Waterloo F1881 User Manual [en, de, es, fr]

OPERATOR’S MANUAL

3-DRAWER UTILITY CART

SERVICE PARTS

In the United States Call 1-800-833-4405 for Service Parts.

Outside the United States call your local distributor. Please pro­vide the Model Number when calling.

LOCATING MODEL # INFORMATION
Model number and other information required for service parts
is on a label included separately in the packing at the top of the
carton or located on the back of the unit. If included separately,
afx label to the back of the unit for future reference.

CAPACITIES

• The maximum weight for each drawer should be no more than
25 lbs.

• The maximum product weight, including contents, should be no
more than 400 lbs.

MAINTENANCE

• For casters, use high quality bearing grease (yearly).

• Lubricate the slides with grease or equivalent (twice yearly.)

Ball bearing slides

• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit’s luster nish. Apply the wax as to
a car. The wax will also help protect the unit against scratches.

• Grease and oil can be removed with most standard cleaning
uids. For safety, use a nonammable cleaning uid.

• If drawer liners are supplied, it is recommended they are used
to protect the nish inside the drawers and to make the drawers
easier to clean. The drawer liners may be cleaned with soap and
water.

Friction slides

SAFETY

DANGER is used to indicate a hazardous situation which,
if not avoided, will result in serious injury or death.
WARNING indicates a hazardous situation which, if not
avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation which, if not
avoided, may result in minor injury, moderate injury, or property
damage.

CAUTION: Read and follow all Safety Rules and Operating In­structions before rst use of this product.

DANGER

• DO NOT stand on this product. You may fall or cause product to
tip.

• DO NOT open more than one drawer at a time. The product may
become unstable and tip.

• DO NOT step in the drawers. You may fall or cause product to
tip.

• DO NOT mount this product on a truck bed or any other moving
object.

• DO NOT move the product prior to closing and locking all the
drawers. The drawers could come open and make the product
unstable and tip.

WARNING

• WEAR SAFETY GLASSES when removing or repositioning the
slides.

• DO NOT pull this product when moving it. Push the product to

prevent personal injury.

• USE THE BRAKES when not moving this product. This will pre­vent the product from rolling.

• DO NOT alter this product in any manner. For example, do not
weld external lockbars or attach electrical equipment.

• Keep the product on level surfaces. The product may become
unstable and tip if stored or moved on an uneven surface.

• BE CAREFUL when closing the cover. Remove hands before the
cover closes completely.

• Lubricate lock with graphite (yearly).

Waterloo Industries, 139 West Forest Hill Avenue, Oak Creek, WI 53154, USA

CAUTION

• This product is not designed to be directly lifted with a fork lift, or
to be towed with any mechanical devices.

• The maximum weight for each drawer should never be exceed­ed.

• Only transport this product empty. Properly secure when trans­porting.

• DO NOT exceed maximum product weight, including contents.
See Capacities section for load rating.

F1881

HARDWARE

5/16-18 x 5/8" Carriage Bolt (Qty: 38)

WASHER .312 X .750

5/16-18 Hex Lock Nut (Qty: 56)

5/16 x 5/8" Hex Head Screw (Qty: 16)

5/16-18 x 5/8" Carriage Bolt (Qty: 2)
(In Seperate Bag)

CARTON CONTENTSHARDWARE

TOOLS REQUIRED:

Screwdriver, athead
7/16” Wrench
3/8” Wrench
Rubber Mallet

HARDWARE REQUIRED:

M8-1.25 x 16mm Carriage Bolt
(Qty: 38)

M8 Washer (Qty: 56 )

M8-1.25 Hex Lock Nut (Qty: 60)

A. Locking Top and Drawer Unit
B. Handle
C. Leg
D. Left Rear Bumper
E. Left Front Bumper
F. Bottom Tray
G. Rigid Casters
H. Swivel Casters
J. Support Rail
K. Side Support Rail
L. Gas Spring
M. Right Front Bumper
N. Right Rear Bumper

A

B

L(2)

N

M

M8-1.25 x 16mm Hex Head
Screw (Qty: 16)

M8-1.25 x 16mm Carriage Bolt
(Qty: 2) (In a Seperate Bag)

D

with
notch

C(4)

E

with
notch

K(2)

J(2)

G(2)

F

H(2)

2

ASSEMBLY

LEFT LEG ASSEMBLY
Items Needed:

Leg (Qty: 2)
Left Rear Bumper (Qty: 1)
Left Front Bumper (Qty: 1)
Bottom Tray (Qty: 1)
M8-1.25 x 16mm Carriage Bolt (Qty: 8)
M8 Washer (Qty: 8)
M8-1.25 Hex Lock Nut (Qty: 8)

Process:
NOTE: Remove all components from drawers before

assembling this unit. Make sure the arrows on the legs are
pointing upwards. Failure to follow this will cause the legs
to be misaligned.

