Watts EW-AUS5001 User Manual

Energy saving made simple

MONITOR•CONTROL•SAVE

Energy Watch Monitor

Monitor household electricity use and cost in real time

Instruction Manual

EW-AUS5001

Your package contains all of the elements shown below. If any item is missing, please contact
your installer immediately.

Parts and UsageWhat elements does your package contain?

Reading the display

Top display

This number refers to how long the appliance has been
connected to the meter. To restart the timer press [ Re-

set4 ].

Middle display

A re ading of volts ( V), amps (A), wa tts (W ) or k ilowatt
hours (kWh) de pending on what function is sel ected.
The func tion selec ted is determine d by the symbol
shown und er the number.

Lower display

This display changes depending on what function is chosen.

Energy Watch Monitor

Extension Cord

Cost

button3

Functio n

button2

NOTE:

NOTE

Battery back-up: There is a 3.6V rechargeable battery installed inside the ENERGY Watch

Monitor. It allows for the storage of data when the meter is not plugged in.

Reset

button4

Up butto n

5

Down

button6

How to use the ENERGY Watch Monitor?

Plug the meter into a power outlet and then plug an appliance or power board into the
ENERGY Watch Monitor. The ENERGY Watch Monitor’s functions can be selected by pressing
the [ Function 2]. [ Cost 3] is a shortcut to the time / cost function.

To set the cost, hold down [ Cost 3]. Blinking numbers indicate the cost is ready to be
changed. Use [ Function 2] to navigate between the dollars and cents and use [ 5]
and [ 6] to select gures. Press [ Cost 3] when nished.

To clear the readings from a previous appliance, press [ Reset 4] (with the point of a pen

Instruction Manual

or pencil). This will also re-start the timer. [ Reset 4] can also be used to clear the meter if
an abnormal display appears on the screen or if the meter is not responding.

Unplug the ENERGY Watch Monitor and it will turn o automatically.

2 3

Navigating the functions Navigating the functions

Display Modes

If left for 1 minute the power meter will revert to ‘Time / Watts / Cost’ mode. To switch modes,
press the [ Function button2]. Please note: ‘kWh’ and cost data will not accumulate when
consumption is below ~2.5 watts.

Time / Watts / Cost (Fig.1)

Top display: This number refers to how long the appliance has been plugged into the

power meter. The time does not automatically reset when the appliance is unplugged.
To restart the timer press [ Reset button4].

Middle display: This is an instantaneous reading of how many watts the appliance is

using.

Lower display: This shows you the cost of running an appliance over time. Cost can only

be calculated after the cost is set (see previous page).

Fig.1

Kilowatt Hours (Fig.2)

Middle display: This is a cumulative reading of kilowatt hours (kWh) that the appliance

has used over the time shown in the top display.

Lower display: The number of days that the appliance has been plugged into the power

meter.

Voltage / Frequency (Fig.3)

Middle display: Voltage reading in Volts.
Lower display: Frequency reading in Hertz.

Fig.2

Amps / Power Factor (Fig.4)

Middle display: Current reading in Amps.
Lower display: This is an instantaneous

reading of the Power Factor.

Fig.3 Fig.4

Maximum Wattage (Fig.6)

Middle display: This number refers to the

highest power consumption (in watts) of
an appliance since the last reset (the lower
display reads ‘Hi’).

Time / Cost (Fig.7)

Middle display: Blank.
Lower display: Cost / kWh (you can entre as

either $00.00 or 00.00 cents).

Fig.6 Fig.7

Data Clearance

Press and hold down the [ 5] and [ 6] buttons until the display starts to ash.
Press these buttons again for 3 seconds until the display stop ashing. All cumulative data
will be erased.

Minimum Wattage (Fig.5)

Middle display: This number refers to the lowest power consumption (in watts) of an

appliance since the last reset (the lower display reads ‘Lo’).

Fig.5

4 5

How do I use the Energy Monitor?

The extension cord helps you to access the wall outlet behind any cabinet or at very low level
of the wall easily. By using the extension cord with our plug in monitor, you have no dicul­ties on monitoring your appliances anywhere.

4

1. Connect the extension cord to the Energy Watch Monitor.

2. Plug the extension cord to the wall outlet (This can be any outlet which is dicult to reach).

3. Connect the equipment you wish to use to Energy Monitor.

4. Turn on your electric appliance.

5. You can read the result though the display.

5

3

1

2

IMPORTANT SAFETY NOTES

IMPORTANT: Please retain your instruction manual for future use.

Watts Clever believes that the safe performance of your product is the rst priority. We ask
that any electrical appliance that you use be operated in a sensible fashion with due care and
attention placed on the following points:

• Carefully read all instructions before operating the Energy Watch Monitor for the rst time
and save for future reference.

• To protect against electric shock, do not immerse the Energy Watch Monitor in water or
any other liquid.

• Do not insert needles or any other metal objects into the socket holes.

• Avoid moisture, extreme temperatures, shock and vibration.

• Do not exceed the maximum load of 10A / 2400W either with a single appliance or with a
group of appliance connected via a power strip.

• Do not connect 2 or more Energy Watch Monitor together.

• For indoor use only.

• Always ensure the plug of any appliance is inserted fully into the Energy Watch Monitor.

6 7

Product Specications

Model • EW-AUS5001 | CAT Number • MS6119

Dimensions • 159 (L) x 72.7 (W) x 37.5 (H) mm (not include the plug)

Operating voltage • 240V AC | Frequency display • 50Hz

Operating current • max 10A | Wattage display (watts) • 0W - 2400W

Current display (amps) • 0.0A - 10.0A

Price display range • 0.00$ / kWh - 99.99$ / kWh

Total kWh and cost display • 0.000kWh - 9999kWh

SAA Approval : SAA110782

N287 Z752

Made in China

For product support, please visit

http://support.wattsclever.com

For further assistance please contact us on

[e-mail]

© 2013 Watts Clever All Rights Reserved

http://www.wattsclever.com http://support.wattsclever.com

Distributed by:

Electus Distribution Pty Ltd
320 Victoria Road Rydalmere,
NSW 2116 Australia
Tel: [phone]
Fax: [phone]
www.electusdistribution.com.au

Due to continual improvement in design or otherwise,

the product you purchase may dier slightly from the illustration in this book