Waterloo F1971 User Manual [en, es]
OPERATOR’S MANUAL
SAFETY
FLOOR CABINET
SERVICE PARTS
IN THE UNITED STATES CALL 1-800-833-4405
FOR SERVICE PARTS. Outside the United States call your
local distributor. Please provide the Model Number when calling.
Locating Model # Information
Model numbers and other information required for service parts is
located on a white label on the upper right hand corner of the unit.
CAPACITIES
• The maximum weight for each shelf should be no more than
50 lbs. (evenly distributed).
• The maximum product weight including contents should be no
more than 300 lbs.
DANGER is used to indicate a hazardous
situation which, if not avoided, will result in serious injury
or death.
WARNING indicates a hazardous situation which,
if not avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation
which, if not avoided, may result in minor injury, moderate
injury, or property damage.
CAUTION: Read and follow all Safety Rules and
Operating Instructions before rst use of this product.
DANGER
• DO NOT stand on this product. You may fall which
may cause personal injury.
• DO NOT mount this product on a truck bed or any
other moving object. This may cause personal injury or
product damage.
• DO NOT step on the shelves. You may fall which may
cause personal injury.
WARNING
• Use appropriate safety equipment when using power
and hand tools. Failure to do so may cause personal
injury or product damage.
• Use adequate manpower when assembling and moving
this unit. Failure to do so may cause personal injury or
product damage.
• DO NOT alter this product in any manner. This may
cause product damage or personal injury.
• Keep the product on level surfaces. The product may
become unstable and tip if stored or moved on an
un-level surface, which may cause personal injury
or product damage.
• Cabinet MUST be attached to a stud in a wood frame
wall. Failure to do so may cause personal injury or
product damage.
• Hardware is provided for wood frame wall use only.
Concrete or other surfaces will require other hardware
(not provided). Use appropriate hardware per your local
building codes. Failure to do so may cause personal injury
or product damage.
CAUTION
MAINTENANCE
• Periodically the surfaces should be cleaned with a mild
detergent and water.
• Grease and oil can be removed with most standard cleaning
uids. For safety, use a nonammable cleaning uid.
• Auto wax will preserve the unit’s luster nish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.
Waterloo Industries, 139 West Forest Hill Avenue, Oak Creek, WI 53154
• Appropriately secure this product before moving it with
a forklift.
F1971
HARDWARE
CARTON CONTENTS
TOOLS REQUIRED:
Socket Wrench 3/8" Socket
7/16" Deep-well Socket 7/16" Open End Wrench
Square Flathead Screwdriver
Cross-tip Screwdriver Drill
1/8" Drill Bit 1/4" Drill Bit
HARDWARE INCLUDED:
1/4-20 x 5/8" Carriage Bolt (Qty: 14)
1/4-20 x 3/4" Button Head Screw (Qty: 24)
11/32" Washer (Qty: 14)
1/4-20 Serrated Flange Nut (Qty: 38)
#8 - 32 x 3/8" Pan Head Screw (Qty: 16)
A. Side Panel
B. Top
C. Back Panel
D. Shelf
E. Door Left
F. Door Right
G. Bottom
H. Wall Bracket
C (2)
B
A (2)
D(3)
5/32" Hex Key (Qty: 1)
Screw Leveler (Qty: 4)
#14 x 3 Hex Head Screw (Qty: 1)
Magnet (Qty: 2)
Snap Grommet (Qty: 2)
F
H
E
G
2
ASSEMBLY
Items Needed:
1/4-20 x 3/4" Button Head Screw (Qty: 3)
1/4-20 Serrated Flange Nut (Qty: 3)
Back (Qty: 2)
Process:
• Place (2) Backs with anges up as shown.
(Use packaging material to prevent scratches.)
• Assemble (2) Backs, using (3) 1/4-20 x 3/4" Button Head
Screws, and (3) 1/4-20 Serrated Flange Nuts through
anges.
• Finger tighten.
Nut
Screw
Items Needed:
1/4-20 x 3/4" Button Head Screw (Qty: 4)
1/4-20 Serrated Flange Nut (Qty: 4)
Side (Qty: 2)
Process:
• Attach (2) Side Panels using (2) 1/4-20 x 3/4" Button
Head Screws, and (2) 1/4-20 Serrated Flange Nuts
nuts in middle holes of each side. Leave end
holes open for later assembly.
• Finger tighten.
Back Panel
Side Panel
Nut
Screw
Figure 1
Figure 1.1
Screw
Back Panel
Figure 2
Side Panels
Nuts
Nut
Back Panels
Screws
3
Items Needed:
1/4-20 x 5/8" Carriage Bolt (Qty: 4)
1/4-20 x 3/4" Button Head Screw (Qty: 8)
11/32" Washer (Qty: 4)
1/4-20 Serrated Flange Nut (Qty: 12)
Top (Qty: 1)
Process:
• Insert Top into one end of assembly and attach
using (4) 1/4-20 x 5/8" Carriage Bolt , (8) 1/4-20 x 3/4"
Button Head Screws, (4) 11/32" Washer and (8) 1/4-20
Serrated Flange Nuts.
• Finger tighten.
Top
Items Needed:
1/4-20 x 5/8" Carriage Bolt (Qty: 6)
Shelf (Qty: 3)
11/32" Washer (Qty: 6)
1/4-20 Serrated Flange Nut (Qty: 6)
Process:
Note: Install top shelf rst.
• Place the cabinet in its upright position.
• Insert Shelf from bottom of unit.
• Place in desired mounting location in back of unit, and
rotate into place as shown.
• Attach using (2) 1/4-20 x 5/8" Carriage Bolts, (2)
11/32" Washers, and (2) 1/4-20 Serrated Flange Nuts
in square mounting holes as shown.
• Repeat until all 3 shelves are in place.
• Finger tighten.
Carriage
Bolt
Washer
Nut
Figure 3
Figure 3.1
Nut
Button Head Screw
Washer
Nut
Flanges
toward bottom
Figure 4
Carriage
Bolt
Note: Shelves may be organized in several different
congurations. Below is the recommended initial shelf
spacing. Top and bottom shelf spacing may be adjusted as
necessary.
Top Bottom
Top middle
mounting position
Figure 4.1
4
Items Needed:
1/4-20 x 5/8" Carriage Bolt (Qty: 4)
1/4-20 x 3/4" Button Head Screw (Qty: 8)
11/32" Washer (Qty: 4)
1/4-20 Serrated Flange Nut (Qty: 12)
Bottom (Qty: 1)
Process:
• Insert Bottom into lower end of assembly and attach
using (4) 1/4-20 x 5/8" Carriage Bolt , (8) 1/4-20 x 3/4"
Button Head Screws, (4) 11/32" Washer and (8) 1/4-20
Serrated Flange Nuts.
• Finger tighten.
Items Needed:
Screw Leveler (Qty: 4)
Magnet (Qty: 2)
Snap Grommet (Qty: 2)
Process:
• Install (4) Screw Levelers. Some adjustments may
be necessary after cabinet is in desired location.
Figure 6
Figure 5
Nut
Washer
Bottom
• Place the cabinet in its upright position.
• Square the cabinet and wrench tighten all bolts.
Square
Figure 6.1
Carriage
Bolt
Figure 5.1
Button Head Screw
Nut
5
Loading...