Waterloo F1526A2 User Manual [en, de, es, fr]
OPERATOR’S MANUAL
BACKWALL WITH METAL PEGBOARD
CAUTION: Backwall MUST be attached to the Workbench before the
top is attached and the drawers are installed.
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
F1526A2
SAFETY
SAFETY WARNINGS AND CAUTIONS:
• Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or product damage.
• Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or product damage.
• DO NOT stand on this product. You may fall which may cause personal injury.
• DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage.
• Appropriately secure this product before moving it with a forklift.
• DO NOT tow with power equipment. The product could tip, which may cause personal injury or product damage.
• DO NOT alter this product in any manner. This may cause product damage or personal injury.
• Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an un-level surface, which may
cause personal injury or product damage.
• Be sure the workbench is flat on the floor before installing the Workbench Backwall. Failure to do so may cause personal injury or product
damage.
• The maximum weight allowed to hang on or be in any way supported from the backwall is 65 pounds. If the limit is exceeded the product
may tip and cause personal injury or product damage.
• Be sure to secure the unit to a studded or concrete wall. Failure to do so may cause the unit to become unstable and tip. This may cause
personal injury or product damage.
• Use only the provided pegboard on Workbench Backwall.
• Backwall with Metal Pegboard is only to be attached to one of the following Workbenches: WB5002, WB5003, WB5507. Failure to do so
could result in personal injury or product damage.
Socket Wrench
7/16" Socket
3/8" Wrench
Drill
1/8" Drill Bit
Screwdriver, Crosstip
Screwdriver, Flathead
Hardware Included:Tools Required:
AA(14)
EE(16)
BB(2)
FF(16)
CC(3)
DD(2)
GG(4)
In the United States Call 1-800-833-4405 for Service Parts. Outside the United States call your local distributor.
2
3
WARNING: Backwall with Metal Pegboard is only to be attached to
one of the following Workbenches: WB5002, WB5003, WB5507.
NOTE: To assemble the Backwall, the drawers and top must first be
removed from the workbench.
REMOVING AND INSTALLING DRAWERS:
FRICTION SLIDES
• Empty the drawer.
• Fully extend the drawer. Push it back a quarter of an inch, (6
mm).
• Insert a screwdriver into the slot in the slide and push in on the
stop until it clears the lance.
Slot
Stop
Lance
Lubricate
• Repeat the procedure on the other slide and remove the drawer.
• To reinstall the drawer, pry the stop far enough out to engage the
lance and push the drawer onto the slides until the stops pass
over the lances.
ASSEMBLY
STEP 1:
BB(2)
EE(2)
FF(2)
• Remove and reuse the top fasteners from the top back of
the workbench.
• Attach (2) A to workbench, as shown, using existing
hardware and (2) BB, (2) EE and (2) FF.
• Finger tighten.
Existing Hardware
Flange
pointed back
BALL BEARING SLIDES
• Empty the drawer.
• Fully extend the drawer.
Lever Style - Lift or lower (depending on the
slide) the release lever on both sides, (this
allows the slides to ride over the stops.) Pull
out to remove.
Tab Style - Depress the release tabs on
both sides, (this allows the slides to ride over
the stops.) Pull out to remove.
• To reinstall, carefully align
the slides and slowly push
the drawer into the unit until
the drawer stops.
A
FF
EE
Release
BB
TOP REMOVAL:
• Remove and reuse fasteners from wood top.
• Remove top from workbench base.
4
STEP 2:
STEP 3:
CC(1)
AA(8) EE(8) FF(8)
Note: Option 1 shows mounting the backwall to a workbench
with a 54 inch top. To mount the backwall to a workbench with
a top that is larger than 54 inches wide, go to option 2.
OPTION 1:
• Attach (2) C and (2) B to (2) A, as shown, using (8) AA, (8)
EE and (8) FF.
• Finger tighten.
FF
EE
C
Flanges pointed
forward
A
B
AA
• Install (1) CC in flanges of (2) B.
CC
Back of workbench
Flanges
with holes
together
OPTION 2:
• Attach (2) C and (2) B to (2) A, as shown, using (8) AA, (8)
EE and (8) FF.
• Finger tighten.
A
FF
EE
B
C
Flanges pointed
back
AA
• Wrench tighten fasteners from step 1.
Fasteners from
step 1
Flanges
with holes
together
5
STEP 4:
AA(2)
CC(2)
STEP 5:
AA(4) EE(4) FF(4)
EE(2)
FF(2)
Assemble tray.
