Watts FM-BB-20-5 User Manual

w-Max
®
®
Pleated Car
tr
idges
or Reduced Filtr
Pleated Car
Flo
w-Max
or Reduced Filtr
F
idges
tr
Get more filtration for the money with Flow-Max
®
pleated cartridges for high flow, long life, greater
sediment removal and reduced filtration costs.
Flow-Max filter cartridges outperform wound, spun, melt blown, resin bonded and other ”depth” type filter elements because our cartridges are pleated to provide increased surface area and longer life.
Lower pressure drop is another significant advantage, using Flow-Max pleated cartridges, which allows for increased flow rates and the use of smaller filter housings to reduce capital equipment costs.
Further savings are provided because our 100% synthetic filter media is cleanable, five micron and up, to lower cartridge replacement costs.
Flow-Max filter cartridges outperform other pleated elements because our high­performance filter media is systematically produced using 100% synthetic fibers, with no binders or additives to leave a residue, foam or contaminate.
Our filter media is dramatically thicker than other products. For this reason, Flow-Max cartridges provide “depth” filtration for greater sediment removal, along with more surface area with our pleated design.
A multi-ply laminate is
used with our sub and
one micron absolute
grades for longer life and
greater solids removal.
(See right.)
Features
Filter media is pleated for greater surface area.
Synthetic filter media is cellulose-free.
“Thicker” filter media has a greater capacity to capture and retain particles, compared to thin, more rigid media types, which have less void space for particle retention.
One micron absolute and 0.35 media use a multi-ply laminate for superior performance.
Long lengths have netting to hold pleats in place.
All cartridge types and lengths are wrapped.
Full product line (types, lengths & micron ratings).
Benefits
Low pressure drop; long life; reduced filtration costs, compared to wound and spun cartridges.
No additives or binders, which may cause foaming.
Increased dirt holding capacity; longer life; fewer cartridge replacements needed; and reduced filtration costs, compared to other pleated cartridge suppliers.
Increased particle removal efficiency; longer life; and reduced cost per gallon filtered.
Superior performance and appearance.
Provides security at no additional cost.
Greater selection from your single source
supplier!
Flow-Max®cartridges cost less to use . . . regardless what they cost to buy!
Maximum Flow Rates Per Cartridge (GPM)
Micron Rating Standard Cartridge 10” Full-Flow 20” Full-Flow Jumbo Cartridge
9-3/4” 20” 29-1/4” 40 90 170
1 Absolute 3 6 9 8 12 20 40 80
0.35 Micron 4 8 12 9 13 25 50 100 1 Micron 4 8 12 10 15 30 60 120 5 Micron 7 14 21 15 25 50 100 150 20 Micron 8 16 24 15 25 50 100 150 50 Micron 10 20 30 15 25 50 100 150
Note: Filter housing selection should also be considered when flow rate per cartridge is determined.
Lower pressure drop for higher flow rates
Flow-Max®cartridges are pleated, so initial pressure drop is significantly less compared to depth cartridges, such a wound, spun, melt blown and resin bonded. As a result, higher flow rates are possible, reducing filter housing size requirements to lower capital equipment costs.
Depth cartridge
(5 micron)
Flow-Max
®
cartridge
(5 micron)
Use the pressure drop charts shown below to help determine the ideal flow rate for your particular application:
)
Standard cartridges (9-3/4”) Full-Flow (B-B) cartridges Jumbo cartridges
Note: Pressure drop data shown above include filter housing and cartridge.
Flow rates
Maximum flow rate guidelines for Flow-Max cartridges are shown below:
Washable & reusable
Flow-Max®cartridges are washable and reusable, five micron and up to reduce filtration costs. For best results, direct spray into pleats to dislodge sediment. Or, let dry and brush off filter cake from surface of the media.
