Watec WAT-902H2 ULTIMATE, WAT-902H3 ULTIMATE Operation Manuals

Hex. Wrench

Monochrome CCD Camera

WAT

WAT----902H

WATWAT
WAT

WAT----902H

WATWAT

902H

902H902H
902H

902H902H

2222

ULTIMATE

ULTIMATE

ULTIMATE ULTIMATE

3333

ULTIMATE

ULTIMATE

ULTIMATE ULTIMATE

Operation Manual

This Operation Manual covers safety, camera functions, installation and the
correct operating procedure for the WAT-902H
to read this Operation Manual thoroughly, then install and operate the
WAT-902H
advise safekeeping of this manual.

Please contact the distributor or dealer from which the WAT-902H
was purchased, if you do not understand the installation, operation or safety
instructions laid out in this manual. Not understanding the contents of the
Operation Manual sufficiently may cause damage to the camera.

2/3

ULTIMATE as advised. In addition, for future reference, we also

Guide to the Safety Symbols

The definitions of the symbols used in this operation manual are:

War ning

Cau tion

When you do not adhere to or take notice of the “Danger” sign, it

Dan ger

may lead to a serious accident such as death or injury caused by
fire or electric shock.

When you do not adhere to or take notice of the “Warning” sign, it
may cause severe damage such as a physical injury.

When you do not adhere to or take notice of the “Caution” sign, it
may incur injury and cause damage to peripheral objects in the
immediate surroundings.

Cautions for Safety

WAT-902H
safely, it may lead to a physical accident caused by fire and electric shock.
Therefore, please keep and read the “Cautions for Safety” below for protection
against accidents.

Dan ger

War ning

Cau tion

2/3

ULTIMATE is designed to be used safely; however, if not used

•

Do not disassemble and/or modify the WAT-902H
ULTIMATE.

•

Do not operate the WAT-902H

•

Use only the AD901-120/230 or equivalent power adaptor for
the WAT-902H

The recommended voltage is DC+12V±10%

•

Do not expose the WAT-902H
moisture conditions.

The WAT-902H
use only. The WAT-902H
resistant or waterproof. If the location of the camera is outdoors or
in an outdoor like environment, we recommend that you use an
outdoor camera housing.

•

Protect the WAT-902H

Keep the WAT-902H
and operation.

•

Should the camera not work properly, switch off the power
immediately. Then check the camera according to the “Problems
and Trouble Shooting” section.

•

Avoid the striking of hard objects or dropping the WAT­902H

2/3

The WAT-902H
and precision components.

•

Do not connect any power supply directly to the video out

terminal of the unit.

Do not connect the WAT-902H
using a video/power single transmission terminal. The WAT­902H

2/3

equipment. We also advise you to read the operation manual of
the monitor you plan to use before any connections are made.

•

Do not install the WAT-902H
subject to direct sunlight.

Sunlight shinning directly onto the WAT-902H
can cause damage to the CCD.

•

Select a stable place for installation of the WAT-902H
ULTIMATE.

Use a support of durable strength around an installation position
on a ceiling or wall when a camera stand or tripod is used.

•

Do not move the WAT-902H

connected.

Before moving the WAT-902H
video cable and power cable from the rear of the camera first.

2/3

ULTIMATE.

2/3

ULTIMATE is designed and approved for indoor

2/3

2/3

ULTIMATE.

2/3

ULTIMATE uses high quality electrical parts

ULTIMATE is not designed for use with this type of

2/3

ULTIMATE. First, we ask you

2/3

ULTIMATE

2/3

2/3

ULTIMATE with wet hands.

2/3

ULTIMATE to wetness or high

2/3

ULTIMATE is not water-

ULTIMATE from condensation.

ULTIMATE dry at all times during storage

2/3

ULTIMATE with any monitor

2/3

ULTIMATE in a position

2/3

2/3

ULTIMATE with the cables

2/3

ULTIMATE, always remove the

ULTIMATE lens

2/3

•

Avoid using the WAT-902H
electromagnetic field.

After installing into main equipment, if the WAT-902H
ULTIMATE is exposed to electromagnetic waves causing the
monitored image to become distorted, we recommend the camera
be shielded by appropriate protective casing.

