Watec WAT-902H2 SUPREME, WAT-902H3 SUPREME Operation Manual

Monochrome CCD Camera

Operation Manual

This Operation Manual covers safety, camera functions, installation and
the correct operating procedure for the WAT-902H
we ask you to read this Operation Manual thoroughly, then install and
operate the WAT-902H
reference, we also advise safekeeping of this manual.

2/3

SUPREME as advised. In addition, for future

Please co ntac t the distrib utor or de aler from which th e WAT­902H

2/3

SUPREME was purchased, if you do not understand the
installation, operation or safety instructions laid out in this manual. Not
understanding the contents of the Operation Manual sufficiently may
cause damage to the camera.

Guide to the Safety Symbols

The definitions of the symbols used in this operation manual are:

When you do not adhere to or take notice of the “Danger”

Dan ger

sign, it may lead to a serious accident such as death or
injury caused by fire or electric shock.

War ning

When you do not adhere to or take notice of the “Warning”
sign, it may cause severe damage such as a physical injury.

When you do not adhere to or take notice of the “Caution”

Cau tion

sign, it may incur injury and cause damage to peripheral
objects in the immediate surroundings.

Cautions for Safety

WAT-902H

2/3

SUPREME is designed to be used safely; however, if not
used safely, it may lead to a physical accident caused by fire and
electric shock. Therefore, please keep and read the “Cautions for
Safety” below for protection against accidents.

•

Dan ger

War ning

Cau tion

Do not disassemble and/or modify the WAT-902H
SUPREME.

•

Do not operate the WAT-902H

i

hands.

•

Use a stabilized power adaptor designed for DC+12V±±±±
10%, with a current capacity of more than 250mA for
the WAT-902H2/3 SUPREME.

The recommended voltage is DC+12V±10%

•

Do not expose the WAT-902H

or high moisture conditions.

The WAT-902H

2/3

SUPREME is designed and approved
for indoor use only. The WAT-902H
water-resistant or waterproof. If the location of the camera
is outdoors or in an outdoor like environment, we
recommend that you use an outdoor camera housing.

•

Protect the WAT-902H

2/3

SUPREME from

condensation.

Keep the WAT-902H
storage and operation.

•

Should the camera not work properly, switch off the power

2/3

SUPREME dry at all times during

immediately. Then check the camera according to the
“Problems and Trouble Shooting” section.

•

Avoid the striking of hard objects or dropping the WAT­902H

2/3

The WAT-902H

SUPREME.

2/3

SUPREME uses high quality electrical
parts and precision components.

2/3

SUPREME. First,

2/3

SUPREME with wet

2/3

SUPREME to wetness

2/3

SUPREME is not

2/3

•

iDo not connect any power supply directly to the video

out terminal of the unit.

Do not connect the WAT-902H

2/3

SUPREME with any
monitor using a video/power single transmission terminal.
The WAT-902H

2/3

SUPREME is not designed for use with
this type of equipment. We also advise you to read the
operation manual of the monitor you plan to use before any
connections are made.

•

Do not install the WAT-902H

2/3

SUPREME in a position

subject to direct sunlight.

Sunlight shinning directly onto the WAT-902H

S

UPREME lens can cause damage to the CCD.

•

Select a stable place for installation of the WAT­902H

2/3

SUPREME.

2/3

Use a support of durable strength around an installation
position on a ceiling or wall when a camera stand or tripod
is used.

•

Do not move the WAT-902H

2/3

SUPREME with the

cables connected.

Before moving the WAT-902H

2/3

SUPREME, always
remove the video cable and power cable from the rear of
the camera first.

•

Avoid using the WAT-902H

2/3

SUPREME near any

strong electromagnetic field.

After installing into main equipment, if the WAT-902H

2/3

SUPREME is exposed to electromagnetic waves causing
the monitored image to become distorted, we recommend
the camera be shielded by appropriate protective casing.

Problems and Trouble Shooting

If any of the following problems occur when using the WAT­902H

2/3

SUPREME,

•

An optimal picture cannot be obtained, after checking that all the
cables and connections are correctly in place

•

Smoke or any unusual odor emerges from the WAT-902H
SUPREME

•

An object becomes embedded or a quantity of liquid seeps into the
camera housing

•

More than the recommended voltage or/and amperage has been
applied to the WAT-902H

•

Anything unusual occurring to any equipment connected to the
WAT-902H

Disconnect the camera immediately according to the following procedures:

2/3

SUPREME.

2/3

SUPREME by mistake

2/3

①Switch off the main power supply to the camera.
②Remove the power and video cables connected to the WAT-902H

2/3

SUPREME.

