide out the
battery from the base of the faucet and reinsert.

8
9

Performance Data Sheet

Watts Premier Inc.

8716 W Ludlow Drive Suite #1

Peoria, AZ 85381

WP-2 LCV

GENERAL USE CONDITIONS:

1: System to be used with municipal or well water sources treated and tested on regular basis to insure bacteriological safe
quality. DO NOT use with water that is micro biologically unsafe or of unknown quality without adequate disinfection
before or after the system. Systems certied for cyst reduction may be used on disinfected waters that may contain lterable
cysts.
2: Operating Temperature: Maximum 100o F (40.5o C) Minimum 40o F (4.4o C)
3: Operating Water Pressure: Maximum 85-psi (5.98 kg/cm2) Minimum 20-psi
4: Maximum ow Rate: 0.50 gpm (1.89 lpm)
5: Rated Capacity: 600 Gallons (2,200 liters)

RECOMMENDED REPLACEMENT PARTS AND CHANGE INTERVAL:

Note: Depending on incoming feed water conditions replacement time frame may vary.
Description Part Number Change time Frame Cost
Stage 1: Sediment: 5M-10 104017 6 Months or 600 gallons of water $ 3.50*
Stage 2: Carbon block 101014 6 Months or 600 gallons of water $28.95*

*All prices subject to change without notice

This system has been tested according to NSF/ANSI Standard 53 for the reduction of the substances listed below. The concentration of the indicated
substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as
specied in NSF/ANSI 53. Testing performed under standard laboratory conditions, actual performance may vary.

Substance

ALACHLOR* >98% 0.05 0.001

ATRAZINE* >97% 0.1 0.003

BENZENE* >99% 0.081 0.001

BROMODICHLOROMETHANE (TTHM)* >99.8% 0.300 +/- 0.30 0.015

BROMOFORM (TTHM)* >99.8% 0.300 +/- 0.30 0.015

CARBOFURAN (Furadan)* >99% 0.19 0.001

CARBON TETRACHLORIDE* 98% 0.078 0.0018

CHLOROBENZENE (Monochlorobenzene)* >99% 0.077 0.001

CHLOROFORM (TTHM)* >99.8% 0.300 +/- 0.30 0.015

CRYPTOSPORIDIUM (see Cyst) 99.99% minimum 50,000/mL 99.95%

CYST 99.99%

2, 4-D* 98% 0.110 0.0017

DBCP (see Dibromochloropropane)* >99% 0.052 0.00002

1,2-DCA (see 1,2-DICHLOROETHANE)* 95% 0.088 0.0048

1,1-DCE (see 1,1-DICHLOROETHYLENE)* >99% 0.083 0.001

DIBROMOCHLOROMETHANE
(TTHM;Chlorodibromomethane)*

DIBROMOCHLOROPROPANE (DBCP)* >99% 0.052 0.00002

o-DICHLOROBENZENE (1,2 Dichlorobenzene)* >99% 0.08 0.001

p-DICHLOROBENZENE (para-Dichlorobenzene)* >98% 0.04 0.001

1,2-DICHLOROETHANE (1,2-DCA)* 95% 0.088 0.0048

1,1-DICHLOROETHYLENE (1,1-DCE)* >99% 0.083 0.001

CIS-1,2-DICHLOROETHYLENE* >99% 0.17 0.0005

TRANS-1,2- DICHLOROETHYLENE* >99% 0.086 0.001

1,2-DICHLOROPROPANE (Propylene Dichloride)* >99% 0.08 0.001

CIS-1,3- DICHLOROPROPYLENE* >99% 0.079 0.001

DINOSEB* 99% 0.17 0.0002

EDB (see ETHYLENE DIBROMIDE)* >99% 0.044 0.00002

ENDRIN* 99% 0.053 0.00059

Percent

Reduction

>99.8% 0.300 +/- 0.30 0.015

Inuent Challenge

Concentration

(mg/L unless noted)

