Watec WAT-2400S, WAT-933 Operation Manual

Watec cameras are designed to be used safely. If not used safely, it may lead to a physical accident caused by fire and

electric shock. Therefore, please keep and read the “Cautions for safety” (P.2) for protection against accidents.

To Use This Product Safely

Guide to the Safety Symbols

Power Supply

Thank you for purchasing the “1/2.8” Compact High Sensitivity Camera

WAT-2400S / WAT-933

” (reffered to as the “product”

or “camera” in this manual). This operation manual covers safety, functions, installation and the correct operating procedure

for the camera. First, we ask you to read this operation manual thoroughly, then install and operate the product as advised.

For future reference, we also advise safekeeping of this manual. Not understanding the contents of the operation manual may

cause damage to the camera, personal belongings and/or result in injury. Watec is not responsible for any inconvenience or

the attendant damages to the video and monitoring recording equipment caused by misuse, miss-operation or improper wiring

of our equipment. If you do not understand the installation, operation or safety instructions expressed in this manual, please

contact the distributor or dealer from where the camera was purchased.

1/2.8” Compact High Sensitivity Network Camera

WAT-2400S (Color) WAT-933 (B&W)

Operation Manual

Power for the camera can either supplied by the PoE (Power over Ethernet) or DC power supply.

・PoE (Power over Ethernet)

Use the PoE hub or NVR supporting IEEE802.3af for the PoE power supply.

・

DC power supply

Use a stabilized power adaptor designed for DC+12-36V with a current capacity of more than 500mA.

Wiring of the connector must be exact (see

“Description of Parts” (P.4) “⑨4P Cable”

).

Utilize the option

SWI12-12-N-P5 (Power supply adaptor), CB-06 and/or CB-07

(Cable with connectors).

Failure to observe the precautions above may result in damage t

o the camera, power adaptor and fire.

“Danger” indicates a compulsorily prohibition to prevent accidents.

“Warning” may lead to a serious accident such as death or injury caused by fire or electric shock.

“Caution” may incur injury and cause damage to peripheral objects in the immediate surroundings.

“Notice” indicates instructions which must be completed.

Do not use the PoE and DC power supply at the same time!

/

|1/6|

Please read and understand the “Cautions for safety” below to ensure the correct use of the product.

Cautions for Safety

・Do not disassemble and/or modify the camera.

・Do not operate the camera with wet hands.

・Use the camera within the range of the power supply voltage specifications

The recommended voltage is DC+12 - 36V (DC+12V recommended). Also, we advise the use of

an “inline fuse” power line to protect the camera and peripheral equipment, where applicable.

・Do not expose the camera to wetness or high moisture conditions.

The camera is designed and approved for indoor use only.

The camera is not water-resistant or waterproof.

・Protect the camera from condensation.

Keep the camera dry at all times during storage and operation.

・Should the camera not work properly, unplug the power immediately.

Check the camera according to the “Problems and Trouble Shooting” (P.6) section.

・Avoid the striking of hard objects or dropping the camera.

The camera use high quality electrical parts and precision components and may inadvertently be

damaged if not cared for properly.

・Do not install the camera in a position subject to direct sunlight.

Sunlight shinning directly onto the camera lens can cause damage to the sensor.

・Select a stable place for installation of the camera.

Use an appropriately rated mount durable and strong for all installation position.

・Do not move the camera with the cables connected.

Before moving the camera, always remove any cables from the rear of the camera first.

・Avoid using the camera near any strong electro-magnetic field.

In the event of exposure to electromagnetic waves (causing the monitored image to become distorted)

we recommend the camera be shielded by an appropriate protective casing.

・Since the camera may become hot during operation, please provide a sufficient space around the camera

for heat dissipation. When you remove the camera, please let time pass for heat dissipation as well.

・Unplug the camera when unused for long periods of time.

・ Turn off the power of the camera before inserting or removing the microSD/SDHC/SDXC.

・Use an image that you have recorded on the product without authorization, there is a case where the conduct of the

disclosure, etc. it becomes infringement of copyright and portrait rights.

・In the video and sound to be taken using the camera, which can identify the individual will be personal information. Publishing

the video and sound will be necessary to obtain a pre-approval, it will be the responsibility of those who operate the system.

・Because the use at the place of high temperature and humidity adversely affects an internal parts, and life shortens by

deterioration, please be careful about use enough. We recommend use less than 30℃.

・ About the damage such as the losses of the data which occurred because of blackouts, we do not take responsibility.

・ The camera has aim to use by factories, commercial facilities and general households. Operating the camera close to a radio

and/or television may lead to interference, and then use the camera after change the installation position and / or wiring.

Notes on Use




|2/6|