• Assemble Bottom Tray, Left Rear Bumper, Left Front
Bumper, and (2) Leg, as shown, using (4) M8-1.25 x
16mm Carriage Bolt, (4) M8 Washer, and (4) M8-1.25
Hex Lock Nut in each Leg.

• Finger tighten.

RIGHT LEG ASSEMBLY
Items Needed:

Right Front Bumper (Qty: 1)
Right Rear Bumper (Qty: 1)
Leg (Qty: 2)
Bottom Tray Assembly (from Step 1)
M8-1.25 x 16mm Carriage Bolt (Qty: 8)
M8 Washer (Qty: 8)
M8-1.25 Hex Lock Nut (Qty: 8)

Process:

• Attach Right Front Bumper, Right Rear Bumper, and
remaining Leg to opposite end of Bottom Tray in the
same manner from Step 1.

• Finger tighten.

Right Rear
Bumper (N)

Leg (2)

Right Front
Bumper (M)

Left Rear
Bumper (D)

Align
holes

Leg

Bottom Tray

Left Front
Bumper (E)

SUPPORT RAIL INSTALLATION
Items Needed:

Support Rail (Qty: 2)
M8-1.25 x 16mm Carriage Bolt (Qty: 4)
M8 Washer (Qty: 4)
M8-1.25 Hex Lock Nut (Qty: 4)

Process:

• Attach (2) Support Rail, as shown, using (4) M8-1.25 x
16mm Carriage Bolt, (4) M8 Washer, and (4) M8-1.25
Hex Lock Nut in each Support Rail.

• Finger tighten.

Flanges
inside

Support
Rail

3

SIDE SUPPORT INSTALLATION

Items Needed:

Side Support Rail (Qty: 2)
M8-1.25 x 16mm Carriage Bolt (Qty: 4)
M8 Washer (Qty: 4)
M8-1.25 Hex Lock Nut (Qty: 4)

Process:

• Attach (2) Side Support Rail, as shown, using (2) M8-

1.25 x 16mm Carriage Bolt, (2) M8 Washer, and (2)
M8-1.25 Hex Lock Nut in each Side Support Rail.

• Finger tighten.

Flange

Side Support Rail

on top

• Attach assembly from steps 1 through 4, using (12) M8-

1.25 x 16mm Carriage Bolt, (12) M8 Washer, and (12)
M8-1.25 Hex Lock Nut.

• The notches should be on the side with the label. Leave
holes in notches open for later assembly.

• Finger tighten.

Nut

TOP AND DRAWER UNIT ASSEMBLY

Items Needed:

Locking Top and Drawer Unit (Qty: 1)
M8-1.25 x 16mm Carriage Bolt (Qty: 12)
M8 Washer (Qty: 12)
M8-1.25 Hex Lock Nut (Qty: 12)

Process:

• Place Locking Top and Drawer Unit on its back on
packaging material as shown.

Bolt

Leave open for

Label

later assembly

Notch

HANDLE INSTALLATION
Items Needed:

Handle (Qty: 1)
M8-1.25 x 16mm Carriage Bolt (Qty: 2)
M8 Washer (Qty: 4)
M8-1.25 Hex Lock Nut (Qty: 4)
M8-1.25 x 16mm Carriage Bolt (Qty: 2) (In Separate Bag)

Process:

• Attach Handle to bottom set of holes using (2) M8-1.25
x 16mm Carriage Bolt, (2) M8 Washer, and (2) M8-1.25
Hex Lock Nut.

• Install (2) M8-1.25 x 16mm Carriage Bolt (In a Separate
Bag) in top set of holes using (2) M8 Washer and (2) /16­18 Hex Lock Nut.

• Finger tighten.