minimum 50,000/mL 99.95%

Maximum Permissible

Product Water
Concentration

10

Substance

ENTAMOEBA 99.99%

ETHYLBENZENE* >99% 0.088 0.001

ETHYLENE DIBROMIDE (EDB)* >99% 0.044 0.00002

FURADAN (see CARBOFURAN)* >99% 0.19 0.001

HALOACETONITRILES (HAN)*

BROMOCHLOROACETONITRILE 98% 0.022 0.0005

DIBROMOACETONITRILE 98% 0.024 0.0006

DICHLOROACETONITRILE 98% 0.0096 0.0002

TRICHLOROACETONITRILE 98% 0.015 0.0003

HALOKETONES (HK):*

1,1-DICHLORO-2-PROPANONE 99% 0.0072 0.0001

1,1,1-TRICHLORO-2-PROPANONE 96% 0.0082 0.0003

GIARDIA LAMBLIA (see Cyst) 99.99%

HEPTACHLOR* >99% 0.25 0.00001

HEPTACHLOR EPOXIDE* 98% 0.0107 0.0002

HEXACHLOROBUTADIENE
(Perchlorobutadiene)*

HEXACHLOROCYCLOPENTADIENE* >99% 0.060 0.000002

LEAD pH 6.5 99% 0.15 +/- 10% 0.010

LEAD pH 8.5 99% 0.15 +/- 10% 0.010

LINDANE* >99% 0.055 0.00001

METHOXYCHLOR* >99% 0.050 0.0001

METHYLBENZENE (see TOLUENE)* >99% 0.078 0.001

MONOCHLOROBENZENE
(see CHLOROBENZENE)*

PCE (see TETRACHLOROETHYLENE)* >99% 0.081 0.001

PENTACHLOROPHENOL* >99% 0.096 0.001

PERCHLOROBUTADIENE
(see HEXACHLOROBUTADIENE)*

PROPYLENE DICHLORIDE
(see 1,2 -DICHLOROPROPANE)*

SIMAZINE* >97% 0.120 0.004

SILVEX (see 2,4,5-TP)* 99% 0.270 0.0016

STYRENE (Vinylbenzene)* >99% 0.15 0.0005

1,1,1-TCA
(see 1,1,1 - TRICHLOROETHANE)*

TCE (see TRICHLOROETHYLENE)* >99% 0.180 0.0010

1,1,2,2- TETRACHLOROETHANE* >99% 0.081 0.001

TETRACHLOROETHYLENE* >99% 0.081 0.001

TOLUENE (Methylbenzene)* >99% 0.078 0.001

TOXOPLASMA

2,4,5-TP (Silvex)* 99% 0.270 0.0016

TRIBROMOACETIC ACID* 0.042 0.001

1,2,4 TRICHLOROBENZENE (Unsymtrichlorobenzene)* >99% 0.160 0.0005

1,1,1-TRICHLOROETHANE (1,1,1-TCA)* 95% 0.084 0.0046

1,1,2-TRICHLOROETHANE* >99% 0.150 0.0005

TRICHLOROETHYLENE (TCE)* >99% 0.180 0.0010

TRIHALOMETHANES (TTHM) (Chloroform; Bromoform;
Bromodichloromethane; Dibromochloromethane)

Unsym-Trichlorobenzene (see 1,2,4­TRICHLOROBENZENE)*

Vinylbenzene (see STYRENE)* >99% 0.150 0.0005

XYLENES (TOTAL)* >99% 0.070 0.001

Percent

Reduction

>98% 0.044 0.001

>99% 0.077 0.001

>98% 0.044 0.001

>99% 0.080 0.001

95% 0.084 0.0046

>99.8% 0.300 +/- 0.30 0.015

>99% 0.160 0.0005

Inuent Challenge

Concentration

(mg/L unless noted)

minimum 50,000/mL 99.95%

minimum 50,000/mL 99.95%

minimum 50,000/mL 99.95%

Maximum Permissible

Product Water
Concentration

11

Performance Data Sheet

Watts Premier Inc.

8716 W Ludlow Drive Suite #1

Peoria, AZ 85381 USA

WP-2 BVC

GENERAL USE CONDITIONS:

1: System has been independently tested for the removal of microbiologically contaminated water. The system is not intended
for the treatment of water that has an obvious contamination source, such as raw sewage. This system is not intended to
convert wastewater to microbiologically safe drinking water.
2: Operating Temperature: Maximum 100o F (37.8o C) Minimum 40o F (4.4o C)
3: Operating Water Pressure: Maximum 85-psi (5.98 kg/cm2) Minimum 20-psi
4: Maximum ow Rate: 0.50 gpm (1.89 lpm)
5: Rated Capacity: 2000 Gallons (7,500 liters)

RECOMMENDED REPLACEMENT PARTS AND CHANGE INTERVAL:

Note: Depending on incoming feed water conditions replacement time frame may vary.
Description Part Number Change Time Frame Cost
Stage 1: sediment: 5M-10 104017 6 Months $ 3.50*
Stage 2: Microbiological Carbonblock 101003 6 Months $33.95*

*All prices subject to change without notice

This system has been tested according to NSF/ANSI Standard 42 for the reduction of the substances listed below. The concentration of the indicated
substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as
specied in NSF/ANSI 42. Testing performed under standard laboratory conditions, actual performance may vary.

Contaminant Inuent Challenge Concentration Percent Reduction Achieved

Chlorine Taste & Odor 2.0 mg/L + 10% 98%
Bacteria* 99.9999%
Virus* 99.99%
Cyst* 99.95%

* Independently tested and veried by BioVir Laboratories
These substances are not necessarily in your drinking water.

