Watec WAT-240E/FS Operation Manual

1/4” Miniature Color camera

WAT-240E/FS

Operation Manual

This operation manual covers safety, camera functions, installation and the
correct operating procedure for the WAT-240E/FS. First, we ask you to
read this operation manual thoroughly, then install and operate the
WAT-240E/FS as advised. In addition, for future reference, we also advise
safe keeping of this manual.

Please contact the distributor or dealer from which the WAT-240E/FS was
purchased, if you do not underst and the installation, operation or safety
instructions laid out in this manual. Not understanding the contents of the
operation manual sufficiently may cause damage to the camera.

Guide to the Safety Symbols

The definitions of the symbols used in this operation manual are:

“Danger”, may lead to a serious accident such as death or
injury caused by fire or electric shock.

“Warning”, may cause severe damage such as a physical
injury.

“Caution”, may incur injury and c ause damage to peripheral
objects in the immediate surroundings.

Cautions for Safety

WAT-240E/FS is designed to be used safely, however it may lead to a
physical accident caused by fire and electric shock if not used correctly.
Therefore, please keep and read the “Cautions for Safety” for protection
against accidents.



Do not disassemble and/or modify the WAT-240E/FS.



Do not operate the WAT-240E/FS with wet hands.



Use a stabilized power adaptor designed for DC+6V,
with a current capacity of more than 300mA for the
WAT-240E/FS
The recommended voltage is DC+4.6～6.6V.



Do not expose the WAT-240E/FS to wetness or high
moisture conditions.

The WAT-240E/FS is designed and approved for indoor use
only. The WAT-240E/FS is not water-resistant or waterproof.
If the location of the camera is outdoors or in an outdoor like
environment, we recommend that you use an outdoor
camera housing.



Protect the WAT-240E/FS from condensation.

Keep the WAT-240E/FS dry at all times during sto rage and
operation.



Should the camera not work properly, switch off the power
immediately. Then check the camera according to the
“Problems and Trouble Shooting” section.



Avoid the striking of hard objects or dropping the
WAT-240E/FS.

The WAT-240E/FS uses high quality electrical parts and
precision components.



Do not wire the WAT-240E/FS with any monitor using a
video/power single transmission terminal. The
WAT-240E/FS is not designed for use with this type of
equipment. We also advise you to read the operation
manual of the monitor you plan to use before any
connections are made.



Do not install the WAT-240E/FS in a position subject to
direct sunlight.

Sunlight shinning directly onto the WAT-240E/FS lens can
cause damage to the image sensor.



Select a stable place for installation of the
WAT-240E/FS.

Use a support of durable strength around an installation
position on a ceiling or wall when a camera stand or tripod
is used.



Do not move the WAT-240E/FS with the cables
connected.

Before moving the WAT-240E/FS, always remove the video
cable and power cable from the rear of the camera first.



Avoid using the WAT-240E/FS near any strong
electromagnetic field.

After installing into main equipment, if the WAT-240E/FS is
exposed to electromagnetic waves causing the monitored
image to become distorted, we recommend the camera be
shielded by appropriate protective casing.

Problems and Trouble Shooting

If any of the following problems occur when using the WAT-240E/FS,

 An optimal picture cannot be obtained, after checking that all the cables

and connections are correctly in place.

 Smoke or any unusual odor emerges from the WAT-240E/FS.
 An object becomes embedded or a quantity of liquid seeps into the

camera housing.

 More than the recommended voltage or/and amperage has been applied

to the WAT-240E/FS by mistake.

 Anything unusual occurring to any equipment connected to the

WAT-240E/FS.

Disconnect the camera immediately according to the following
procedures:

① Switch off the main power supply to the camera.
② Remove the power and video cables connected to the WAT-240E/FS.
③ Contact the distributor or dealer from which the WAT-240E/FS was

purchased.

Contents

Using the contents figures below, check to make sure all parts are present
before use.

① Lens (Upper: Type G3.8)
② WAT-240E/FS
③ Installation ring mount
④ Screw for ring mount (M2.6 x 8mm)
⑤ Nut for ring mount (M2.6)

Assembly and Setting Up

■When using the ring mount
【Setting of the ring mount】

Fix the mount by passing the ring over the lens of the camera, and then
attach the thread and nut.

※ Fix the ring on the housing with appropriate force and then check to

make sure the camera is fixed firmly and squarely. Improper setting
might cause damage to the camera cover.

Power Supply

Use a stabilized power adaptor designed for DC+6V, with a current
capacity of more than 300mA. Use the optional DC plug if the shape or
polarity of the DC plug of the power adaptor to be used is not compatible
with the camera.
The wiring on the connector must be exact.
Be careful not to touch the other terminals while wiring. Protect the wired
portion by using insulation tape after wiring. If the above care and attention
is not adhered to, damage to the WAT-240E/FS and power adaptor may
occur and may also cause fire.

【Diagram of output cable】

【Connection of output cables】

Set-up and Operation

① Refer to the【Connection of output cables】and the wiring must be exact.
② Join the video out cable with the video in cable of the monitor or

peripheral equipment.

③ Join the power supply using the correct procedure.
④ Make sure that a picture can be seen on the monitor
⑤ To focus, turn the lens clockwise or counterclockwise while observing

the picture on the monitor. Take care when focusing not to scratch or
damage the lens.

Options

Remote Controller (AVM-USB2)

AVM-USB2 is a compact controller with USB
connection for the WAT-240E/FS. Function
settings can be changed by the user according to
the environment from the PC.

For setting up and operation of the camera
remote control, please read and download the
"User Manual" from Watec website.

Holder (H002)

H002 is used for mounting the WAT-240E/FS with
ring mount. This holder has a U1/4”thread in the
center and a M2 thread in the four corners for
mounting on stands.

MS-50 (Mini Stand)

A convenient stand for the WAT-240E/FS. With
this stand, the camera can be adjusted to any
desired angle.

Contact information

 Design and specifications are subject to change without notice.

 Watec is not responsible for any inconvenience or the attendant

damages to the video and monitoring recording equipment caused by
misuse, mis-operation or improper wiring of our equipment.

 If for any reason the WAT-240E/FS does not work properly, or if you have

any questions regarding installation or operation, please contact the
distributor or dealer from which it was purchased.

Contact information

Watec Co., Ltd.

Add.:I 254-2 Nihonkoku, Daihoji, Tsuruoka- Shi,

Yamagata-Ken, 997-0017 Japan
TEL: [phone] FAX: [phone]
E-mail: [e-mail]
URL: http://www.watec.co.jp

1664Z00-Y2000A02