Watec WAT-910HX Operation Manuals

Danger

Danger

Danger

Multi Function / Super High Sensitivi ty

WAT-910HX

Operation Manual

This Operation Manual covers safet y, camera functions, installation an d
the correct operating procedure for the WAT-910HX. First, we ask you
to read this Operation Manual thoroughly, then install and operate the
WAT-910HX as advised. In addition, for future referenc e, we also
advise safekeeping of this manual.

Please contact the distributor or dealer from which the WAT-910HX was
purchased, if you do not understand the installati on, operation or safety
instructions laid out in this manual. Not understanding the contents of
the Operation Manual sufficiently may c ause damage to the camera.

Guide to the Safety Symbols

The definitions of the symbols used i n this operation manual are:

When you do not adhere to or take notice of t he “Danger”
sign, it may lead to a serious accident such as death or
injury caused by fire or electri c shock.

When you do not adhere to or take notice of the “Warning”
sign, it may cause severe damage such as a physic al injury.

When you do not adhere to or take notice of the “Caution”
sign, it may incur injury and cause damage t o peripheral
objects in the immediate surroundings .

Cautions for Safety

The WAT-910HX is designed to be used safely; however, if not used
safely, it may lead to a physical accident caus ed by fire and electric
shock. Therefore, please keep and read t he “Cautions for safety” below
for protection against accidents.

• Do not disassemble and/or modify the WAT-910HX.

•

Do not operate the WAT-910HX with wet hands.

•

Use a stabilized power adaptor designed for DC+12V

±

10%, with a current capacity of more than 250m A for
the WAT-910HX.

The recommended voltage is DC+12V±10%

• Do not expose the WAT-910HX to wetness or high

moisture conditions.

The WAT-910HX is designed and approved for indoor use
only. The WAT-910HX is not water-resistant or waterpr oof.
If the location of the camera is outdoors or in an outdoor
like environment, we recommend that you use an outdoor
camera housing.

• Protect the WAT-910HX from condensation.

Keep the WAT-910HX dry at all times during storage and
operation.

• Should the camera not work properly, switch off the power

immediately. Then check the camera according to the
“Problems and Trouble shooting” section.

•

Avoid the striking of hard objects or dropping the
WAT-910HX.

The WAT-910HX uses high quality electrical parts and
precision components.

• Do not connect any power supply directly to the video

out terminal of the unit.

Do not connect the WAT-910HX with any monitor using a
video/power single transmiss ion terminal. The WAT­910HX is not designed for use with thi s type of
equipment. We also advise you to read the oper ation
manual of the monitor you plan to use bef ore any
connections are made.

• Do not install the WAT-910HX in a position subject to

direct sunlight.

Sunlight shinning directly onto t he WAT-910HX lens can
cause damage to the CCD.

• Select a stable place for installation of the WAT-910HX.

Use a support of durable strength around an i nstallation
position on a ceiling or wall when a cam era stand or tripod
is used.

• Do not move the WAT-910HX with the cables

connected.
Before moving the W AT-910HX, always remove the vide o
cable and power cable from the rear of the camera first.

• Avoid using th e WAT-910HX near any strong electro-

magnetic field.

After installing into main equipment, i f the WAT-910HX is
exposed to electromagnetic waves causing the monitored
image to become distorted, we recommend the c amera be
shielded by appropriate protect ive casing.

Problems and Trouble Shooting

If any of the following problems occur when using the WAT-9 10HX,

• An optimal picture cannot be obtained, after checking that all the

cables and connections are correct ly in place

• Smoke or any unusual odor emerges fr om the WAT-910HX

• An object becomes embedded or a quantit y of liquid seeps into the

camera housing

• More than the recommended voltage or/an d amperage has been

applied to the WAT-910HX by mi stake

• Anything unusual occurring to any equipm ent connected to the

WAT-910HX

Disconnect the camera immediately according t o the following
procedures:

①Switch off the main power supply to t he camera.

②Remove the power and video cables c onnected to the WAT-910HX.

③Contact the distributor or dealer fr om which the WAT-910HX was

purchased.

About EMC

The WAT-910HX is in conform ity with EMC test standards carried out
by authorized organizations i n Japan.

E I A FCC Part15 class B

CCIR EN61000-6-3/EN50130-4

※Please use

an auxiliary power supply (eg: UPS) to this camer a to comply

with EN50130-4 of EMC standards.

Do not modify the WAT-910HX. A modified camera may
not conform to EMC test standards.

Contents

Using the contents figures below, check to make sure al l parts are
present before use.

Lens Mount Cap WAT-910HX DC Plug Iris Connector

Description of Parts

①IMAGE SENSOR FRONT FACE

・

The light receiving face of the image sens or

(Dirt, water or oil deposits on the image sens or will cause an unclear
picture on the monitor. Attach the lens cap to pr otect the lens and the
CCD from contamination and damage.)

②LENS MOUNT

・

Mount for the lens (CS-mount)

③IRIS LEVEL VOLUME
・By controlling the volume, the ir is level of the DC iris lens can be

adjusted.

④FINE FOCUS ADJUSTMENT SCREWS

・

There are 3 hex. adjustment screws eac h placed at intervals of 120゜

for fine focusing of the lens.

⑤AUTO-IRIS SOCKET

・

This socket is for the video/DC auto-ir is lens cable connector.

(Video/DC: Auto selected by the camera)

⑥TRIPOD MOUNTING SCREW HOLES

・

Mounting holes for stands. The size of these t hreads are 1/4”, 20
threads, 4.5±0.2mm, which is the same as any standard camera
tripod (U1/4”).