Refer to the owners manual for further maintenance requirements and warranty information. System must be maintained according to
manufacturers use instructions, including replacement of lter elements.

System has been tested by Bio Vir as a Microbiological
Water Puriers based on the recommendations set forth in
the USEPA Guide Standard and Protocol for Microbiological
Water Puriers (OPP Task Force Report, 1987).

Questions? Contact Watts Premier 800-752-5582 www.premierH2o.com
480-675-7995

12

13

Other Products from Watts Premier

Watts Premier has other ne water ltration products and accessories to enhance your water and to
compliment your water ltration system. Listed on this page are only a few of the items we offer. Visit
our web site at www.premierH2o.com or call our Customer Service Representatives at
1-800-752-5582 (inside USA) 1-480-675-7995 (outside USA) for more products.

Watts Premier Ice Maker Filter Kit - High efciency replaceable lter that
can last up to 5 years or 20,000 gallons. Perfect for residential and com­mercial ice makers as well as refrigerators, drinking fountains, coffee & tea
brewers, motor homes and campers. Reduces chlorine taste and odor.

Part No. 500327 *$36.95/ea

Whole House Filter

Great for sediment problems such as in well water supply or areas where dirt
and rust particles are a problem. Includes three 50 micron sediment lters
and wrench
(3/4” ports)

Part No. 500223 *$42.95/ea
Replacement lter

Part No. 304007 *$ 4.50/ea

Watts Premier Hot Water Recirculation System

Bring convenience and savings to your home, giving you hot water instantly
at every faucet, when you need it. This unique product is easy to install and
not only provides you with the convenience of hot water when you need it, but
saves an average of over 15,000 gallons per year.

Part No. 500800 *$229.99/ea

Pool Doc Pool & Spa Water Tester

PoolDocTM accurately measures pool and spa chemistry and provides
instructions on how to bring the pool/spa back into balance.

Part No. 164040 *$189.99/ea

One Piece Manifold 5-Stage Reverse Osmosis WP-5

This state of the art manifold reverse osmosis system provides a seamless
water path eliminating 17 connections from standard style units. Includes
carbon block technology and high production 24gpd Thin Film Membrane

- NSF Certied for the reduction of a wide range of contaminants including:
Arsenic, Chromium, Perchlorate, Lead, Radium, and many others.

Part No. 500023 *$239.00/ea

*All prices subject to change without notice.

14

WARRANTY REGISTRATION

Thank you for selecting Watts Premier for your water ltration needs.

4 Ways to Register

1. On-line at www.premierH2o.com

Register your product on-line and receive a 5% discount on your next on-line order, Plus receive reduced shipping.

2. Call in your information 1-800-752-5582

Call and we will enter your registration information for you.

3. Fax in your information 623-866-5666

Fax this form directly to us.

Registering will

insure you

receive Watts

FREE

4. Mail in the information.

Please complete the form below. Mail to: Watts Premier

8716 W Ludlow Drive Suite #1
Peoria, AZ 85381

Watts Premier Inc. is concerned for the safety of your personal information. Watts Premier collects personal information when you register
with Watts Premier. This information is stored in our data base and we do not rent, sell, or share personal information with other people
or nonafliated companies. We reserve the right to send you certain types of communications such as direct mail, email, or by telephone
relating to our products or products that you have purchased. We limit access to your personal information to those employees who will
directly provide you with services or products in order to do their jobs. We want to offer you four ways to communicate with us. 1.Online,

2.Fax, 3.Telephone, and 4. Mail the form below. By registering your product you will receive the full benet of our warranty. Watts Premier
will also send you a semiannual lter change reminder beginning six months from date of installation. To insure the highest quality of your
water, lters should be replaced every 6 months. If you have any questions or comments please give us a call at 1-800-752-5582 M-F
8:00am -5:00pm MST.

First Name:_________________________ Last Name:____________________________

Address: ________________________________________ City: ____________________

Filter

Reminder

Notice

State: _______________________________________ Zip Code: ___________________

Country: USA CANADA MEXICO OTHER ____________

Phone # ______-__________ -__________ Email Address: ______________________

Date of Purchase: ___________________ Date of Install: _______________________

Installed By: SELF Plumbing Professional Where Purchased: ____________

Model Number: _______________________ Serial Number: ____ - __________

Watts Premier, Inc. 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381
Phone: [phone] www.premierH2o.com Fax: [phone]

15

XXXXX

XXXXXX

-

WARRANTY REGISTRATION

Please Fill out and keep for your Records

First Name:_________________________ Last Name:____________________________

Address: ________________________________________ City: ____________________

State: _______________________________________ Zip Code: ___________________

Country: USA CANADA MEXICO OTHER ____________

Phone # ______-__________ -__________ Email Address: ______________________

Date of Purchase: ___________________ Date of Install: _______________________

Installed By: SELF Plumbing Professional Where Purchased: ____________

Model Number: _______________________ Serial Number: ____ - __________

XXXXX

Iowa Department of Public Health - Sales in Iowa require this to be completed, signed and returned.
These signatures will be retained on le for two years.