2/3

ULTIMATE near any strong

Problems and Trouble Shooting

If any of the following problems occur when using the WAT-902H
ULTIMATE,

•

An optimal picture cannot be obtained, after checking that all the cables
and connections are correctly in place

•

Smoke or any unusual odor emerges from the WAT-902H

•

An object becomes embedded or a quantity of liquid seeps into the camera
housing

•

•

Disconnect the camera immediately according to the following
procedures:

①Switch off the main power supply to the camera.
②Remove the power and video cables connected to the WAT-902H

③Contact the distributor or dealer from which the WAT-902H

More than the recommended voltage or/and amperage has been applied
to the WAT-902H

Anything unusual occurring to any equipment connected to the WAT­902H

2/3

ULTIMATE.

purchased.

2/3

ULTIMATE.

ULTIMATE by mistake

2/3

ULTIMATE.

2/3

ULTIMATE was

About EMC

The WAT-902H
out by authorized organizations in Japan.

Dan ger

2/3

ULTIMATE is in conformity with EMC test standards carried

E I A /FCC Part15 class B

CCIR EN61000-6-3/EN50130-4

Do not modify the WAT-902H
may not conform to EMC test standards.

2/3

ULTIMATE. A modified camera

Contents

Using the contents figures below, check to make sure all parts are present before
use.

Lens Mount Cap WAT-902H

2/3

ULTIMATE

DC plug Iris connector

Description of Parts

③

④

①

②

⑧
⑨

⑤

⑪

⑫

⑩

①CCD FRONT FACE

・・・・The light receiving face of the CCD camera

(Dirt, water or oil deposits on the CCD will cause an unclear picture on the
monitor. Attach the lens cap to protect the lens and CCD from contamination
and damage.)

②LENS MOUNT

2/3

2/3

2/3

・・・・Mount for the lens (Thread type)
③IRIS LEVEL VOLUME
・By controlling the volume, the iris level of a DC iris lens can be adjusted.
④FOCUSING ADJUSTMENT SCREWS
・・・・There are 3 hex. adjustment screws each placed at intervals of 120゜for fine

focusing of the lens.

⑤AUTO-IRIS SOCKET
・・・・This socket is for a video or DC auto-iris lens cable connector.

(Video/DC: Auto selected by the camera)

⑥TRIPOD MOUNTING SCREW HOLES
・・・・Mounting holes for stands. The size of these threads are 1/4”, 20 threads, 4.5

±0.2mm, which is the same as any standard camera tripod (U1/4”).
⑦CAMERA BASE
・・・・The camera base has a thread for fixing to a standard tripod and four M3 size

holes for additional easy fixing.

⑧VIDEO OUT (BNC)
・・・・The terminal for composite video signal output
⑨GAMMA CORRECTION SWITCH
・・・・Three gamma values are selectable, 1.0, 0.45, 0.35.
⑩POWER IN
・・・・The terminal designed for the DC-plug of the power adaptor
⑪MGC VOLUME ADJUSTING
・The volume for setting manual gain control
⑫AGC/MGC SELECTION SWITCH
・Switch for setting AGC HI、LO or MGC
⑬BACK LIGHT
・・・・The switch for back light compensation
⑭ELECTRONIC SHUTTER ON/OFF SWITCH

・・・・The switch for the selecting electronic shutter mode
⑮AE MODE CONTROL
・・・・The switch for the shutter speed mode control according to the object being

monitored

Power Supply

If any other power adaptor besides the AD901-120/230 is used, please use a
stabilized power adaptor designed for DC+12V±10%, with a current capacity of
more than 250mA.
Use the optional DC plug if the shape or polarity of the DC plug of the power
adaptor to be used is not compatible with the camera (See the drawing on the
right below).

War ning

The wiring on the connector must be exact.
Be careful not to touch the other terminal while wiring.
Protect the wiring portion by using insulation tape after
wiring. If the above care and attention is not adhered to,
damage to the WAT-902H
adaptor may occur and may also cause fire.

Cau tion

2/3

ULTIMATE and power

DC+ 12V

COMMO N(GND )

Auto-iris Lens

Before connecting the auto-iris lens, please make sure that the pin configuration
is correct by confirming with the following table. If the configuration of your iris
connector is different from the following, the plug and pins will need to be
rewired.

⑥

⑦

⑬
⑭

⑮

④

③

There is a tripod mounting screw
hole as shown in the diagram on
the right .
In addition, there are 4 corners
holes M3 size and one φ5 for
stability.

②

Pin No.

