Model 680003
Add-on Shower
Diverter Spout Type 0140492
IS-680003
Installation Instructions
1. Turn off water supply.
2. Remove existing spout by unscrewing it in he counter-clockwise
direction.
3. Install new diverter spout (1) onto threaded stub out.
4. Thread on pipe coupling (3) onto straight section of riser (2)
5. Thread on shower head (4) onto curved end of upper
looped riser (5).
6. Assemble support flange (6) to brass support ring (7) using flat
7. Slide up the brass support ring and flange assembly (7 & 6) onto
8. Thread in straight end of upper looped riser (5) into the pipe cou-
9. Thread in complete riser assembly into spout connector nut (9)
10. Move up brass support ring (7) with the support flange (6) to
11. Fasten support flange (6) to wall using the two wood screws
Note: When fastening flanges to drywall (plaster board) or hollow
12. The assembly of the add-on shower unit is now completed
13. Turn on water and check for leaks at all connections.
Note: Apply pipe dope or teflon tape to all threaded connections
1
head
/4 - 20 x 5/8" machine screw (8).
the straight end of the looped riser (5).
pling (3) to join the lower straight riser (2). Tighten connection.
located on top of spout (1). Tighten connector nut (9) making
sure that the shower head (4) is facing in the same direction as
the spout (1).
desired height.
supplied with the flange.
wall, use plastic anchors (not provided). Usually plastic anchors
require a 1/4" hole to be drilled into the wall before inserting
the anchors.
(not provided in this package).
11
6
8
6
7
3
2
9
Stub Out
1
Limited Warranty: Watts Regulator Co. (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of
original shipment. In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER WARRANTIES,
EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting from
labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no control.
This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above
limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to
determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
Brass & Tubular Products
Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca
IS-680003 0904 EDP# 1916048 © Watts, 2009
USA: 815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com