Watts LFB6001 User Manual

For Commercial and Industrial Applications
ES-LFB6000
Job Name
Job Location
Engineer
Approval  
LEAD FREE
–––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
*
Series LFB6000, LFB6001
2-Piece, Standard Port, Lead Free* Ball Valves
Sizes: 1⁄4" – 4" (8 – 100mm)
Series LFB6000, LFB6001 2-Piece, Standard Port, Lead Free* Ball Valves feature a blowout proof pressure retaining 316 stainless steel stem. The LFB6000, LFB6001’s standard port orifice ensures minimal pressure drop, while Durafill stainless steel ball provide lasting service for a wide range of liq­uids and gases. The Series LFB6000 and LFB6001 feature Lead Free* construction to comply with Lead Free* installation require­ments.
Features
•   Lead Free copper silicon alloy body and adapter
•  316 stainless steel ball & stem
•   Durafill
•   Blowout proof, pressure retaining 316 stainless steel stem
•   
•   High cycle life reinforced PTFE stem packing seal and thrust 
•   Vinyl insulator on heavy duty, zinc-plated, carbon steel handles
•   Quarter-turn open or close operation
•   Low operating torque 
•   Adjustable stem packing gland
•   Each valve factory tested 
®
(carbon/glass filled PTFE) seats for sizes 1⁄4" – 1⁄2" (8 – 15mm) and 1 (enhanced PTFE) seats for sizes ing service for a wide range of liquids and gases
1
4" – 3" (8 – 80mm) pressure rated at 600psi (41 bar) WOG non-shock; 150psi (10 bar) WSP. 4" (100mm) pressure rated at 400psi (28 bar) WOG non-shock; 125psi (8.6 bar) WSP (over 150psi steam requires SS trim)
washer
1
4" – 4" (32 – 100mm) and Uniseal®
®
and Uniseal® seats and 316
3
4" & 1" (20 & 25mm) for last-
Contractor
Approval  
Contractor’s P.O. No.
Representative
––––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––
LFB6000
Pressure – Temperature
Temperature Range: 0°F – 450°F (-18°C – 232°C) @ 50psi (3.4 bar)
Pressure Range:
1
4" – 3" (8 – 80mm),
600psi (41 bar) WOG non-shock; 150psi (10 bar) WSP
4" (100mm), 400psi (28 bar) WOG non-shock; 125psi (8.6 bar) WSP
Specifications
A 2-piece standard port Lead Free* copper silicon alloy ball valve 
to be installed as indicated on the plans. The valve must have a blowout proof pressure retaining 316 stainless steel stem, Durafill
1
4" – 1⁄2" & 11⁄4" – 4") or Uniseal® seats (3⁄4" & 1"), reinforced 
seats ( PTFE stem packing seal, and 316 stainless steel ball. Valves with
top loaded stems or valves without adjustable packing are not 
acceptable. Pressure rating no less than 600psi (41 bar) WOG non-shock; 150psi (10 bar) WSP for WOG non-shock; 125psi (8.6 bar) WSP for 4". The valve shall be constructed using Lead Free* copper silicon alloy. Lead Free* ball valves shall comply with state codes and standards, where appli­cable, requiring reduced lead content. Valve must conform to MSS-SP-110 and shall be a Watts Series LFB6000 (threaded) or LFB6001 (solder).
Durafill® is a registered trademark of Cargill, Limited. Uniseal® is a registered trademark of Uniseal, Incorporated.
* The wetted surface of this product contacted by consumable water
contains less than 0.25% of lead by weight.
1
4" – 3" and 400psi (28 bar)
LFB6001**
®
Models
LFB6000 1⁄4" – 4" (8 – 100mm) threaded NPT end connections
3
LFB6001
8" – 3" (10 – 80mm) solder end connections**
Options
LH – Locking lever handle
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with­out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
**This valve is designed to be soft soldered into lines without disas­sembly, using a low temperature solder 420°F (216°C). Other solders such as 95/5 tin antimony 460°F (238°C) or 96/4 tin silver 420°F (216°C) can be used, however extreme caution must be used to pre-
vent seat damage. Higher temperature solders will damage the seat  material. ANSI B.16.18 states that the maximum operating pressure 
of 50-50 solder connections is 200 psi (14 bar) at 100°F (38°C) and decreases with higher temperatures.
Apply heat with the flame directed AWAY from the center of the valve body. Excessive heat can harm the seats. After soldering, the packing 
nut may have to be tightened.