③Contact the distributor or dealer from which the WAT-902H

2/3

SUPREME was purchased.

About EMC

The WAT-902H
carried out by authorized organizations in Japan.

2/3

SUPREME is in conformity with EMC test standards

E I A /FCC Part15 class B
CCIR EN61000-6-3/EN50130-4

Dan ger

Do not modify the WAT-902H
camera may not conform to EMC test standards.

2/3

SUPREME. A modified

Contents

Using the contents figures below, check to make sure all parts are
present before use.

Description of Parts

①CCD FRONT FACE

・The light receiving face of the CCD camera

(Dirt, water or oil deposits on the CCD will cause an unclear picture on
the monitor. Attach the lens cap to protect the lens and CCD from
contamination and damage.)

②LENS MOUNT
・Mount for the lens (Thread type)

③IRIS LEVEL VOLUME
・By controlling the volume, the iris level of a DC iris lens can be

adjusted.

④FOCUSING ADJUSTMENT SCREWS
・There are 3 hex. adjustment screws each placed at intervals of 120゜

for fine focusing of the lens.

⑤AUTO-IRIS SOCKET
・This socket is for a video or DC auto-iris lens cable connector.

(Video/DC: Auto selected by the camera)

⑥TRIPOD MOUNTING SCREW HOLES
・Mounting holes for stands. The size of these threads are 1/4”, 20

threads, 4.5±0.2mm, which is the same as any standard camera
tripod (U1/4”).

⑦AE MODE CONTROL

・

The switch for the shutter speed mode control according to the object
being monitored

⑧VIDEO OUT (BNC)
・The terminal for composite video signal output

⑨POWER IN
・The terminal designed for connection with the DC-plug of the power

adaptor

⑩AGC SELECTION SWITCH
・Switch for setting AGC HI or LO

Power Supply

Use a stabilized power adaptor designed for DC+12V±10%, with a
current capacity of more than 250mA.
Use the optional DC plug if the shape or polarity of the DC plug of the
power adaptor to be used is not compatible with the camera (See the
drawing on the right below).

War ning

Cau tion

The wiring on the connector must be exact.
Be careful not to touch the other terminal while

Hex. Wrench

wiring. Protect the wiring portion by using
insulation tape after wiring. If the above care and
attention is not adhered to, damage to the

Lens Mount Cap WAT-902H

2/3

SUPREME

DC plug Iris Connector

WAT-902H
occur and may also cause fire.

2/3

SUPREME and power adaptor may

DC+ 12V

COMMO N(GND )

Auto-iris Lens

Before connecting the auto-iris lens, please make sure that the pin
configuration is correct by confirming with the following table. If the
configuration of your iris connector is different from the following, the
plug and pins will need to be rewired.

Pin No.

④

③

②

①

②

①

③

④

EIAJ Video

Auto-iris Lens

Arrangement

Power

Not used

Iris signals

Common (GND)

Set-up and Operation

1) Ensure that the power to the WAT-902H

peripheral equipment is turned off before making any connections.

2) Remove the lens mount cap from the WAT-902H
attach the CS-mount lens. Use the optional C-mount adaptor
(30CMA-R) when a C-mount lens is used.

3) Connect the iris control cable to ⑤ AUTO-IRIS SOCKET on the
WAT-902H

2/3

SUPREME when an auto-iris lens is being used.

4) Connect ⑧VIDEO OUT on the WAT-902H
monitor, using a coaxial cable with 75Ω impedance, such as an
RG-58/U or an RG-6/U. Select a monitor with the same television

system as the WAT-902H
more than 600TV lines is recommended.

2/3

SUPREME: EIA or CCIR. A monitor with

5) Insert the power plug of the power adaptor into ⑨POWER IN on the
back panel of the WAT-902H

2/3

adaptor is not connected to the power supply before insertion of the
power plug into ⑨POWER IN.

6)

Turn on the power to the
other allied equipment. When a picture cannot be obtained on the
monitor, or a problem occurs, check and follow the procedure mentioned
in the【Problems and Trouble Shooting】section.

WAT-902H

7) After following the procedure below and the picture is still out of focus,
open the iris fully and loosen ④ FOCUSING ADJUSTMENT
SCREWS with the hex. wrench and move the lens forwards until a
clear picture is obtained.

Manual Lens

Adjust the focus and iris to the best
position on the lens.

Video Auto-iris Lens Adjust the focus on the lens.

Adjust the iris level on the camera, then

DC Auto-iris Lens

adjust the focus on the lens. See
below.