Carriage Bolts

Packaging

material

Carriage Bolts
(In a separate bag)

Hinge

Packaging

material

4

GAS SPRING INSTALLATION
Items Needed:

Gas Spring (Qty: 2)
M8-1.25 Hex Lock Nut (Qty: 4)
12mm Wrench
13mm Wrench

Process:
NOTE: Gas Spring must be installed with the cartridge

attached to lid (as shown).

• Insert threaded rod through hole in lid and secure with
locking nut.

• Insert bottom of Gas Spring in hole in divider rail and
secure with locking nut.

• Repeat for opposite side.

• Wrench tighten all fasteners on unit.

LOGO LABEL PLACEMENT

Process:

• Peel backing from logo label and position the label in
the upper right corner of the cart, using the dimensions
shown as a guide.

3.00

1.90

OPERATION

REMOVING DRAWERS

• Empty the drawer.

• Fully extend the drawer

Release

Gas Spring

CASTER INSTALLATION

Items Needed:

Rigid Casters (Qty: 2)
Swivel Casters (Qty: 2)
M8-1.25 x 16mm Hex Head Screw (Qty: 16)
M8 Washer (Qty: 16)
M8-1.25 Hex Lock Nut (Qty: 16)
13mm Wrench
14mm Wrench

Process:
NOTE: Mount both Swivel Casters on the same side of the

unit as the handle.

• Attach Rigid Casters and Swivel Casters using (4) M8-

1.25 x 16mm Hex Head Screw, (4) M8 Washer, and (4)
M8-1.25 Hex Lock Nut in each caster.

• Wrench tighten.

• Discard screws in caster package (if supplied).

Nut

Lever Style - Lift or lower (depending on the slide) the
release lever on both sides, (this allows the slides to ride
over the stops.) Pull out to remove.

Tab Style - Depress the release tabs on both sides,
(this allows the slides to ride over the stops.) Pull out to
remove.

5

OPERATION

REINSTALL DRAWERS
Ball bearing slide - Pull slides and slide carrier out to fully

extended position (see illustration.) Hold the slide on the
cabinet while aligning it with the slide on drawer. Slightly
insert one side and repeat for the other side. Slowly push
drawer to its fully closed position to engage slide. Open
drawer and reclose to ensure proper operation.

slide carrier

slide

MODIFYING DRAWER LOCK
▪ To open, lift up on the drawer front while pulling

towards you.

Striker

▪ To close, shut the drawer rmly until the latch engages.
▪ Pull back lightly to see if the drawer is completely closed.
▪ If the drawer does not stay closed, the striker may be

bent, or the striker rubs against the drawer slides.

▪ To x the problem, lightly bend the striker until the drawer

will engage in the slide.

6

MANUAL DE USUARIO

CARRITO MULTIUSO DE 3 CAJONES

Cojinetes de bolas

• Limpie con detergente suave y agua los frontales y los bordes laterales
de los cajones y las demás supercies.

• La cera para automóviles preservará el acabado brilloso de la unidad.
Aplique la cera como lo haría al carro. La cera también ayudará a prote­ger la unidad contra raspones.

• La grasa y el aceite pueden retirarse con la mayoría de los líquidos
estándar para limpieza. Por razones de seguridad, utilice un líquido
incombustible para limpieza.

• Si se suministran forros para las gavetas, se recomienda que se utilicen
para proteger el acabado interno de las mismas y para facilitar la limp­ieza. Los forros para gavetas pueden limpiarse con agua y jabón.

Correderas de friccion

SEGURIDAD

PELIGRO se utiliza para indicar una situación peligrosa que, de

no evitarse, resultará en lesiones graves o la muerte.

ADVERTENCIA indica una situación peligrosa que, de no

evitarse, podría producir lesiones graves o la muerte.

PRECAUCIÓN se utiliza para indicar una situación peligrosa que, de

no evitarse, puede derivar en lesiones leves o moderadas, o en daño a la
propiedad.

ATENCIÓN: Lea y siga todas las Normas de Seguridad y las Instruccio-

nes de Funcionamiento antes de utilizar por primera vez este producto.

PIEZAS DE SERVICIO

EN ESTADOS UNIDOS LLAME al 1-800-833-4405 para piezas de

repuesto. Fuera de Estados Unidos llame a su distribuidor local. Prière
de fournir le numéro de modèle au moment de l’appel.

