Series B6010,
B6011 and B6013
2-Piece, Standard Port,
Bronze Ball Valves
Sizes: 1⁄2" – 2" (15 – 50mm)
Series B6010, B6011 and B6013 2-Piece, Standard Port,
Bronze Ball Valves feature a blowout proof pressure retaining
stem. The B6010, B6011, B6013’s standard port orifice
ensures minimal pressure drop, while Durafill
®
and Uniseal
®
seats and chrome plated brass ball provide lasting service for a
wide range of liquids and gases.
Features
• Designed for quick and easy cleaning or replacement of
worn parts without dismantling pipe line
• Durafill
®
(carbon/glass filled PTFE) seats for size 1⁄2" and 11⁄4"
– 2" (15 and 32 – 50mm) and Uniseal
®
(enhanced PTFE)
seats for sizes
3
⁄4" & 1" (20 & 25mm) for lasting service for a
wide range of liquids and gases
• Chrome plated brass ball is wiped clean during each operation of the valve
• Minimal pressure drop due to large ports
• Blowout proof, pressure retaining stem
• Pressure rated at 600psi (41 bar) WOG non-shock for
threaded end; 400psi (28 bar) WOG non-shock for solder
end at 100°F (38°C)
• High cycle life reinforced PTFE stem packing seal and thrust
washer
• Vinyl insulator on heavy duty, zinc-plated, carbon steel handles
• Quarter-turn open or close operation
• Low operating torque
• Adjustable stem packing gland
• Each valve factory tested
Models
B60101⁄2" – 2" (15 – 50mm) threaded NPT end connections
B6011
1
⁄2" – 2" (15 – 50mm) solder end connections*
B6013
1
⁄2" – 1" (15-25mm) solder end x threaded end male
union*
For Commercial Applications
ES-B6010
Job Name
–––––––––––––––––––––––––––––––––––––––––––
Contractor
––––––––––––––––––––––––––––––––––––––––––––
Job Location
–––––––––––––––––––––––––––––––––––––––––
Approval
–––––––––––––––––––––––––––––––––––––––––––––
Engineer
–––––––––––––––––––––––––––––––––––––––––––––
Contractor’s P.O. No.
–––––––––––––––––––––––––––––––––––
Approval
–––––––––––––––––––––––––––––––––––––––––––––
Representative
––––––––––––––––––––––––––––––––––––––––
B6013
Specifications
A 2-piece standard port bronze ball valve to be installed as
indicated on the plans. The valve must have a blowout proof
pressure retaining stem, Durafill
®
seats (1⁄2" and 11⁄4" – 2") or
Uniseal
®
seats (3⁄4" & 1"), reinforced PTFE stem packing seal,
and chrome plated brass ball. Pressure rating no less than
600psi (41 bar) WOG non-shock for threaded end and 400psi
(28 bar) WOG non-shock for solder end. Valve shall be a
Watts Regulator Company Series B6010, B6011 or B6013.
Options
Suffix
SS – Stainless steel ball and stem
VT – Virgin PTFE seat material
Pressure – Temperature
Temperature Range: 0°F – 225°F (-18°C – 107°C)
Maximum Working Pressure: 600psi (41 bar) WOG non-shock
for threaded end and 400psi (28 bar) WOG non-shock for solder end @ 100°F (38°C). Not rated for steam service due to
union end gasket.
*This valve is designed to be soft soldered into lines without
disassembly, using a low temperature solder 420°F (215°C).
Other solders such as 95/5 tin antimony 460°F (238°C) can be
used. However, extreme caution must be used to prevent seat
damage. Higher temperature solders will damage the seat
material. ANSI B.15.18 states that the maximum operating
pressure of 50-50 solder connections is 200 psi (14 bar) at
100°F (38°C) and decreases with higher temperature.
Apply heat with the flame directed AWAY from the center of the
valve body. Excessive heat can harm the seats. After soldering,
the packing nut may have to be tightened.
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,
please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
B6011
B6010