①

①

②

③

④

EIAJ Video

Auto-iris Lens

Arrangement

Power

Not used

Iris signals

Common (GND)

EIAJ DC

Auto-iris Lens

Arrangement

Control －

Control ＋

Drive ＋

Drive －

Camera Base

Set-up and Operation

1) Ensure that the power to the WAT-902H
equipment is turned off before making any connections.

2) Remove the lens mount cap from the WAT-902H
CS-mount lens. Use the optional C-mount adaptor (30CMA-R) when a
C-mount lens is used.

3) Connect the iris control cable to ⑤AUTO-IRIS SOCKET on the WAT-902H
ULTIMATE when an auto-iris lens is being used.

4) Connect ⑧VIDEO OUT on the WAT-902H
using a coaxial cable with 75Ω impedance, such as an RG-58/U or an
RG-6/U. Select a monitor with the same television system as the

WAT-902H
is recommended.

5) Insert the power plug of the power adaptor into ⑩POWER IN on the back
panel of the WAT-902H
connected to the power supply before insertion of the power plug into ⑩
POWER IN.

6) Turn on the power to the WAT-902H

equipment. When a picture cannot be obtained on the monitor, or a problem
occurs, check and follow the procedure mentioned in the【Problems and
Trouble Shooting】section.

7) After following the procedure below and the picture is still out of focus, open

the iris fully and loosen ④FOCUSING ADJUSTMENT SCREWS with the hex.
wrench and move the lens forwards until a clear picture is obtained.

2/3

ULTIMATE: EIA or CCIR. A monitor with more than 600TV lines

2/3

ULTIMATE. Confirm that the power adaptor is not

Manual Lens

Video Auto-iris Lens Adjust the focus on the lens.

DC Auto-iris Lens

Adjust the focus and iris to the best position on
the lens.

Adjust the iris level on the camera, then adjust
the focus on the lens. See below.

Iris Level Adjustment (for DC auto-iris lenses only)

Adjust ③IRIS LEVEL VOLUME placed on the side
of the unit until an acceptable light level is attained.
No change will occur if a video iris lens or manual
iris lens is fitted.

8) Select any required gamma by the ⑨GAMMA CORRECTION SWITCH.

Mode Gamma Effect

OFF 1.0

LO 0.45

HI 0.35

※Select LO position for normal use. In a low light environment or dark

viewing, HI mode is recommended.

※The switch is set to LO(γ≒0.45) upon shipment.

9) Select any required gain control by the ⑫AGC/MGC SELECTION SWITCH.

Mode Range Effect

MGC 5 - 60dB

AGC HI 5 - 60dB

AGC LO 5 - 32dB

※The switch is set to LO(5-32dB) upon shipment.

10) Set the gain to any required environment by ⑪MGC VOLUME ADJUSTING.

Manually adjusted in a range between 5 to 60dB. In a low light environment,
when illumination of the object is important, increase the manual gain.
Lower the gain control for a clearer picture with less noise.

※The volume is set to L(Min.) upon shipment.

2/3

ULTIMATE and the peripheral

2/3

ULTIMATE and attach the

2/3

2/3

ULTIMATE with the monitor,

2/3

ULTIMATE, monitor and all other allied

CLOSE D

LEVE L

OPEN

Required for image processing such as data
storage for PCs and for FA.

Standard setting for using TVs and
Monitors. Natural images can be obtained
in dark areas.

Dark areas can be lightened and bright
areas can be reduced.

・In a low light environment, when

illumination of the object is important,
increase the manual gain. Lower the gain
control for a clearer picture with less
noise. (Factory automation or Image
processing)

・When minimum illumination is more

important than the S/N ratio
(Surveillance in a low light environment)

・When SN ratio is more important than

minimum illumination.

・When adequate lighting is present or a

stable lighting condition is available.

AC Adaptor (AD901

-

120/230)

for a constant

•

1340Z00

-

Y2000004

11) Select any required back light area by ⑬BACK LIGHT to one of its 4

Contact information

C-mount Adaptor (30CMA

-R)

Mini Stand (MS50)

positions.

1. Default

2. Center

3. Lower

4. Center + Lower

※The switches are set to OFF(Default) upon shipment.

12) Set the shutter mode by ⑭ELECTRONIC SHUTTER ON/OFF SWITCH
When shutter mode is OFF, fix the shutter speed to EIA1/60, CCIR1/50.
When shutter mode is ON, select the shutter speed mode by ⑮AE MODE
CONTROL.
※The switch is set to OFF upon shipment.