Iris Level Adjustment (for DC auto-iris lenses)

Adjust ③IRIS LEVEL VOLUME placed on the side
of the unit until an acceptable light level is attained.
No change will occur if a video iris lens or manual
iris lens is fitted.

8) Set the shutter mode by ⑦AE MODE CONTROL.

(Shutter mode is set to EI upon shipment.)

AE Mode

Automatically selects the shutter speed in the range

EI

between EIA: 1/60-1/100000 sec., CCIR: 1/50­1/100000 sec. according to the lighting condition.

Reduces the flickering phenomena occurring on the

FL

monitor screen caused by fluorescent or mercury
lamps.

OFF

Fixes the shutter speed to EIA: 1/60 sec., CCIR: 1/50
sec..

2/3

SUPREME and the

2/3

SUPREME. Confirm that the power

2/3

SUPREME

Effect

EIAJ DC

Auto-iris Lens

Arrangement

Control －

Control ＋

Drive ＋

Drive －

2/3

SUPREME and

SUPREME with the

, monitor and all

CLOSE D

LEVE L

OPEN

properly, or

9) Set the AGC mode by ⑩AGC SELECTION SWITCH.

Contact information

mount to

A convenient stand for the

(AGC mode is set to HI upon shipment.)

Mode

HI 5～50dB

LO

Range Effect

・When minimum illumination is more

important than the S/N ratio
(Surveillance in a low light
environment)

・When SN ratio is more important than

5～32dB

minimum illumination.

・When adequate lighting is present or

a stable lighting condition is
available.

Options

To purchase these options, please contact the distributor or dealer from
which you purchased the WAT-902H

2/3

SUPREME.

C-mount Adaptor (30CMA-R)

This lens mount adaptor is
used to convert a CS­a C-mount.

Mini Stand (MS50)

WAT-902H
this stand, the camera can be
adjusted to any desired angle.

2/3

SUPREME. With

Specifications

WAT-902H2 SUPREME

Model

Pick-up Element 1/2 inch interline transfer CCD image sensor

Unit Cell Size

Minimum Illumination

Power Consumption

WAT-902H3 SUPREME

Model

Pick-up Element 1/3 inch interline transfer CCD image sensor

Unit Cell Size

Minimum Illumination

Power Consumption

WAT-902H2 SUPREME / WAT-902H3 SUPREME

Model

Number of

Total Pixels

Number of

Effective Pixels

Sync. System Internal

Scanning System 2:1 interlace

Video Output

Resolution (H) More than 570TVL (Center)

S/N

AE

Mode

Characteristics

Back Light

Compensation

Power Supply

Operating

Temperature

Operating Humidity

Temperature

Storage Humidity Less than 95% RH

Lens Mount CS-mount

•

Design and specifications are subject to change without notice.

•

Watec is not responsible for any inconvenience or the attendant damages
to the video and monitoring recording equipment caused by misuse, mis­operation or improper wiring of our equipment.

•

If for any reason the WAT-902H
if you have any questions regarding installation or operation, please
contact the distributor or dealer from which it was purchased.

OFF 1/60 sec. 1/50 sec.

AGC HI: 5-50dB / LO: 5-32dB

Gamma

Lens iris Video / DC (EIAJ arrangement, Auto-select)

Storage

Size

Weight Approx. 90g

8.4μm(H)×9.8μm(V) 8.6μm(H)×8.3μm(V)

6.35μm(H)×7.4μm(V) 6.5μm(H)×6.25μm(V)

811(H)×508(V) 795(H)×596(V)

768(H)×494(V) 752(H)×582(V)

Composite video, 1.0 V(p-p) 75Ω (Unbalanced)

FL 1/100 sec. 1/120 sec.
EI 1/60-1/100000 sec. 1/50-1/100000 sec.

WAT-902H2 SUPREME

EIA CCIR

0.0003 lx. F1.4

1.98W (165mA)

WAT-902H3 SUPREME

EIA CCIR

0.0005 lx. F1.4

1.86W (155mA)

WAT-902H

EIA CCIR

More than 46dB (AGC=5dB, γ=1.0)

DC+12V±10%

-10 - +40℃ (Without condensation)

Less than 95% RH

-30 - +70℃ (Without condensation)

35.5(W)×36(H)×63(L) (mm)

2/3

SUPREME does not work

2/3

SUPREME

γ≒0.45

ON

Watec Co., Ltd.

Watec Co., Ltd.

Add.: 254-2 Nihonkoku, Daihoji, Tsuruoka- Shi,

TEL: [phone] FAX: [phone]
E-mail: [e-mail]

Yamagata-Ken, 997-0017 Japan

Watec Co., Ltd.Watec Co., Ltd.

1050Z00-Y2000008