Insert into envelope and return to Watts Premier

Watts Premier
8716 W Ludlow Drive Suite #1
Peoria, AZ 85381

XXXXXX

-

16

Removing chlorine from your shower

Special Chlorgon & KDF media – More effective then carbon medias with

hot water applications in the removal of the following.

√ Free Chlorine (CL-)
√ Combined Chlorine (Sodium Hypochlorite)
√ Hydrogen Sulde (Rotten egg smell)
√ Plus, its pH balanced.

Deluxe Shower Handle with Built in Filter Replacement lters 2PK
5-Way Massaging Spray
72” Reinforced Hose
High Strength Bracket
Triple Plated Finish
Reversible Filter Cartridge (Model HHC)
Cartridge Life Rating: 3 months

Part No. 107070 WHITE *$38.95
Part No. 107091 CHROME *$44.95
Part No. 107092 GOLD *$44.95

Shower Falls Deluxe Shower Handle with Built in Filter

Curved Ergonomic Shower Handle Replacement lters 2PK
Filter Handle Extension
Dual Swivel Adjustment
Ultra Deluxe 5 Way Massaging Spray
72” Reinforced Hose
Chrome Plated Brass Bracket & Swivel Ball Extension
Triple Plated Finish
Reversible Filter Cartridge (Model HHC)
Cartridge Life Rating: 3 months
Part No. 107095 CHROME *$55.95

√ Iron oxide (rust water)
√ Dirt, sediment
√ Odors

Part No. 107075 *$15.95/pk

Part No. 107075 *$15.95/pk

All-In-One reversible High-Flow Filter Replacement lter

Deluxe 5-Way Massaging Spray

Soft-Touch Adjustment Pads

Anti-Scaling Spray Nozzle
High Strength Housing
Triple Plated Finish
Cartridge Life Rating: 6 months

Part No. 107098 White/Chrome *$39.95 Part No. 107080 *$13.95/ea

*All prices subject to change without notice.

17

8716 W Ludlow Drive Suite #1 Peoria, AZ 85381

Limited Warranty

What your Warranty Covers:

If any part of your WATTS PREMIER WP-2 is defective in workmanship (excluding replaceable lters ), return unit after
obtaining a return authorization (see below), within 3 years of original retail purchase, WATTS PREMIER will repair or, at
WATTS PREMIER’S option, replace the system at no charge.

How to obtain Warranty Service:

For warranty service, call 1-800-752-5582 for a return authorization number. Then, ship your unit to our factory, freight and
insurance prepaid, with proof of date of original purchase. Please include a note stating the problem. Premier will repair it,
or replace it, and ship it back to you prepaid.

What this warranty does not cover:

This warranty does not cover defects resulting from improper installation, (contrary to WATTS PREMIER’S printed
instructions), from abuse, misuse, misapplication, improper maintenance, neglect, alteration, accidents, casualties, re,
ood, freezing, environmental factors, water pressure spikes or other such acts of God.
This warranty will be void if defects occur due to failure to observe the following conditions:

1. The WP-2 System must be hooked up to a potable municipal or well cold water supply.

2. The pH of the water must not be lower than 5 or higher than 10.

3. The incoming water pressure must be between 20 and 85 pounds per square inch.

4. Incoming water to the Counter Top cannot exceed 100 degrees F (38 degrees C.)

This warranty does not cover any equipment that is relocated from the site of its original installation.

This warranty doe not cover any charges incurred due to professional installation.

This warranty does not cover any equipment that is installed or used outside the United States of America and Canada.

LIMITATIONS AND EXCLUSIONS:

WATTS PREMIER WILL NOT BE RESPONSIBLE FOR ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. WATTS PREMIER WILL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING TRAVEL EXPENSE, TELEPHONE CHARGES, LOSS OF REVENUE, LOSS OF TIME,
INCONVENIENCE, LOSS OF USE OF THE EQUIPMENT, AND DAMAGE CAUSED BY THIS EQUIPMENT AND ITS FAILURE TO
FUNCTION PROPERLY. THIS WARRANTY SETS FORTH ALL OF PREMIER’S RESPONSIBILITIES REGARDING THIS EQUIPMENT.

OTHER CONDITIONS:

If WATTS PREMIER chooses to replace the equipment, WATTS PREMIER may replace it with reconditioned equipment. Parts used in
repairing or replacing the equipment will be warranted for 90 days from the date the equipment is returned to you or for the remainder of
the original warranty period, whichever is longer. This warranty is not assignable or transferable.

YOUR RIGHTS UNDER STATE LAW:

Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply. This warranty gives you specic legal rights,
and you may have other legal rights which vary from state to state.

18