All Flow-Max
®`
cartridges are individually shrink wrapped for purity
01 2 3 4 5 6 78910
6
5
4
3
2
1
PRESSURE DROP (psi)
FLOW (GPM)
FLOW (GPM)
01 2 3 4 5 6 78910
6
5
4
3
2
1
PRESSURE DROP (psi)
1A
1.0
.9
.8
PRESSURE DROP (psi)
.7
.6
.5
.4
.3
.2
.1
01 2 3 4 5 6 78910
0.35 1
FLOW (GPM
1.0
.9
.8
5
20
50
PRESSURE DROP (psi)
.7
.6
.5
.4
.3
.2
.1
061218 24
FLOW (GPM)
1 Mic. 10"
1 Mic. 20"
5 Mic. 10"
5 Mic. 20"
10
9
PRESSURE DROP (psi)
8
7
6
5
4
3
2
1
050100 150
FLOW (GPM)
1A
0.35
1
5
20
50
Flow-Max®Standard 2-3/4” OD Cartridges
With cellulose-free filter media for water filtration applications
Standard 2-3/4” OD x 9-3/4” length
Product Code Media Type Micron Rating Number Per Case
FM-1A-975 Synthetic 1 Absolute 24 FM-0.35-975 Synthetic 0.35 24 FM-1-975 Synthetic 1 24 FM-5-975 Synthetic 5 24 FM-20-975 Synthetic 20 24 FM-50-975 Synthetic 50 24 FM-100-975 Synthetic 100 24
Standard 2-3/4” OD x 19-1/2” length
Product Code Media Type Micron Rating Number Per Case
FM-1-195 Synthetic 1 24 FM-5-195 Synthetic 5 24 FM-20-195 Synthetic 20 24 FM-50-195 Synthetic 50 24
Standard 2-3/4” OD x 20” length
Product Code Media Type Micron Rating Number Per Case
FM-1A-20 Synthetic 1 Absolute 24 FM-0.35-20 Synthetic 0.35 24 FM-1-20 Synthetic 1 24 FM-5-20 Synthetic 5 24 FM-20-20 Synthetic 20 24 FM-50-20 Synthetic 50 24
Standard 2-3/4” OD x 29-1/4” length
Product Code Media Type Micron Rating Number Per Case
FM-1A-2925 Synthetic 1 Absolute 24 FM-0.35-2925 Synthetic 0.35 24 FM-1-2925 Synthetic 1 24 FM-5-2925 Synthetic 5 24 FM-20-2925 Synthetic 20 24 FM-50-2925 Synthetic 50 24
Standard 2-3/4” OD x 40” length
Product Code Media Type Micron Rating Number Per Case
FM-1-40 Synthetic 1 24 FM-5-40 Synthetic 5 24 FM-20-40 Synthetic 20 24 FM-50-40 Synthetic 50 24
Specifications
Filter media Synthetic (100% cellulose-free) End caps Plastisol (PVC) Center tubes Polypropylene Te mperature range 40°F - 140°F (4.4°C - 60°C) Maximum Pressure 40 PSID Recommended change out 20 - 30 PSID Flow rate per 10” cartridge 3-10 GPM, depending on micron rating
Flow-Max®Full-Flow Cartridges
4-1/2” OD cartridges with cellulose-free filter media for water filtration applications
One micron absolute rated and
0.35 nominal micron cartridges
Ideal for water filtration to remove Cryptosporidium and Giardia cysts. Both grades utilize a multi-ply filter media for greater retention efficiencies and long life.
Full-Flow (B-B) 4-1/2” OD x 9-3/4” length
Product Code Length Media Type Micron Rating Number Per Case
FM-BB-10-1A 9-3/4” Synthetic 1 Absolute 8 FM-BB-10-0.35 9-3/4” Synthetic 0.35 8 FM-BB-10-1 9-3/4” Synthetic 1 8 FM-BB-10-5 9-3/4” Synthetic 5 8 FM-BB-10-20 9-3/4” Synthetic 20 8 FM-BB-10-50 9-3/4” Synthetic 50 8
Note: Cartridges listed above fit in Full-Flow and Big-Blue
®
filter housings.
Full-Flow (B-B) 4-1/2” OD x 20” length
Product Code Length Media Type Micron Rating Number Per Case
FM-BB-20-1A 20” Synthetic 1 Absolute 4 FM-BB-20-0.35 20” Synthetic 0.35 4 FM-BB-20-1 20” Synthetic 1 4 FM-BB-20-5 20” Synthetic 5 4 FM-BB-20-20 20” Synthetic 20 4 FM-BB-20-50 20” Synthetic 50 4
Note: Cartridges listed above fit in Full-Flow and Big-Blue
®
filter housings.