13) Select any required shutter speed by the ⑮AE MODE CONTROL to one of
its 10 positions.

No.

※An intense light may leave a trail on the screen longitude. This smearing is

a natural phenomenon and is not due to equipment failure or fault.

※The dial is set to 0(FL) upon shipment.

Mode

0 FL 1/100 1/120
1 ES 1/250
2 ES 1/500
3 ES 1/1000
4 ES 1/2000
5 ES 1/5000
6 ES 1/10000
7 ES 1/100000
8 EI: OFF 1/60-1/100000 1/50-1/100000
9 EI: FL 1/100-1/100000 1/120-1/100000

Area

Shutter Speeds (Sec.)

EIA CCIR

Switch

ON

1

ON

1

ON

1

ON

1

2

2

2

2

Options

To purchase these options, please contact the distributor or dealer from which
you purchased the WAT-902H

2/3

ULTIMATE.

The recommended AC adaptor for the
WAT-902H
and stable power supply.

2/3

ULTIMATE

This lens mount adaptor is used to
convert a CS-mount to a C­mount.

A convenient stand for the
WAT-902H
stand, the camera can be adjusted
to any desired angle.

2/3

ULTIMATE. With this

Specifications

WAT-902H2 ULTIMATE

Model

Pick-up Element 1/2 inch interline transfer CCD image sensor

Unit Cell Size

Minimum Illumination

Power Consumption

WAT-902H3 ULTIMATE

Model

Pick-up Element 1/3 inch interline transfer CCD image sensor

Unit Cell Size

Minimum Illumination

Power Consumption

WAT-902H2 ULTIMATE / WAT-902H3 ULTIMATE

Model

Number of

Total Pixels

Number of

Effective Pixels

Sync. System Internal

Scanning System 2:1 interlace

Video Output

Resolution (H) More than 570TVL (Center)

S/N

OFF 1/60 sec. 1/50 sec.

AE Mode

EI: OFF 1/60-1/100000 sec. 1/50-1/100000 sec.

EI: FL 1/100-1/100000 sec. 1/120-1/100000 sec.

AGC HI: 5-60dB / LO: 5-32dB

MGC 5-60dB

Gamma

Characteristics

Lens iris Video / DC (EIAJ arrangement, Auto-select)

Back Light

Compensation

Power Supply

Operating

Temperature

Operating Humidity Less than 95% RH

Storage Temperature

Storage Humidity Less than 95% RH

Lens Mount CS-mount (Back focus adjustable)

Size

Weight Approx. 98g

Design and specifications are subject to change without notice.

•

Watec is not responsible for any inconvenience or the attendant damages
to the video and monitoring recording equipment caused by misuse, mis­operation or improper wiring of our equipment.

•

If for any reason the WAT-902H
have any questions regarding installation or operation, please contact the
distributor or dealer from which it was purchased.

8.4μm(H)×9.8μm(V) 8.6μm(H)×8.3μm(V)

6.35μm(H)×7.4μm(V) 6.5μm(H)×6.25μm(V)

811(H)×508(V) 795(H)×596(V)

768(H)×494(V) 752(H)×582(V)

Composite video, 1.0 V(p-p) 75Ω (Unbalanced)

FL 1/100 sec. 1/120 sec.

ES

WAT-902H2 ULTIMATE

EIA CCIR

0.0001 lx. F1.4

1.32W (110mA)

WAT-902H3 ULTIMATE

EIA CCIR

0.0002 lx. F1.4

1.26W (105mA)

WAT-902H

EIA CCIR

More than 50dB (AGC=5dB, γ=1.0)

1/250, 1/500, 1/1000, 1/2000

1/5000, 1/10000, 1/100000 sec.

γ≒0.35(HI) / γ≒0.45(LO) / γ=1.0(OFF)

DC+12V±10%

-10 - +40℃ (Without condensation)

-30 - +70℃ (Without condensation)

36(W)×40(H)×63(L) (mm)

2/3

ULTIMATE does not work properly, or if you

2/3

ULTIMATE

ON / OFF

Watec Co., Ltd.

Watec Co., Ltd.

iAdd.: i254-2 Nihonkoku, Daihoji, Tsuruoka- Shi,

iYamagata-Ken, 997-0017 Japan

TEL: [phone] FAX: [phone]
Email: [e-mail]
URL: http://www.watec.net

Watec Co., Ltd.Watec Co., Ltd.