Watts CWS150 User Manual

For Commercial Applications
ES-WQ-CWS150
Job Name
Job Location
Engineer
Approval
–––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––
Contractor
Contractor’s P.O. No.
Representative
Series CWS150
Commercial Water Softening Systems
Connection Size: 1 Flow Rates: Up to 68 gpm (257 lpm)
Watts CWS150 water softening systems are highly efficient cation exchange type water softeners. They are suitable for commercial applications ranging from 40,000 to 300,000 grains of hardness removal and flow rates up to 68 (257 lpm) gallons per minute. Regeneration is meter demand initiated. All cycles of regeneration are fully automatic and do not require manual actuation.
Watts CWS150 water softeners are designed for point of use or point of entry applications where the benefits of softened water are required. These systems exchange scale forming calcium and magnesium ions with non-scale forming sodium ions to create soft water for a variety of applications. Steam boiler make up water, water heater pretreatment, reverse osmosis pretreatment, sterilizer make up water, washing, and process water are all common appli­cations for the Watts CWS150 water softeners.
Softened water provides a wide variety of benefits from not intro­ducing scale into pipes, valves, water heating equipment, heat exchangers, and cooling towers to reducing mineral build up in areas that see excessive splashing such as food prepara-tion counters and sink areas. Softened water also conserves soaps and cleaning agents by eliminating the formation of soap curd, so your cleaners can work on cleaning not reacting with the hardness in your water.
Features
• Third party tested fully automatic metered demand control valve
• Sophisticated digital electronic controls that store operating
history that can be accessed by the user
• Fully adjustable regeneration cycles
• Durable lead free brass bodied control valve for years of service
• Input for remote signal regeneration initiation
• WQA Certified high capacity resin
• Highly corrosion resistant NSF Certified fiberglass tanks
• Durable polypropylene lower distribution system
Standards
Control Valve- Third party tested to NSF/ANSI Std. 61 Ion Exchange Resin- WQA Certified to NSF/ANSI Std. 44 Mineral Tank- NSF Certified to ANSI Std. 44 or 61
1
/2" (40 mm)
––––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––
Series CWS150
Specifications
A Watts CWS150 water softening system shall be installed on
the building’s main water line just after it enters the building. The
installation point shall be after any backflow prevention or pressure regulating valves. Other installation options are to install a system
just before the water heater or other types of equipment needing the protection of softened water. In installations where dedicated
cold water make up to a water heater is the installation point, a backflow preventer and a thermal expansion tank must be installed as well. The system shall be installed with a bypass valve to allow for the shut down and removal of the unit without interrupting the water supply to the building. The water softener shall be a down flow regenerated, metered demand, sodium cycle cation exchange type system with all components necessary for proper opera­tion. Electrical requirements are 120 volt 60 hertz. A local drain is required to accept drain water from the system. The feed water pressure must not fall below 25psi or exceed 125psi. Water tem-
perature must not fall below 34°F or exceed 110°F (1 - 43°C). The
system shall provide softened water measuring less than one grain per gallon of hardness as Calcium Carbonate when operated within the resin manufacturer’s operational specifications.
Note: Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system.
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with­out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
Feed Water Guidelines
pH ....................... 6 to 10
Hardness (maximum) ......... Depends on customers acceptable
hardness leakage level.
Water Pressure ............. 25psi to 125psi (171 kPa to 8.5 bar)
Temperature ............... 34 - 110°F (1 - 43°C)
Free Chlorine (maximum) ...... 1mg/L
Iron (maximum) ............. 1mg/L
Oil and H2S ................ None Allowed
Turbidity .................. Less than 5.0 NTU
Dimensions - Weight
For all other guideline information please contact your Watts representative.
Note: Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system.
CwS150 SerieS
oVerall oVerall oVerall MoDel Tank in ouT HeigHT DePTH wiDTH Brine Tank
M4410W 12"X52" 56.3" 56.3" 63.3" 13.0" 16.7" 18"X40"
M4414W 14"X65" 68.4" 68.4" 74.3" 14.1" 17.8" 18"X40" M4418W 16"X65" 67.8" 67.8" 73.7" 16.1" 18.7" 18"X40" M4422W 18"X65" 70.3" 70.3" 76.2" 18.1" 20.8" 24"X41" M4426W 21"X62" 70.1" 70.1" 76.1" 21.1" 21.2" 24"X41" M4430W 24"X72" 77.3" 77.3" 83.2" 24.1" 24.1" 30"X50"
Specifications
Mineral Tank Brine Tank SofTening lBS. SalT Per flow raTe & PreSSure Tank reSin graVel Tank SalT CaPaCiTY regeneraTion SerV DroP Bkw MoDel SiZe ft
3
#20 SiZe fill Max Min Max Min gPM PSi gPM
M4410W 12x52 2.0 30 lbs. 18x40 400 60 K 40 K 30 12 28/38 15/25 4.0 M4414W 14x65 3.0 60 lbs. 18x40 400 90 K 60 K 45 18 33/44 15/25 5.0 M4418W 16x65 4.0 80 lbs. 18x40 400 120 K 80 K 60 24 36/50 15/25 7.0 M4422W 18x65 5.0 100 lbs. 24x41 600 150 K 100 K 75 30 40/54 15/25 11.0 M4426W 21x62 7.0 100 lbs. 24x41 800 210 K 140 K 105 42 43/58 15/25 13.0 M4430W 24x72 10.0 200 lbs. 30x50 1400 300 K 200 K 150 60 45/60 15/25 15.0
Note: Capacities are based on resin manufacturer’s data and are dependent upon influent water TDS, temperature, bed depth, and flow rates. Feed water must be free of oil and color. Pipe size, tank size, and space requirements are in inches. Capacities and flow rates expressed above are per tank. Flow rates listed at 25psi drops are for intermittent peak flow rates and are not to be used as continuous flows.
Note: Flow rates listed above are based on pressure drop only. Selecting a system based on pressure drop alone does not guarantee that
the system will proved adequately softened water. System selection should be based on resin quantity, capacity required, feed water analy­sis, and application requirements.
Ordering Information
MoDel DeSCriPTion PiPe SiZe SPaCe reQuireD weigHT lBS kgS
M4410W A0060FM150WE with turbine flow meter 1.5" 24 x 44 x 75 210 95 M4414W A0090FM150WE with turbine flow meter 1.5" 24 x 44 x 87 240 109 M4418W A0120FM150WE with turbine flow meter 1.5" 24 x 44 x 87 320 145 M4422W A0150FM150WE with turbine flow meter 1.5" 24 x 50 x 87 380 172 M4426W A0210FM150WE with turbine flow meter 1.5" 24 x 52 x 84 585 265 M4430W A0300FM150WE with turbine flow meter 1.5" 39 x 69 x 96 710 322
Note: This information is not intended to replace the product installation and safety information available or the experience of a trained prod­uct installer. Please refer to the product installation and safety instructions for further information.
A Watts Water Technologies Company
ES-WQ-CWS150 1306 © 2013 Watts
USA: Tel. (800) 659-8400 • www.watts.com
Canada: Tel. (888) 208-8927 • www.watts.ca
Loading...