• Attach E to right end of D, using (1) AA, (1) CC, (1) EE and
(1) FF.
• Do not tighten.
FF
EE
AA
E
CC
• Install tray as shown, using (4) AA, (4) EE and (4) FF.
• Finger tighten.
AA
EE
FF
Front
Back
STEP 6:
D
Flange pointed
down
• Attach F to the other end of D in the same manner.
FF
EE
AA
F
CC
D
Flange pointed
down
NOTE: To reattach the top, new pilot holes will need to be
marked and drilled.
• Place top on the bench in the desired location.
• Mark centers of mounting holes to be drilled.
• Drill 1/8" pilot holes in top.
• Reattach top using existing hardware.
• Wrench tighten all fasteners.
• Reinstall drawers.
Back
Front
Reattach top
using existing
hardware.
6
STEP 6 - Continued:
(For workbenches with 54" top only.)
DD(2)
• Drill (2) 1/8" pilot holes in top using holes in C(2) as a
template.
• Attach using (2) DD.
Back
Front
MAINTENANCE
C Periodically the surfaces should be cleaned with a mild
detergent and water.
C Auto wax will preserve the unit's luster finish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.
C Grease and oil can be removed with most standard cleaning
fluids. For safety, use a nonflammable cleaning fluid.
7
MANUAL DE USUARIO
MONTAJE EN PARED CON TABLERO METÁLICO
PRECAUCIÓN: La parte posterior DEBE fijarse al banco de trabajo
antes de unir la parte superior y de que se instalen las gavetas.
ATENCIÓN: Lea y siga todas las Normas de Seguridad y las Instrucciones de Funcionamiento antes
de utilizar por primera vez este producto.
F1526A2
SEGURIDAD
ADVERTENCIAS Y PRECAUCIONES DE SEGURIDAD:
• Utilice el equipo de seguridad adecuado cuando emplee herramientas eléctricas. De lo contrario, podría causarle lesiones personales u ocasionar daños
al producto.
• Utilice el personal adecuado para el montaje y el traslado de esta unidad. De lo contrario podría ocasionarse lesiones personales o dañar el producto.
• NO se ponga de pie sobre la unidad. Podría caerse y lesionarse.
• NO monte esta unidad en la plataforma de carga de la camioneta ni en ningún otro objeto móvil. Podría causar lesiones personales o daño a la unidad.
• Asegure adecuadamente la unidad antes de moverla con un montacargas.
• NO arrastre la unidad con equipo eléctrico. La unidad podría volcarse, lo cual podría ocasional lesiones personales o daño a la unidad.
• NO altere este producto de modo alguno. Esto podría dañar el producto o causarle lesiones personales.
• Mantenga el producto sobre superficies planas. El producto puede desestabilizarse y volcar si se almacena o se mueve en superficies no llanas, lo cual
podría causar lesiones personales o dañar el producto.
• Cerciórese de que el banco de trabajo esté plano en el piso antes de instalar la parte posterior del banco de trabajo. De lo contrario podría ocasionar
lesiones personales o daño al producto.
• El peso máximo permitido para colgar o que puede soportar la unidad de pared es de 65 libras (29,50 kg). Si se excede el límite, la unidad puede volcar y
causar lesiones personales o daños al producto.
• Asegúrese de afianzar la parte posterior del banco de trabajo a una pared de cemento o tachonada. De lo contrario la unidad podría desestabilizarse y
caer. Esto podría causarle lesiones personales o dañar el producto.
• Utilice exclusivamente el tablero que se suministra con el Panel Posterior de Pared.
• El tablero metálico trasero sólo se puede colocar en los siguientes modelos de bancos: WB5002, WB5003, WB5507. De lo contrario podría ocasionarse
lesiones personales o dañar el producto.
Herramientas Necasarias:
Llave de tubo
Casquillo adaptador de 7/16 pulgadas
Llave Inglesa de 3/8”
Talladro
Broca de 1/8 de pulgada
Destornillador, punta de cruz
Destornillador de cabeza plana
Ferretería Incluida:
AA(14)
EE(16)
BB(2)
FF(16)
CC(3)
DD(2)
GG(4)
En estados Unidos llame al 1-800-833-4405 para piezas de repuesto. Fuera de Estados Unidos llame a su distribuidor
local.
2
Loading...