Specifications (synthetic media for sediment)
Maximum temperature 140°F (60°C) Center tubes PVC Minimum temperature 40°F (4.4°C) End caps Molded urethane Maximum pressure 40 PSID Maximum flow rate, model 40 50 GPM (12M3HR) Recommended change out 25-30 PSID Maximum flow rate, model 90 100 GPM (24M3HR) Filter media PE & PP Maximum flow rate, model 170 150 GPM (36M3HR)
Flow-Max®Jumbo Filter Cartridges
With cellulose-free filter media for water filtration applications
Model 40
Standard Synthetic Media Flow-Max jumbo filter cartridge PP Mesh Media
Filter Housing Micron Product Code Product Code Number Per Case
Model Rating with with
Number Synthetic Media Mesh Media
1 Absolute FMHC-40-1A N. A. 1
0.35 FMHC-40-0.35 N. A. 1 1 FMHC-40-1 N. A. 1 5 FMHC-40-5 N. A 1
20 FMHC-40-20 N. A. 1
50 FMHC-40-50 FMJC-40-50M 1 100 FMHC-40-100 N. A. 1 150 N. A. FMJC-40-150M 1
40
Filter Housing Micron Product Code Product Code Number Per Case
Model Rating with with
Number Synthetic Media Mesh Media
1 Absolute FMHC-90-1A N. A. 1
0.35 FMHC-90-0.35 N. A. 1 1 FMHC-90-1 N. A. 1 5 FMHC-90-5 N. A 1
20 FMHC-90-20 N. A. 1
50 FMHC-90-50 FMJC-90-50M 1 100 FMHC-90-100 N. A. 1 150 N. A. FMJC-90-150M 1
90
Model 90
Filter Housing Micron Product Code Product Code Number Per Case
Model Rating with with
Number Synthetic Media Mesh Media
1 Absolute FMHC-170-1A N. A. 1
0.35 FMHC-170-0.35 N. A. 1 1 FMHC-170-1 N. A. 1 5 FMHC-170-5 N. A 1
20 FMHC-170-20 N. A. 1
50 FMHC-170-50 FMJC-170-50M 1 100 FMHC-170-100 N. A. 1 150 N. A. FMJC-170-150M 1
170
Model 170
Flow-Max
®
Phenolic Impregnated Cellulose Cartridges
For Industrial Hot Water & Non-Aqueous Applications
Jumbo Model 170 (7-3/4” x 30-3/4”) for flow rates to 150 GPM
Part Number Model Number Length Micron No. / case
FMPIC-170-5-HT 170 30-3/4” 5 1 FMPIC-170-20-HT 170 30-3/4” 20 1 FMPIC-170-50-HT 170 30-3/4” 50 1
Jumbo Model 90 (7-3/4” x 19-1/2”) for flow rates to 100 GPM
Part Number Model Number Length Micron No. / case
FMPIC-90-5-HT 90 19-1/2” 5 1 FMPIC-90-20-HT 90 19-1/2” 20 1 FMPIC-90-50-HT 90 19-1/2” 50 1
Applications
High temperature industrial water filtration
Lubricating oil
Cutting fluids
Solvents
Distillate fuel
Fuel oil
Hydraulic fluids
Specifications Data
Maximum temperature 250˚F (121˚C) Minimum temperature -20˚F (-29˚C) Maximum pressure 70 PSID (482 k PA) Recommended change out 25 PSID (172 k PA) Media Phenolic impregnated cellulose End caps, cores, outer body Electro plated tin
Jumbo Model 40 (7-3/4” x 9-5/8”) for flow rates to 50 GPM
Part Number Model Number Length Micron No. / case
FMPIC-40-5-HT 40 9-5/8” 5 1 FMPIC-40-20-HT 40 9-5/8” 20 1 FMPIC-40-50-HT 40 9-5/8” 50 1
Note: Jumbo 40. 90 and 170 cartridges listed above fit in Flow-Max housings only. Phenolic impregnated cellulose cartridges are not cleanable or reusable; and they are not suitable for potable water.
Flow-Max®HP Series Cartridges
100% polypropylene construction with efficiencies to 99.98%.
High efficiency pleated cartridges
Flow-Max HP series cartridges are cost efficient, disposable filter elements for a wide range of applications. Constructed entirely of polypropylene, they are ideally suited for critical filtration, including high purity water and aggressive chemicals.
Applications
High purity water
Pre-filtration for RO
Plating solutions
Inks
Bottled water
Rinse water for electronics
Edible oils
Traps for DI resin
Product codes
Initial pressure drop per 10” cartridge
Part Number Micron Length End Cap Number / Case Ship Wt. (lbs.)
FPP-0.2-975-DOE 0.2 9-3/4” DOE 24 12 FPP-0.2-20-DOE 0.2 20” DOE 12 11 FPP-0.2-30-DOE 0.2 30” DOE 12 17 FPP-0.2-40-DOE 0.2 40” DOE 12 21
FPP-0.2-10-222 0.2 10” 222 / Flat 24 12 FPP-0.2-20-222 0.2 20” 222 / Flat 12 11 FPP-0.2-30-222 0.2 30” 222 / Flat 12 17 FPP-0.2-40-222 0.2 40” 222 / Flat 12 21
FPP-0.2-10-222F 0.2 10” 222 / Fin 24 12 FPP-0.2-20-222F 0.2 20” 222 / Fin 12 11 FPP-0.2-30-222F 0.2 30” 222 / Fin 12 17 FPP-0.2-40-222F 0.2 40” 222 / Fin 12 21
FPP-1-975-DOE 1 9-3/4” DOE 24 12 FPP-1-20-DOE 1 20” DOE 12 11 FPP-1-30-DOE 1 30” DOE 12 17 FPP-1-40-DOE 1 40” DOE 12 21
FPP-1-10-222 1 10” 222 / Flat 24 12 FPP-1-20-222 1 20” 222 / Flat 12 11 FPP-1-30-222 1 30” 222 / Flat 12 17 FPP-1-40-222 1 40” 222 / Flat 12 21
Additional micron ratings and types are available. Please inquire.
Distributed by:
MADE IN U.S.A.
5
4
3
P. S . I.
2
1
1 2 3 4 5 6 7 8 9 10
Gallons Per Minute
Micron
0.2
0.45
1
5 10 25 50
Flow-Max® Filters
Loading...