CÓMO UBICAR LA INFORMACIÓN DEL NÚMERO DE MODELO
El número de modelo y otra información requerida para obtener piezas de
repuesto, están en una etiqueta incluida separadamente en el empaque
en la parte superior de la caja o ubicada en la parte posterior de la unidad.
Si se incluye separadamente, ja la etiqueta a la parte posterior de la
unidad para consultas futuras.

CAPACIDAD

• El peso máximo en cada gaveta no debe ser mayor de 11,4 kg.

• El peso máximo del producto, incluyendo su contenido, no debe ser
mayor de 181,8 kg.

MANTENIMIENTO

• Para las ruedas, utilice grasa para rodamientos de alta calidad (anual­mente).

• Lubrique las guías con grasa o equivalente (dos veces por año).

• Lubrique la cerradura con grato (anualmente).

PELIGRO

• NO se ponga de pie sobre esta unidad. Puede caerse u ocasionar que

el producto se vuelque.

• NO abrir más de un cajón a la vez. El producto podría quedar inestable

y volcarse.

• NO utilice las gavetas como peldaños. Puede caerse u ocasionar que

el producto se vuelque.

• NO monte este producto en una cama de carro o ninguÌn otro objeto

móvil.

• NO mueva la unidad antes de cerrar y asegurar todas las gavetas. Las

gavetas podrían abrirse y hacer que la unidad se vuelva inestable y se
vuelque.

ADVERTENCIA

• USE GAFAS DE SEGURIDAD al quitar o volver a poner las correderas.

• NO hale la unidad, empújela cuando la mueva.

• UTILICE LOS FRENOS cuando el producto no esté en movimiento. Esto

impedirá que se deslice.

• NO altere la unidad en modo alguno. Por ejemplo, no suelde las barras
de sujeción externas ni le incorpore equipos eléctricos.

• Mantenga la unidad en supercies niveladas. La unidad puede tornarse
inestable y volcarse si se almacena o se moviliza en una supercie no
nivelada.

• TENGA cuidado cuando cierre la tapa. Quite las manos antes de que la
tapa cierre completamente.

PRECAUCIÓN

• Este producto no está diseñado para ser levantado directamente con un
montacargas, ni para ser remolcado con unidades mecanizadas.

• Nunca debe exceder el peso máximo de cada gaveta.

• Sólo transporte esta unidad cuando esté vacía. Asegúrela adecuada­mente cuando la transporte.

• NO exceda el peso máximo del producto, incluyendo el contenido. Ver la
Sección de Capacidades para capacidad de carga.

Waterloo Industries, 139 West Forest Hill Avenue, Oak Creek, WI 53154, USA

F1881

HARDWARE

5/16-18 x 5/8" Carriage Bolt (Qty: 38)

WASHER .312 X .750

5/16-18 Hex Lock Nut (Qty: 56)

5/16 x 5/8" Hex Head Screw (Qty: 16)

5/16-18 x 5/8" Carriage Bolt (Qty: 2)
(In Seperate Bag)

CONTENIDO DE LA CAJA DE CARTÓNFERRETERÍA

HERRAMIENTAS NECASARIAS:

Destornillador de cabeza plana
Destornillador, punta de cruz
Llave Inglesa de 7/16”
Llave inglesa de 3/8”
Mazo de goma

ACCESORIOS NECESARIOS:

Perno de Carro M8-1,25 x 16mm
(Cant.: 38)

Arandela de M8 (Cant.: 56 )

Tuerca Hexagonal de Seguridad
M8-1,25 (Cant.: 16)

A. Cubierta de Seguridad y Unidad de Cajón
B. Manija
C. Pata
D. Protector Posterior Izquierdo
E. Protector Delantero Izquierdo
F. Bandeja Inferior
G. Ruedas rígidas
H. Ruedas giratorias
J. Baranda de Apoyo
K. Baranda Lateral de Apoyo
L. Émbolo
M. Protector Delantero Derecho
N. Protector Posterior Derecho

A

B

C(4)

L(2)

N

M

K(2)

Tornillo de Cabeza Hexagonal M8

-1,25 x 16mm (Cant.: 16)

Perno de Carro M8-1,25 x 16mm
(Cant.: 2) (En una bolsa separada.)

J(2)

D Con

muesca

G(2)

E

Con
muesca

F

H(2)

2