Materials
gpm lpm
A
B
C
D
G
E
F
A Handle Nut Zinc Plated Carbon Steel B Handle   Zinc Plated Carbon Steel with Vinyl Insulator C Packing Nut  Brass ASTM B16, C36000 D Stem Packing Glass Reinforced PTFE E Thrust Washer Glass Reinforced PTFE F Stem 316 Stainless Steel G Body Lead Free* copper silicon alloy H Seats Durafill
Uniseal
® (1
4" – 1⁄2" & 11⁄4" – 4")
® (3
4" & 1")
I Ball 316 Stainless Steel J Adapter Lead Free* brass K Body Seals PTFE (1
Dimensions
— Weights
1
4" – 4" only) - Not shown
H
C
I
H
I
H
J
Valve Seat Rating
bar psi
41 600
34 500
28 400
21 300
Pressure
14 200
7 100
3 50
1
4" – 3" (8 – 80mm)
4" (100mm)
100 200 300 400 500 °F 38 93 149 204 260 °C
Temperature
Pressure Drop vs. Flow
kPa psi 138 20
69 10 55 8 41 6
28 4
21 3
14 2
71.0
5.5.8
4.1.6
Pressure Drop
2.8.4
2.1.3
1.4.2
J
.7 .1
28
14
311
Virgin PTFE
415
4" with
623
SIZE CV OPERATING (DN) RATING TORQUE
In. mm in./lbs. Nm
1
4 8 6 60 6.8
3
8 10 6 60 6.8
1
2 15 15 60 6.8
3
4 20 25 90 10.2
1 25 40 150 16.9
1
1
4 32 50 175 19.8
1
1
2 40 75 200 22.6
2 50 110 250 28.2
1
2
2 65 260 500 56.5 3 80 400 600 67.8 4 100 450 800 90.4
" (8-10 mm)
8
3
" (15mm)
"-
2
4
1
1
40 152
30 114
20 76
10 38
830
" (32mm)
" (40mm)
4
2
" (20mm)
4
3
60 228
1
1
1
1
1" (25mm)
200 760
100 380
80 304
2" (50mm)
300 1140
400 1520
600 2280
" (65mm)
2
1
2
800 3040
3" (80mm)
1000 3800
4" (100mm)
2000 7600
Flow
LFB6000
E
*
L
SIZE DN DIMENSIONS WEIGHTS
C E H I J L ** Center to Radius of Dia. Solder Depth Solder Handle Center to End Handle Ball Orifice Connection End to End Connection
in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm lbs. kg.
1
4 8 13⁄4 45 11⁄16 27 33⁄4 78 3⁄8 10 - - 21⁄16 52 - - 0.6 0.3
3
8 10 13⁄4 45 11⁄16 27 33⁄4 78 3⁄8 10 - - 21⁄16 52 - - 0.6 0.3
1
2 15 13⁄4 45 11⁄16 27 33⁄4 95 1⁄2 13 - - 21⁄4 58 - - 0.6 0.3
3
4 20 2 51 17⁄16 36 33⁄4 95 11⁄16 17 - - 213⁄16 72 - - 1.0 0.5
1 25 2
1
1
4 32 21⁄2 64 115⁄16 49 313⁄16 97 1 25 - - 37⁄8 99 - - 2.2 1.0
1
1
2 40 3 76 21⁄8 54 51⁄2 140 11⁄4 32 - - 41⁄4 108 - - 3.2 1.5
2 50 3
1
2
2 65 4 102 33⁄16 81 81⁄8 206 2 51 - - 61⁄2 165 - - 13.2 5.9 3 80 4 4 100 4
1
4 57 111⁄16 43 41⁄2 114 7⁄8 22 - - 37⁄16 87 - - 1.6 0.7
5
16 84 27⁄16 62 51⁄2 140 11⁄2 38 - - 413⁄16 122 - - 4.9 2.2
1
4 108 37⁄16 87 81⁄8 206 21⁄2 64 - - 613⁄16 173 - - 17.5 7.9
13
16 122 37⁄8 98 11 279 3 76 - - 711⁄16 195 - - 29.3 13.3
LFB6001
3
8 10 11⁄2 38 11⁄16 27 33⁄4 95 3⁄8 10 1⁄2 13 25⁄16 58 3⁄8 9 0.5 0.2
1
2 15 13⁄4 44 11⁄16 27 33⁄4 95 1⁄2 13 5⁄8 16 23⁄8 60 1⁄2 13 0.6 0.3
3
4 20 2 51 17⁄16 36 33⁄4 95 11⁄16 17 7⁄8 22 35⁄16 84 3⁄4 19 1.1 0.5
1 25 2
1
1
4 32 21⁄2 64 21⁄4 57 313⁄16 97 1 25 13⁄8 35 41⁄2 114 1 25 2.0 0.9
1
1
2 40 3 76 21⁄2 64 51⁄2 140 11⁄4 32 15⁄8 41 5 127 11⁄16 27 3.3 1.5 2 50 3
1
2
2 65 4 102 311⁄16 93 81⁄8 206 2 51 25⁄8 67 75⁄8 194 17⁄16 36 13.2 6.0 3 80 4
** See Solder Instructions on front.
1
4 57 13⁄4 44 41⁄2 114 7⁄8 22 11⁄8 28 33⁄4 95 7⁄8 22 1.4 0.6
5
16 84 31⁄8 80 51⁄2 140 11⁄2 38 21⁄8 54 61⁄4 159 15⁄16 34 5.2 2.4
1
4 108 41⁄16 103 81⁄8 206 21⁄2 64 31⁄8 80 83⁄16 208 111⁄16 43 15.6 7.1
A Watts Water Technologies Company
USA: Tel: (978) 688-1811 • Fax: (978) 794-1848 • www.watts.com
Canada: Tel: (905) 332-4090 • Fax: (905) 332-7068 • www.watts.ca 
ES-LFB6000 1350 © 2013 Watts
Loading...