WATERGUARD Solo User Manual
Water Leak Detection Equipment
Waterguard Solo
User Guide V19
© 2019 Waterguard Services Limited, All Rights Reserved
Waterguard Services Limited. Registered address: 22 Oakwell Business Centre, Oakwell View, Barnsley, South
Yorkshire, S71 1HX. Tel: 01226 244200. Email: enquiries@waterguard.co.uk.
Contact Us….
If you require any further assistance operating the Waterguard Solo or if the Solo is not functioning
correctly, please call our friendly customer service team on 01226 244200.
Home Maintenance….
The valve doesn’t open or close…………………….
If all controls are functioning as normal but the valve is failing to close, please see Routine
Maintenance below as the valve assembly may be blocked up.
How to manually bypass the valve to allow water flow…………………….
WARNING The manual bypass must only be used in an emergency to restore the water
supply when the controller is damaged or there has been a long term loss of mains power.
Rotate the whole coil head as shown.
NOTICE: THIS WILL DEACTIVATE WATER LEAK PREVENTION AND MAY
INVALIDATE YOUR BUILDINGS INSURANCE.
General Maintenance….
Automatic Testing – The valve driver is programmed to automatically close and open the valve
every 24 hours. This tests both the valve assembly and controls.
Routine Maintenance – This system requires minimal maintenance and will only require the
following:
• In hard water areas it is recommended that the valve assembly is dismantled and cleaned
with limescale remover every 12 months as build up can cause the unit to fail.
• After continued power loss the valve driver back up battery may need replacing. It is
recommended that a suitably qualified engineer changes the battery (3V lithium, size code
CR123A) after firstly turning off mains power to the unit.
VALVE
NORMAL
VALVE ON
BYPASS
To familiarise yourself with your installed Waterguard System please read this user guide in full. If you
have any further questions, please contact the office.
Understanding the Controls….
LED Indicator
Meaning
Solid red
Unit operating normally
Off, followed by brief
flashes
Device running on battery backup. Please see, the Home
Maintenance section
Equal intermittent flashes
A leak has been detected and the valve driver has closed the
valve. Please see, the Operating the Controls section.
Solid red followed by brief
flashes
The valve driver has closed the valve as the battery backup
requires replacing. Please see, the General Maintenance
section. In order to reinstate the water supply, bypass the
valve manually. Please see, the Home Maintenance section.
Operating the Controls….
Button Press
Command
Single short press when
valve is closed
This will open the valve and reset the guard time, confirmed by
a singular flash.
Single short press when
valve is open
This closes the valve, confirmed by equal intermittent flashes.
This can be used when leaving the property to shut off the
water supply and pressing again when your return to reinstate
the water.
NB. Please allow 10 seconds for the valve driver to operate.
System Profile….
This system protects properties by monitoring water usage from the incoming water mains
using a flow sensor that allows continuous water flow for a limited time before the controller
suspects a leak and automatically shuts off the water with a solenoid valve.
The Waterguard Solo has one level of guard (maximum time of continuous flow) which is
usually set by the installer, landlord or concierge with the controls often located in riser
cupboards or basements.
Power Loss….
In the event of any mains power loss the Solo has an integrated back up battery that will
power the controller for several weeks. If power is completely lost, please see General
Maintenance. No setup is required but it is advised to test the Solo once power is restored.
Test….
To check the operation of the Solo firstly change the maximum continuous flow allowance to
10 minutes using the setup instructions. Run the water in the property and if the water
supply is cut off after 10 minutes the installation of the Solo is complete. Ensure to change
the settings back to the preferred time once testing is complete.
If connected to a Waterguard DataCom, an SMS stating “LEAK Detected” will also be sent
to all registered personnel.
Technical Support….
If you discover that the Solo has shut off your water supply, please in the first instance
check for leaks around the property and contact your landlord, concierge or facilities
manager where applicable.
Technical support is available for controls only on 01226 397895 during office hours. Please
contact a local plumber and/or electrician for any issues with your valve assembly.
Solo Button –
Operates
system functions
Solo LED -
Indicates status of
system
Setup….
All Waterguard Solo controls are pre-set to allow a maximum of 30 minutes continuous
water flow, unless an alternative time is requested at time of purchase. In order to change
this default setting, follow the instructions below:
Press and hold the valve driver button for 25 seconds, the valve driver is now in set up
mode. Ensure you do not release the button after the initially 25 seconds and the valve
driver will flash as below in 5 second intervals.
• 1 flash = 10 minutes
• 2 flashes = 20 minutes
• 3 flashes = 30 minutes
• 4 flashes = 40 minutes
Release the valve driver button once the LED indicator has shown the required number of
flashes for the time limited required. Set up complete.
Loading...