⑦VIDEO OUT (BNC)

・

The terminal for composite video signal output

⑧OSD(On Screen Display) OPERATION DIAL

・

The jog-dial for setting the functions on the screen.

⑨I/O CONNECTOR

・

The control terminal for the Motion Detecti on.

⑩POWER IN

・

The terminal designed for connection wi th the DC-plug of the power
adaptor.

Power Supply

Use a stabilized power adaptor designed for DC+12V±10%, with a
current capacity of more than 250mA. Use the optional D C plug if the
shape or polarity of the DC plug of the power adaptor to be used is not
compatible with the camera (See the drawi ng on the right below).

The wiring of the connector must be e xact.
Be careful not to touch the other terminal while
wiring. Protect the wiring porti on by using insulation
tape after wiring. If the above care and attentio n is
not adhered to, damage to the WAT-910HX and
power adaptor may occur and may also c ause fire.

Auto-iris Lens

Before connecting the auto-ir is lens, please make sure that t he pin
configuration is correct by c onfirming with the following table. If the
configuration of your iris conne ctor is different from the followi ng, the
plug and pins will need to be rewired.

Pin No.

EIAJ Video

Auto-iris Lens

Arrangement

EIAJ DC

Auto-iris Lens

Arrangement

①

Power

Control －

②

Not used

Control ＋

③

Iris signals

Drive ＋

④

Common (GND)

Drive －

Set-up and Operation

1) Ensure that the power to the WAT-910HX and the peripheral
equipment is turned off before making any c onnections.

2) Remove the lens mount cap from the WAT-910HX and attach the
CS-mount lens. Use the optional C-mount adapt or (30CMA-R) when
a C-mount lens is used.

3) Connect the iris control cable to ⑤AUTO-I RIS SOCKET on the
WAT-910HX when an auto-iris lens is being used.

4) Connect ⑦VIDEO OUT on the WAT-910HX with the monitor, using
a coaxial cable with 75Ω impedance, such as an RG-59 or an
RG-6/U.
※Select a monitor with the same televis ion system as the WAT-

910HX EIA or CCIR. A monitor with more than 600TV lines is
recommended.

5) Insert the power plug of the power adaptor into ⑩POWER IN on the
back panel of the WAT-910HX. Confirm that the power adaptor is not
connected to the power supply before insertion of the power plug
into ⑩POWER IN.

6) Turn on the power to the WAT-910HX, monitor and all other allied
equipment. When a picture cannot be obtained on the monitor, or a
problem occurs, check and follow the procedure mentioned in the
【Problems and Trouble Shooting】section.

7) After following the procedure below and the picture i s still out of
focus, open the iris fully and loosen ④FINE FOCUSING
ADJUSTMENT SCREWS with the hex. wrench and mo ve the lens
forwards until a clear picture is obtai ned.

Manual Lens

Adjust the focus and iris to the best
position on the lens.

Video Auto-iris Lens Adjust the focus on the lens.

DC Auto-iris Lens

Adjust the iris level on the camera, then
adjust the focus on the lens. See below.

Iris Level Adjustment (for DC auto-iris lenses on ly)

Adjust ③IRIS LEVEL VOLUME placed on the side
of the unit until an acceptable light level is attained.
No change will occur if a video iris lens or manual
iris lens is fitted.

※ When an auto iris lens is used, set SHUTTER to 1/60 (1/50) , set

SENS UP to OFF and set AGC to OFF by ⑧OSD OPERATION
DIAL. Then adjust ③IRIS LEVEL VOLUME until an acceptable
light level is attained.

Warnin g

LEVEL

CLOSED

OPEN

DC+12V

COMMON(GND)

Cautio n

Warnin g

Cautio n

①

②

③

④

Warnin g

Cautio n

Hex. Wrench

Cable (300mm)

8) When detailed settings are required or an adequate image is not

obtained, set the functions on the screen by ⑧OSD OPERATION
DIAL.

9) When controlling the motion detection function, connect to ⑨I/O

CONNECTOR after wiring using the attached cable. See the pin
configuration as follows.

PIN No. Cable color Title Function

1

Brown MD_O Alarm out

2 Black GND Camera GND

3 - NC

■Alarm output terminal

When the motion detection function is used, the alarm output terminals
1 and 2 are hot during detection of movement in the monitored area.
If an LED is connected as shown in the diagram below, the alert turns
on the LED by voltage output of 3.3V at maximum current of 6mA.

Options

To purchase these options, please contact the distributor or dealer from
which you purchased the WAT -910HX.

Contact information

Contact information

Watec Co., Ltd.

Add.:I 254-2 Nihonkoku, Daihoji, Tsuruoka- Shi,

Yamagata-Ken, 997-0017 Japan
TEL: [phone] FAX: [phone]
E-mail: [e-mail]

URL: http://www.watec.co.jp

•

Design and specifications are subject to change without notice.

• Watec is not responsible for any inconvenience or the attendant damages

to the video and monitoring recording equipment caused by misuse, mis­operation or improper wiring of our equipment.

• If for any reason the WAT-910HX does not work properly, or if you have

any questions regarding installation or operation, please contact the
distributor or dealer from which it was purchased.

※Mimimum illumination specification applies to cameras with serial

numbers from W154BE01001/W154BC01001 and higher.

C-mount Adaptor (30CMA-R)

This lens mount adaptor is used
to convert a CS-mount to a C­mount.

Mini Stand (MS50)

A convenient stand for the
WAT-910HX. With this stand, the
camera can be adjusted to any
desired angle.

1542Z00-Y2000003